STM32F051K4T6 - 48MHz Cortex-M0 16KB Flash MCU | STMicroelectronics
부품 번호: STM32F051K4T6 ✓ 활성STM32F051K4T6 개요
A microcontroller is a semiconductor integrated circuit that integrates a processor core, memory, and peripherals into one device. The STM32F051K4T6 belongs to the STM32F0 family, where the STM32F0 series sits below higher-density STM32 families in processing capacity and I/O density. This device combines an ARM Cortex-M0 processor, Flash program memory, SRAM, general-purpose I/O, timers, serial interfaces, and analog conversion resources on a single integrated circuit.
The principal specifications include a 48 MHz maximum core frequency, 16 KB of Flash organized as 16K x 8 bits, and a 32-LQFP 7 x 7 mm package. The listed 2.0 V to 3.6 V operating range supports common 3.3 V embedded systems while allowing lower-voltage operation where component requirements permit. STMicroelectronics identifies the STM32F051xx family as incorporating a high-performance ARM Cortex-M0 32-bit RISC core and 11 timers, making the MCU appropriate for compact control systems requiring multiple timing and communication resources.
Technically, the STM32F051K4T6 is designed around a 32-bit RISC instruction set and a maximum clock rate of 48 MHz. Its peripheral mix supports embedded signal acquisition, motor-related control tasks, communications, and general digital control. Because the device is a low- and medium-density member of the STM32F0 platform, designers can use a common ecosystem of development tools while selecting a smaller package than larger STM32 devices. Exact RAM capacity, peripheral ratings, current consumption, and absolute maximum ratings must be confirmed in the manufacturer datasheet before a production design is released.
Typical uses include compact motor controllers, building and industrial sensor modules, appliance control boards, communication equipment, and low-cost consumer products. In these systems, the microcontroller can execute control logic, sample analog signals, operate timers, and manage serial data while requiring only a small PCB footprint. A 7 x 7 mm LQFP also remains visually inspectable after soldering and is easier to probe than the very small packages used in space-constrained wearable products.
Design decisions should focus on the complete electrical environment rather than the 48 MHz clock alone. Confirm the exact pin functions, decoupling requirements, exposed program and debug access, analog-reference connection, clock configuration, and unused-pin treatment in the manufacturer pinout and reference documentation. The LQFP footprint offers strong mechanical robustness, but every exposed signal still requires deliberate routing to preserve analog accuracy, timing margin, and reliable programming access.
This page combines the verified device identity, package information, operating range, engineering applications, drop-in alternatives, and design guidance in a format intended to accelerate component selection. It also highlights which detailed electrical and pin-level values require confirmation from the manufacturer datasheet, helping engineers move directly from source selection to a reviewable embedded design.
드롭인 대체품: STM32F051K4T6 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: STM32F051K4T6 (동일 폼 팩터 및 풋프린트) — 차이점: ADC, Flash Memory, Package.
STM32F050K4T6
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
STM32F051K8T6
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →STM32F050K8T6
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
STM32F051K4T6TR
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
STM32F051K4T6 최대 정격 & 전기적 특성
| Product Type | 32-bit ARM Cortex-M0 microcontroller |
| Manufacturer Part Number | STM32F051K4T6 |
| Base Part Number | STM32F051K4 |
| Processor Core | ARM Cortex-M0 32-bit RISC |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 16 KB (16K x 8 bits) |
| Operating Voltage Range | 2.0 V to 3.6 V |
| 패키지 | 32-pin LQFP, 7 x 7 mm |
| 실장 유형 | Surface mount |
| Timer Count | 11 timers |
| ADC | Present; resolution and channel count not stated |
| DAC | Present; resolution and channel count not stated |
| Program Memory | Flash |
| Product Series | STM32F0 |
| Core Architecture | ARM Cortex-M0 |
| 데이터 버스 폭 | 32 bits |
STM32F051K4T6 32-pin lqfp, 7 x 7 mm 핀 구성 가이드
STM32F051K4T6(32-pin lqfp, 7 x 7 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: STM32F051K4T6.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
STM32F051K4T6 적합 용도: 6 애플리케이션s: Compact Motor Control, Industrial Sensor Interface, Appliance Control Board, Communication Gateway Module, Low-Power Data Logger, Consumer Control Module.
Compact Motor Control
The STM32F051K4T6 is well suited to compact motor-control modules because its 48 MHz ARM Cortex-M0 core can execute control logic while the STM32F051 family provides 11 timers. Timer resources can support PWM generation, input capture, and timing functions needed by small BLDC, stepper, or actuator-control designs. The 32-LQFP 7 x 7 mm package preserves access to a relatively broad pin count compared with very small leadless packages. Before schematic release, verify the selected motor's required PWM channels, Hall or encoder inputs, ADC resolution, protection thresholds, and timing loops against the manufacturer pin and peripheral tables.
추천
Industrial Sensor Interface
The STM32F051K4T6 can act as the local controller for industrial sensor modules that require analog measurement, digital I/O, timers, and compact serial communication. Its 2.0 V to 3.6 V operating range fits 3.3 V sensor systems, while the 48 MHz core provides useful margin for sampling, filtering, calibration, and status reporting. The 7 x 7 mm LQFP is mechanically robust and easy to inspect during assembly. Designers should budget careful routing for analog inputs, follow the recommended decoupling arrangement, and confirm the ADC resolution, sampling time, input count, and serial-interface configuration in the manufacturer datasheet.
추천
Appliance Control Board
The STM32F051K4T6 fits appliance-control boards where a microcontroller must coordinate buttons, relays, indicators, sensors, and a small user interface. Its 48 MHz Cortex-M0 processing capability supports responsive state-machine control without requiring a high-power processor, and the 32-LQFP package offers a practical balance between pin access and board area. A robust design should include debouncing and protection for external switches, defined reset behavior, safe output states during firmware faults, and adequate supply decoupling. Verify the exact I/O voltage tolerances and maximum current ratings before connecting loads directly to GPIO pins.
추천
Communication Gateway Module
The STM32F051K4T6 can serve as the protocol-processing MCU in a small serial gateway that converts data between embedded interfaces or translates device commands. Its 48 MHz core is appropriate for lightweight framing, filtering, routing, and diagnostics, while 16 KB of Flash must be allocated carefully across boot code, protocol handlers, and update logic. The 32-LQFP package is suitable for compact modules that still require individually accessible leads. Designers should verify which UART, SPI, or I2C instances map to usable pins, and should validate boot and recovery behavior if the module is intended for remote deployment.
추천
Low-Power Data Logger
The STM32F051K4T6 is applicable to compact data-logging modules that periodically sample sensors, store locally, and transmit results through a serial interface. Its 48 MHz Cortex-M0 core provides ample execution speed for short acquisition and formatting tasks, while the 2.0 V to 3.6 V range supports low-voltage designs. The limited 16 KB Flash makes efficient code and data management important, so engineers should separate firmware from nonvolatile data storage and avoid placing large logs in MCU Flash. Exact SRAM, low-power modes, wake-up sources, and peripheral clock requirements must be confirmed in the manufacturer datasheet.
추천
Consumer Control Module
The STM32F051K4T6 supports compact consumer modules that coordinate buttons, displays indicators, manage simple actuators, or implement a product-specific control sequence. Its ARM Cortex-M0 architecture provides a common embedded development ecosystem, and the 32-LQFP package is easier to assemble and inspect than a leadless package with the same functional density. A successful design still requires careful attention to power sequencing, brownout behavior, exposed debug access, firmware recovery, and GPIO overvoltage protection. The 16 KB Flash capacity should be checked against the final application image and any planned update mechanism.
추천
추천 제품 요약
엔지니어링 참조 데이터: STM32F051K4T6 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | STM32F050K4T6 | STM32F051K8T6 | STM32F050K8T6 | STM32F051K4T6TR |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 32-LQFP (7 x 7 mm) | 32-LQFP (7 x 7 mm) | 32-LQFP (7 x 7 mm) | 32-LQFP (7 x 7 mm) | 32-LQFP (7 x 7 mm) |
| Processor Core | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 |
| Maximum CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 16 KB | 16 KB | 64 KB | 64 KB | 16 KB |
| Product Series | STM32F051 | STM32F050 | STM32F051 | STM32F050 | STM32F051 |
| Ordering Configuration | T6 standard LQFP order code | T6 LQFP order code | T6 LQFP order code | T6 LQFP order code | TR tape-and-reel order code |
주요 차별점
- Uses 16 KB of Flash in a compact 32-LQFP package (vs STM32F051K8T6)
- Retains the full STM32F051 family feature set at 48 MHz (vs STM32F050K4T6)
- Matches the exact verified electrical identity of the T6 device (vs STM32F051K4T6TR)
- Provides a compact 7 x 7 mm surface-mount footprint (vs STM32F051C4T6)
설계 노트
Use the manufacturer LQFP-32 land pattern and pin-1 orientation without moving the footprint to accommodate a different package option. Keep the exposed programming and debug signals accessible, provide a stable ground reference, and route sensitive analog inputs away from fast digital clocks. Before fabrication, compare the board's pin assignments with the manufacturer pin-description table for every power, ground, reset, clock, and peripheral connection.
Design the supply around the verified 2.0 V to 3.6 V device range while ensuring every external component and signal remains within its own limits. Place the recommended local bypass capacitors at the device supply pins with short ground returns, and account for startup current when sizing the regulator. If the MCU is powered during a brownout or reset, use external supervision or reset control when system state must remain deterministic.
Do not assume that two STM32F0-family devices with similar speed and package are firmware-identical. The STM32F050 alternatives may differ in peripheral behavior, while STM32F051K8T6 and STM32F050K8T6 provide 64 KB of Flash rather than 16 KB. Before substituting a part, compare clock tree configuration, interrupt vectors, timer channels, pin alternate functions, bootloader behavior, flash programming, and maximum operating conditions.
Route clock, debug, and communication signals with return paths that do not cross high-current or switching nodes. Keep analog grounds and references quiet, use a continuous ground reference, and place input protection close to the connector. If an external crystal, fast SPI interface, or Ethernet PHY is added, calculate worst-case rise and fall times and review the external component recommendations in the manufacturer hardware guidance.
규정 준수 정보
The manufacturer product listing does not expose explicit compliance declarations in the available material. Verify RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status for the exact order code using current STMicroelectronics documentation.