TDA8763M/4/C4 - 10-bit 40MSPS Sigma-Delta ADC | NXP
부품 번호: TDA8763M/4/C4 ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $12.5 | $12.50 |
| 10 | $11.2 | $112.00 |
| 100 | $9.85 | $985.00 |
| 500 | $8.4 | $4,200.00 |
| 1,000 | $7.1 | $7,100.00 |
TDA8763M/4/C4 개요
What is a sigma-delta ADC? A sigma-delta (ΣΔ) ADC is a type of analog-to-digital converter that uses oversampling and noise shaping to achieve high resolution from a relatively coarse quantizer. Unlike successive-approximation (SAR) or flash ADCs that resolve a sample in one conversion step, the sigma-delta ADC trades speed for resolution, averaging many low-bit samples to produce a high-accuracy output. Within the broader converter hierarchy, it sits as a sub-type of Nyquist-rate ADCs, while it excels in applications where bandwidth is moderate and signal-to-noise ratio (SNR) must be high.
Key features of the TDA8763M/4/C4 include a 10-bit resolution, 40 MSPS sampling rate, single analog input channel, internal reference regulator that eliminates an external reference IC, and low-power operation suitable for portable instrumentation. The integrated regulator stabilizes the internal reference voltage against supply variations, improving DC accuracy across temperature. The parallel output bus simplifies digital interface design by removing the need for serialization or external clock-data recovery.
Architecturally, the device combines a sigma-delta modulator with a decimating digital filter and a parallel output register. The internal reference regulator provides a low-drift, low-noise reference voltage, while the input stage accepts single-ended or differential analog signals. The 28-pin SSOP package offers a compact footprint suitable for space-constrained applications.
Typical applications include industrial process control, medical instrumentation, CCD imaging digitizers, video signal processing, and portable test equipment. The combination of 10-bit resolution and 40 MSPS sampling makes the device well-suited to digitizing IF-stage signals, ultrasound return paths, and intermediate-frequency communication channels.
When designing with this device, ensure adequate decoupling on both AVDD and DVDD rails, follow the recommended input common-mode voltage range, and observe the timing requirements on the parallel output bus. The internal reference regulator eliminates the need for an external reference but still requires proper bypass capacitance near the REF pin.
This page synthesizes distributor pricing, drop-in alternatives, application guidance, and design notes not consolidated in the manufacturer datasheet, enabling faster part selection for engineers.
드롭인 대체품: TDA8763M/4/C4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: TDA8763M/4/C4 (동일 폼 팩터 및 풋프린트) — 차이점: Architecture, Input Type, Number of Channels, Package, Sampling Rate.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
TDA8763M/4/C4,112
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TDA8763M/4/C4,118
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TDA8763AM/3/C4
✅ 드롭인✓ 재고 있음
$6.5 / 개
데이터시트 보기 →TDA8763M/4/C4 최대 정격 & 전기적 특성
| 분해능 | 10 bit |
| 샘플링 속도 | 40 MSPS |
| Number of Channels | 1 |
| Architecture | Sigma-Delta |
| Input Type | Single-ended |
| Output Interface | Parallel |
| 패키지 | 28-pin SSOP |
| 실장 유형 | Surface Mount |
| Reference Type | Internal reference regulator |
| Power Consumption | Low-power (per datasheet title) |
| Terminal Form | GULL WING |
| Terminal Count | 28 |
| Package Code | SSOP |
| Package Shape | RECTANGULAR |
| Temperature Grade | INDUSTRIAL |
TDA8763M/4/C4 rectangular 핀 구성 가이드
TDA8763M/4/C4(rectangular 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: TDA8763M/4/C4.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TDA8763M/4/C4 적합 용도: 6 애플리케이션s: Industrial Process Control Data Acquisition, Medical Instrumentation Signal Chain, CCD Imaging Digitizers, Intermediate Frequency (IF) Digitization, Portable Test and Measurement Equipment, Video Signal Processing Front-Ends.
Industrial Process Control Data Acquisition
The TDA8763M/4/C4 suits industrial process-control digitizers that require 10-bit resolution at moderate bandwidths. Its 40 MSPS sigma-delta architecture oversamples the transducer signal, allowing an external simple anti-aliasing filter while the integrated decimator produces a clean in-band digital word. The internal reference regulator stabilizes DC accuracy against supply drift on factory-floor rails. Place the ADC after instrumentation amplifiers and add 100 nF + 10 uF decoupling on AVDD and DVDD. Trade-off: sigma-delta latency is higher than SAR, so it is best for continuous monitoring rather than closed-loop control loops.
추천
Medical Instrumentation Signal Chain
In medical instrumentation front-ends such as ultrasound receivers and patient-monitoring digitizers, the TDA8763M/4/C4's 10-bit resolution and 40 MSPS oversampling deliver sufficient dynamic range for demodulated biosignals. The sigma-delta modulator's noise-shaping pushes quantization noise out of the signal band, improving SNR where small analog amplitudes matter. The integrated reference regulator reduces BOM count, valuable for cost-sensitive single-use medical devices. Designers should still characterize leakage and PSRR across the medical EMC environment, and add ferrite beads on supply lines. Compared with SAR ADCs, this part favors bandwidth over absolute conversion latency.
추천
CCD Imaging Digitizers
The TDA8763M/4/C4 can digitize CCD video output streams in imaging subsystems where 10-bit intensity resolution at moderate pixel rates is acceptable. Its parallel 10-bit output bus simplifies connection to a frame-grabber FPGA or ASIC, and the 40 MSPS sampling rate supports standard VGA-class video bandwidths. The internal reference regulator eases thermal drift concerns in long-exposure applications. Place the ADC close to the CCD analog output to minimize trace capacitance, and use ground guarding on the parallel digital output side. Modern CMOS image sensors typically integrate ADCs, so this use case applies to legacy CCD modules.
추천
Intermediate Frequency (IF) Digitization
Communications IF stages benefit from the TDA8763M/4/C4's combination of 40 MSPS sampling and sigma-delta noise shaping. Oversampling the IF signal by a wide margin allows digital downconversion and filtering in software or FPGA fabric, eliminating multiple analog mixer stages. The 10-bit resolution is sufficient for demodulating narrow-band signals with moderate SNR requirements, including AM/FM audio recovery and digital-modulation pre-processing. Ensure the analog input common-mode voltage is within the device's specified range and that the clock jitter remains below the sigma-delta modulator's tolerance for in-band SNR.
추천
Portable Test and Measurement Equipment
Handheld oscilloscopes, spectrum analyzers, and field-test instruments leverage the TDA8763M/4/C4's low-power 10-bit conversion and integrated reference for compact, battery-friendly designs. The 28-SSOP package fits small PCBs, while the parallel output allows direct capture by an FPGA or microcontroller DMA channel. The internal reference regulator removes one external component, helping extend battery life and reducing warm-up drift. Trade-off: 10 bits limits dynamic range versus 12/14-bit modern alternatives, so engineers targeting higher SNR should evaluate current-generation SAR ADCs for new portable designs.
추천
Video Signal Processing Front-Ends
The TDA8763M/4/C4 fits legacy video front-ends that require 10-bit pixel or component-video digitization at up to 40 MSPS. The parallel output bus reduces glue logic between the ADC and a video processor or frame buffer. The sigma-delta architecture provides inherent anti-aliasing through oversampling, simplifying the analog input filter. Designers should still add line-driver buffering ahead of the ADC input and maintain controlled-impedance routing for the parallel output to limit crosstalk. Modern HDMI/DVI digitizers typically use dedicated video ADCs, but this part remains relevant for industrial and broadcast video output.
추천
추천 제품 요약
엔지니어링 참조 데이터: TDA8763M/4/C4 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | TDA8763M/4/C4,112 | TDA8763M/4/C4,118 | TDA8763AM/3/C4 |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
| Architecture | Sigma-Delta | Sigma-Delta | Sigma-Delta | Sigma-Delta (same family) |
| Number of Channels | 1 | 1 | 1 | 1 (same family) |
| Output Interface | Parallel | Parallel | Parallel | Parallel (same family) |
| Reference Type | Internal regulator | Internal regulator | Internal regulator | Internal regulator (same family) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete (family) |
| Temperature Grade | Industrial | Industrial | Industrial | Industrial (family) |
주요 차별점
- Integrated internal reference regulator eliminates external reference IC (vs TDA8763AM/3/C4)
- Higher 40 MSPS sampling rate versus typical 10-bit SAR ADCs at 20 MSPS (vs ADS8319 (TI))
- Parallel 10-bit output simplifies digital interface (vs AD9201 (ADI))
설계 노트
The TDA8763M/4/C4 requires separate analog (AVDD) and digital (DVDD) supply rails. Place a 10 uF bulk capacitor and a 100 nF ceramic decoupling capacitor as close as possible to each supply pin. Use a ferrite bead or small inductor between AVDD and DVDD to isolate digital switching noise from the analog reference. Power-rail sequencing is recommended so that AVDD rises before DVDD to avoid latch-up at startup.
Route the parallel 10-bit digital output bus with matched trace lengths and a continuous ground plane underneath. Add series damping resistors (22-33 ohm) near the ADC output pins to limit edge rates and reduce crosstalk into the analog input. Keep the analog input trace short and guarded with ground pours on both sides to minimize coupling from the parallel digital bus.
Do not exceed the analog input common-mode voltage range or apply signals before power-up. Ensure the sample clock source has low jitter (<50 ps RMS) to preserve in-band SNR of the sigma-delta modulator. The internal reference regulator still requires a low-ESR bypass capacitor at the REF pin - omitting it degrades DC accuracy and increases low-frequency noise.
규정 준수 정보
Compliance status not present in the Verified Web Data. The part was released in 1999 (IC02 datasheet revision) before modern RoHS/REACH certifications were standard; consult NXP for current compliance statements.