SY89464UMG - 2:10 2 GHz LVPECL Clock Multiplexer | Microchip
부품 번호: SY89464UMG ✓ 활성SY89464UMG 개요
A clock multiplexer is a timing-device category used to route one of multiple clock signals onto a downstream circuit while preserving differential signal integrity. Clock buffers extend a source across multiple loads, while a multiplexer adds source selection for redundant systems. The SY89464UMG therefore combines clock distribution and source switching in one timing IC, placing it within the hierarchy of clock multiplexer, clock buffer, clock and timing IC, and semiconductor.
Key features include a 2:10 multiplexer configuration, operation to 2 GHz, differential input support, differential LVPECL outputs, low-jitter operation, internal termination, and a runt-pulse eliminator. The 2:1 input stage is optimized for redundant-source switchover, where a system may switch between primary and backup clocks. Its ten outputs support fanout to multiple destination circuits while retaining a common differential LVPECL interface.
The SY89464U combines source selection with a 1:10 fanout stage rather than functioning as a simple single-input distributor. The manufacturer describes the product as a low-jitter 1:10 LVPECL fanout buffer with a 2:1 differential input multiplexer. Differential signal handling is particularly useful when the clock path must remain resistant to common-mode noise. The internal termination and runt-pulse elimination features help control reflection and unwanted narrow pulses in demanding backplane, telecommunications, and data-center clocking systems.
Typical uses include redundant clock distribution in telecommunications equipment, server backplanes, network switches, test and measurement systems, and high-speed digital subsystems. A 2 GHz operating limit supports high-speed reference or forwarded clocks, while the ten LVPECL outputs can feed several endpoints from one selected source. The 44-VFQFN exposed-pad package provides the thermal-contact geometry needed for a multi-output high-speed device, although system-level thermal performance still depends on the PCB pad and copper design.
PCB implementation should preserve differential impedance and minimize mismatch between the complementary clock traces. Place input and output decoupling near the corresponding device pins, provide a continuous ground reference, and connect the exposed pad to a properly designed ground plane using the manufacturer’s recommended land pattern. Differential input and output traces should have equal length and geometry, with return-path discontinuities minimized. Validate source-switchover timing, output jitter, and runt-pulse behavior at the intended clock frequency in the final system.
This page consolidates the functional description, package information, sourcing guidance, verified drop-in relationship, and practical implementation considerations for the SY89464UMG. It is intended to help engineers identify whether the part fits a redundant differential-clock architecture before consulting the manufacturer datasheet and pin-description table for final PCB implementation.
드롭인 대체품: SY89464UMG — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: SY89464UMG (동일 폼 팩터 및 풋프린트) — 차이점: Output Configuration, Package.
SY89464UMY
✅ 드롭인가격 문의
데이터시트 보기 →SY89464UMG 사양
| Product Type | 2:10 differential clock multiplexer and 1:10 LVPECL fanout buffer |
| Multiplexer Configuration | 2:1 differential input multiplexer |
| 출력 구성 | 1:10 fanout |
| Maximum Operating Frequency | 2 GHz |
| Input Signal Types | CML, LVDS, and PECL differential inputs |
| Output Signal Type | Differential LVPECL |
| Jitter Performance | Low-jitter operation |
| Input Termination | Internal termination |
| Pulse Control | Runt-pulse eliminator |
| Primary Application | Redundant source switchover |
| 패키지 | 44-VFQFN exposed pad, 44-MLF |
| 핀 수 | 44 pins |
| 실장 유형 | Surface mount |
SY89464UMG 44-vfqfn exposed pad, 44-mlf 핀 구성 가이드
SY89464UMG(44-vfqfn exposed pad, 44-mlf 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: SY89464UMG.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
SY89464UMG 적합 용도: 6 애플리케이션s: Redundant Server Clock Distribution, Telecommunications Backplane Clocking, Network Switch Reference Distribution, High-Speed Test and Measurement Equipment, Data Center Fabric Clocking, Industrial High-Speed Control Systems.
Redundant Server Clock Distribution
The SY89464UMG fits redundant server clocking because its 2:1 differential input multiplexer can select between two clock sources and feed ten differential LVPECL outputs. The device operates up to 2 GHz, allowing one selected reference to reach multiple server, fabric, or interface clock domains. Low-jitter operation, internal termination, and runt-pulse elimination help preserve timing quality during source selection. The 44-VFQFN exposed pad also provides a practical thermal path when several high-speed outputs operate continuously.
Telecommunications Backplane Clocking
In telecommunications backplanes, the SY89464UMG can select a primary or backup differential clock and distribute it to ten downstream LVPECL destinations. Its support for CML, LVDS, and PECL inputs allows different clock sources to interface with the same multiplexing stage, while differential outputs reduce sensitivity to common-mode noise on long interconnects. Operation to 2 GHz and the low-jitter 1:10 fanout architecture suit high-speed line cards, switching fabrics, and timing-distribution systems requiring deterministic source redundancy.
Network Switch Reference Distribution
The SY89464UMG is suitable for distributing a selected reference clock across a network-switch line card. Its two differential inputs support failover between clock sources, and its ten LVPECL outputs provide one-to-ten fanout without requiring ten separate buffer packages. The 2 GHz maximum operating frequency covers demanding SerDes and fabric reference-clock environments. Internal termination and the runt-pulse eliminator improve signal control, although the board must maintain continuous return paths and matched differential geometry.
High-Speed Test and Measurement Equipment
The SY89464UMG can serve as a redundant reference and fanout element in high-speed test and measurement systems. Two selectable differential inputs allow the instrument to switch between an internal reference and an external clock, while ten LVPECL outputs can feed trigger, acquisition, or calibration circuits. Its low-jitter operation and 2 GHz capability suit high-speed timing systems. The exposed-pad package should be paired with a thermal-aware via array and sufficient copper to dissipate heat from sustained multi-output operation.
Data Center Fabric Clocking
The SY89464UMG fits data-center fabric clocking where multiple endpoints require a common, selectable differential clock. The 2:1 multiplexer provides a transition path between redundant sources, and the 1:10 fanout reduces the number of separate distribution buffers required around the fabric interface. Differential LVPECL outputs maintain a consistent interface across up to ten loads at frequencies as high as 2 GHz. Designers should still verify per-output loading, channel skew, jitter contribution, and power distribution for each particular system architecture.
Industrial High-Speed Control Systems
The SY89464UMG can support source redundancy in industrial systems that distribute a high-speed clock to multiple controllers, converters, or communication blocks. CML, LVDS, and PECL differential input options make it practical to combine clock sources from different interface sections, and ten LVPECL outputs provide centralized fanout. The low-jitter architecture and 2 GHz limit are valuable when timing margins are tight. Its exposed-pad package requires careful PCB thermal design because sustained fanout operation can raise junction temperature in compact industrial enclosures.
엔지니어링 참조 데이터: SY89464UMG — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | SY89464UMY |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 44-VFQFN exposed pad, 44-MLF | 44-VFQFN exposed pad, 44-MLF |
| Product Function | 2:10 clock multiplexer with 1:10 LVPECL fanout | 2:10 clock multiplexer with 1:10 LVPECL fanout |
| Application Focus | Redundant source switchover | Redundant source switchover |
주요 차별점
- Combines redundant-source selection with ten-output distribution (vs SY89464UMY)
- Supports several differential source formats (vs SY89464UMY)
- Includes signal-control features for redundant clocking (vs SY89464UMY)
설계 노트
Route the differential clock inputs and outputs as matched pairs over a continuous ground reference. Maintain equal geometry and controlled impedance for each P and N conductor, avoid stubs, and minimize layer changes because discontinuities can create reflections that increase jitter or trigger the runt-pulse eliminator unexpectedly. Confirm the final stack-up and trace dimensions against the manufacturer’s interface and layout guidance.
The 44-VFQFN exposed pad must be connected to a carefully designed thermal via array and ground copper to remove heat from the die. Keep nearby copper from encroaching on other sensitive routing unless the manufacturer land pattern explicitly permits it. Validate junction temperature under worst-case ambient conditions, full output loading, and sustained 2 GHz operation rather than relying only on a short bench test.
Check each clock source for valid differential amplitude, common-mode range, duty-cycle distortion, and edge-rate behavior before enabling the selected input. Because the device performs both source selection and 1:10 fanout, input return loss and output loading can influence edge quality. Use the manufacturer’s termination and output-loading requirements, and verify source-switchover behavior with the actual clock generators and final board parasitics.
규정 준수 정보
Compliance declarations for RoHS, REACH, AEC-Q100, lead-free status, halogen-free status, and conflict minerals were not identified in the product information. Check the current manufacturer product page or material declaration before procurement.