STM8L101G2U6 - 16MHz 8-Bit Ultra-Low-Power MCU | STMicroelectronics
부품 번호: STM8L101G2U6 ✓ 활성STM8L101G2U6 개요
An ultra-low-power microcontroller is a microcontroller optimized to minimize energy use during active processing, idle periods, and low-power operating states. The STM8L101 family belongs to the STM8L EnergyLite line and combines an 8-bit CPU, direct-memory-access peripherals, low-power modes, and communication interfaces in a single device. This hierarchy places it within the broader category of embedded processors and system-on-chip devices used for sensing, monitoring, control, and compact communications.
The STM8L101G2U6 provides 4 KB of Flash organized as 4K x 8, with the STM8L101x2 device family supporting up to 8 Kbytes of Flash according to the manufacturer family description. Its communication resources include USART, SPI, and I2C, while multifunction timers and comparators support motor, control, sensing, and threshold-detection applications. The 16 MHz maximum clock frequency provides up to 16 MIPS of processing performance according to the STM8L101 family information.
The 28-pin package exposes 18 general-purpose I/O ports according to the available component specifications, allowing connections to sensors, displays, actuators, communications transceivers, and human-interface controls. The 4 x 4 mm UFQFPN construction supports dense layouts but requires careful PCB planning because exposed-pad and fine-pitch soldering techniques are commonly needed for reliable assembly and thermal performance.
Typical uses include low-voltage sensor nodes, compact motor controllers, battery-operated instruments, industrial monitoring modules, LED lighting controllers, and connected IoT edge devices. In each case, the STM8L101G2U6 acts as the central controller by executing application firmware, sampling analog or digital inputs, coordinating timers, and exchanging data through its serial interfaces.
Designers should verify the exact pin assignments, alternate-function limitations, decoupling requirements, and exposed-pad connection using the manufacturer pinout and reference-design guidance. Low-power operation also depends on firmware: unused peripherals should be disabled, GPIO pins should be placed in suitable states, and wake-up behavior should be tested under the intended clock and load conditions.
This product page consolidates the core STM8L101G2U6 specifications, interface capabilities, package considerations, application guidance, and same-family replacement information into an engineering-focused reference for compact low-voltage embedded designs.
드롭인 대체품: STM8L101G2U6 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: STM8L101G2U6 (동일 폼 팩터 및 풋프린트) — 차이점: Flash Memory, Package, Package Dimensions, Product Type, Supply Voltage Range.
STM8L101G3U6A
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
STM8L151G2U6
✅ 드롭인가격 문의
데이터시트 보기 →STM8L101G1U6
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
STM8L101G4U6
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
STM8L101G3U6
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →STM8L101G2U6 최대 정격 & 전기적 특성
| Product Type | 8-bit ultra-low-power microcontroller |
| Manufacturer | STMicroelectronics |
| 최대 클록 주파수 | 16 MHz |
| Maximum Processing Performance | 16 MIPS at 16 MHz |
| Flash Memory | 4 KB (4K x 8) |
| Supply Voltage Range | 1.65 V to 3.6 V |
| General-Purpose I/O Ports | 18 ports |
| 패키지 | 28-pin UFQFPN |
| Package Dimensions | 4 x 4 mm |
| Package Height | 0.60 mm |
| CPU Core | Enhanced STM8 8-bit core |
| Serial Interfaces | USART, SPI, and I2C |
| Analog and Timing Resources | Comparators and multifunction timers |
| Lifecycle Stage | Active |
| RoHS 상태 | RoHS compliant |
| 실장 유형 | Surface mount |
STM8L101G2U6 0.60 mm 핀 구성 가이드
STM8L101G2U6(0.60 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: STM8L101G2U6.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
STM8L101G2U6 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Node, Compact Motor Controller, Industrial Monitoring Terminal, Smart Lighting Controller, IoT Edge and Wireless Gateway, Portable Measurement Instrument.
Battery-Powered Sensor Node
The STM8L101G2U6 fits compact sensor nodes because its 1.65 V to 3.6 V supply range supports low-voltage energy budgets and its ultra-low-power architecture reduces the burden on primary batteries. The 4 KB of Flash can hold a focused acquisition and reporting application, while 18 I/O ports connect switches, analog sensors, status indicators, and an external radio. USART or I2C can carry sensor data to a communications module, and SPI can support higher-throughput peripherals. Firmware should disable unused blocks, configure unused GPIOs for minimal leakage, and use the manufacturer’s low-power modes to establish a realistic duty cycle. Validate battery life with the complete sensor and radio load rather than the microcontroller alone.
추천
Compact Motor Controller
The STM8L101G2U6 can serve as the command center for a small stepper, fan, pump, or actuator controller where its multifunction timers and 18 I/O ports are valuable. The 16 MHz CPU provides enough execution speed for sequencing, position counting, fault monitoring, and communication housekeeping, while the low 1.65 V minimum supply supports low-voltage motor systems. Drive transistors should handle the motor current, while comparators and timer inputs can supervise position or fault signals. The principal design constraint is power dissipation in the external driver stage: the MCU itself should not directly carry motor current. Confirm timer pin mapping, electrical limits, stall conditions, thermal rise, and emergency shutdown behavior before production release.
추천
Industrial Monitoring Terminal
The STM8L101G2U6 is appropriate for compact industrial monitoring equipment that gathers switch, sensor, or alarm information and forwards it over a serial network. Its 18 I/O ports reduce the need for external I/O expanders, while USART, SPI, and I2C cover common sensor, display, and transceiver connections. Operating from 1.65 V to 3.6 V allows integration with low-voltage industrial rails, although the exact temperature rating must be confirmed for the deployed environment. Use the comparators for local threshold detection, timers for periodic sampling, and the serial interface for supervisory communication. Production designs should include transient protection, ground-quality planning, watchdog behavior, and safe recovery after communication loss or power restoration.
추천
Smart Lighting Controller
The STM8L101G2U6 can control compact LED lighting modules because its timers support periodic dimming and timing functions, its comparators can detect thresholds, and 18 I/O ports leave room for button inputs, status feedback, and driver-control signals. The 4 KB Flash footprint is adequate for focused lighting logic, including schedules, fade sequences, and communication handling, provided the firmware remains within the memory limit. A low-voltage LED architecture aligns with the MCU’s 1.65 V to 3.6 V operating range, but the LED driver and MOSFET stage determine current capability and switching losses. Validate flicker, dimming resolution, startup current, thermal behavior, and fail-safe illumination when the controller loses power or communication.
추천
IoT Edge and Wireless Gateway
The STM8L101G2U6 works well as a low-power edge controller for a compact wireless sensor endpoint because its serial interfaces can connect to a radio module while the CPU handles local configuration, data filtering, and simple protocol conversion. The 16 MHz enhanced STM8 core supports up to 16 MIPS, providing useful headroom for protocol maintenance without moving to a larger MCU. Its 4 KB Flash is suitable only for focused gateway logic, so buffering and complex protocol stacks may require external memory or a different controller. Low-power behavior depends on coordinating radio sleep intervals with MCU wake-up timing and configuring unused pins correctly. Validate data latency, standby current, recovery behavior, and the operating-temperature range on the finished assembly.
추천
Portable Measurement Instrument
The STM8L101G2U6 can support portable measurement instruments where a low-power 8-bit MCU must coordinate a sensor, display, controls, and data transfer. Its comparators support threshold decisions, timers support periodic measurements, and USART, SPI, or I2C can connect to converters, memory, and displays. The 1.65 V to 3.6 V operating range enables operation from low-voltage cells or regulated sources, but battery regulators and analog front ends remain essential for precision measurement. Firmware should average or filter readings, monitor battery state, and provide predictable shutdown behavior. Validate analog noise, display refresh energy, sensor warm-up time, calibration retention, and accuracy across the full temperature range before defining the instrument specification.
추천
추천 제품 요약
엔지니어링 참조 데이터: STM8L101G2U6 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | STM8L101G3U6A | STM8L151G2U6 | STM8L101G1U6 | STM8L101G4U6 | STM8L101G3U6 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 28-pin UFQFPN, 4 x 4 mm | 28-pin UFQFPN, 4 x 4 mm | 28-pin UFQFPN, 4 x 4 mm | 28-pin UFQFPN, 4 x 4 mm | 28-pin UFQFPN, 4 x 4 mm | 28-pin UFQFPN, 4 x 4 mm |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Supply Voltage Range | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V |
| CPU Architecture | 8-bit enhanced STM8 core | 8-bit enhanced STM8 core | 8-bit enhanced STM8 core | 8-bit enhanced STM8 core | 8-bit enhanced STM8 core | 8-bit enhanced STM8 core |
| Serial Interfaces | USART, SPI, I2C | USART, SPI, I2C | USART, SPI, I2C | USART, SPI, I2C | USART, SPI, I2C | USART, SPI, I2C |
| General-Purpose I/O | 18 ports | 18 ports | 18 ports | 18 ports | 18 ports | 18 ports |
| Special Resources | Multifunction timers and comparators | Multifunction timers and comparators | Multifunction timers and comparators | Multifunction timers and comparators | Multifunction timers and comparators | Multifunction timers and comparators |
| Processing Performance | Up to 16 MIPS at 16 MHz | Up to 16 MIPS at 16 MHz | Up to 16 MIPS at 16 MHz | Up to 16 MIPS at 16 MHz | Up to 16 MIPS at 16 MHz | Up to 16 MIPS at 16 MHz |
주요 차별점
- Compact 4 x 4 mm implementation with 18 I/O ports (vs STM8L151G2U6)
- Lower flash requirement reduces firmware and memory pressure for focused applications (vs STM8L101G4U6)
- 16 MHz processing with USART, SPI, and I2C in a 28-pin package (vs STM8L101G1U6)
설계 노트
The STM8L101G2U6 operates from 1.65 V to 3.6 V, so power-supply design must remain valid across both startup and active-current conditions. Place the manufacturer-required decoupling capacitors close to the supply and ground pins, and use a regulator with adequate transient response for radio or sensor load changes. Treat GPIO leakage, pull networks, LED indicators, and external transceivers as part of the standby-current budget because the MCU may be idle while the rest of the node remains active.
Use the exact 28-pin UFQFPN land pattern and assembly process recommended for this ordering code. Route each power and ground connection carefully, keep the exposed-pad treatment consistent with the manufacturer guidance, and avoid long return paths beneath switching or high-current traces. Confirm which pins provide power, ground, reset, debug, and peripheral functions in the manufacturer pin table before routing. A generic 20-pin QFN footprint must not be substituted because its lead count and pin assignments differ.
The 4 KB Flash limit can be reached quickly when application code, bootloader functions, and data constants share the device. Check the final map file, reserve space for a planned firmware revision, and avoid designs that assume the broader family’s up-to-8-Kbyte capacity applies to every member. Also validate alternate-function conflicts among USART, SPI, I2C, timers, comparators, and debug pins. The 18 available I/O ports do not imply that every peripheral function can be used simultaneously on those pins.
The STM8L101G2U6 is a low-power controller, but overall junction temperature still depends on ambient conditions, switching losses in connected drivers, copper area, and the package thermal path. Keep high-current LED or motor drive stages physically separated from the MCU area, provide adequate ground and copper around the package, and measure temperature under worst-case operating conditions. Do not infer thermal performance from the low operating voltage alone; validate the complete assembly during maximum processing, communication, and external load activity.
규정 준수 정보
The component listing identifies the STM8L101G2U6 as RoHS compliant. No specific REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is identified for this ordering code.
