THS1215CPW - 12-Bit 15 MSPS ADC | Texas Instruments
부품 번호: THS1215CPW ✓ 활성THS1215CPW 개요
An ADC is an analog-to-digital converter, a data-acquisition IC that samples a continuous voltage and converts it into a numeric code. The THS1215CPW belongs to the pipelined ADC family, whose internal stages permit high conversion throughput while the final digital result is transferred through a parallel interface. Its position in the hierarchy is analog-to-digital converter → data-converter IC → signal-chain component, with the digital output intended for capture by an FPGA, DSP, microcontroller, or other digital processing system.
The principal specifications are 12-bit nominal resolution, a 15 MSPS maximum sampling rate, one analog input, and a 3.3 V operating supply. The manufacturer describes the device as a low-power ADC with power-down support, making it useful when acquisition duty cycle is below 100%. These values establish the part as a general-purpose high-speed sampler rather than a low-resolution slow ADC or a very-high-resolution waveform converter.
The 28-pin TSSOP package supports compact PCB layouts while exposing the converter's digital and control connections. Because a parallel ADC can produce a new 12-bit code every 66.7 ns at 15 MSPS, timing margins, output loading, clock quality, and PCB routing become important design considerations. The THS1215CPW uses a 3.3 V supply, so the digital interface, analog input range, clock amplitude, and downstream logic levels must all be evaluated together before finalizing the system power architecture.
Typical uses include industrial instrumentation, communications receivers, radar or sonar signal chains, medical monitoring, test and measurement equipment, and embedded control systems that need periodic high-speed sampling. In each case, the ADC can serve as the front-end conversion stage, while a processor evaluates the resulting samples for filtering, thresholding, demodulation, feature extraction, or closed-loop control.
Design the analog input path around the manufacturer's recommended source impedance and capacitor configuration. Keep the clock and parallel data traces short, provide a low-impedance reference and clean supply connections, and account for acquisition settling between samples. Paydown can reduce consumption between bursts, but the required enable timing and valid-data latency should be verified against the system control sequence.
This page organizes the THS1215CPW's core specifications, same-footprint alternatives, interface considerations, and application guidance into a practical engineering reference. It also distinguishes verified device identity and packaging from parameters that require confirmation in the manufacturer datasheet before a new PCB or production release is approved.
드롭인 대체품: THS1215CPW — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: THS1215CPW (동일 폼 팩터 및 풋프린트) — 차이점: Package, RoHS Status, Supply Voltage, Resolution, Architecture.
THS1215CPWRG4
✅ 드롭인가격 문의
데이터시트 보기 →THS1215CPWG4
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
THS1215CPWRG4
✅ 드롭인가격 문의
데이터시트 보기 →THS1215IPWG4
✅ 드롭인가격 문의
데이터시트 보기 →THS1215IPWRG4
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
THS1215CPW 최대 정격 & 전기적 특성
| Converter Type | Pipelined analog-to-digital converter |
| 분해능 | 12 bit |
| 샘플링 속도 | 15 MSPS |
| Number of Analog Inputs | 1 input |
| Output Interface | Parallel output |
| 공급 전압 | 3.3 V |
| Power-Down Function | Supported |
| 패키지 | 28-pin TSSOP |
| Package Code | PW |
| Terminal Count | 28 terminals |
| Package Shape | Rectangular |
| 실장 유형 | Surface mount |
| Temperature Grade | Commercial |
| Analog Input Sampling Rate | 15 MSPS |
| RoHS 상태 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
THS1215CPW rectangular 핀 구성 가이드
THS1215CPW(rectangular 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: THS1215CPW.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
THS1215CPW 적합 용도: 6 애플리케이션s: Industrial Process Instrumentation, Communications Receiver, Radar and Sonar Signal Acquisition, Medical Monitoring Equipment, Test and Measurement Instrumentation, Embedded Control and Data Logging.
Industrial Process Instrumentation
The THS1215CPW can serve as the high-speed conversion stage in industrial measurement systems that need to capture changing analog sensor or control signals. Its 12-bit resolution provides 4,096 numerical codes per conversion, while 15 MSPS permits rapid sampling of waveforms, vibration, or transient events. The 3.3 V architecture also integrates naturally with modern low-voltage control electronics. Place the ADC behind the manufacturer's recommended input-conditioning network, provide a clean reference and supply, and verify the selected ordering option against the equipment's ambient-temperature requirements. Power-down can be useful in portable or duty-cycled instruments, although wake-up timing should be included in the acquisition-control sequence.
추천
Communications Receiver
A communications receiver can use the THS1215CPW to digitize intermediate-frequency or other bounded analog signals before digital filtering and demodulation. The device's 15 MSPS throughput gives the design a 66.7 ns maximum sampling interval, which is useful when the channel waveform contains timing information that must be retained. Its 12-bit parallel output can connect directly to a processor or FPGA input bank, subject to the clock and data-timing requirements in the manufacturer datasheet. The single analog input keeps the pin count and board area manageable for compact receiver boards. Clock jitter, input bandwidth, reference stability, and digital output timing require particular attention in high-frequency communication designs.
추천
Radar and Sonar Signal Acquisition
The THS1215CPW is appropriate for radar, sonar, and other broadband signal-acquisition front ends where the analog waveform must be converted into parallel digital samples for later processing. A 15 MSPS conversion rate supports sampling of substantially faster events than a conventional slow instrumentation converter, while 12-bit resolution balances data volume against signal detail. In such systems, the ADC should be placed after a low-noise amplifier, anti-alias filter, and controlled-impedance input network. Designers should minimize loop area, preserve a continuous return path, and match clock and data trace lengths as far as practical. The datasheet's input range, acquisition time, and signal-to-noise characteristics should govern the actual bandwidth and dynamic-range design.
추천
Medical Monitoring Equipment
The THS1215CPW can support acquisition stages in medical monitoring and diagnostic equipment that capture rapidly varying analog waveforms. The 12-bit, 15 MSPS combination provides a practical balance between temporal resolution and parallel-output simplicity, allowing samples to be transferred to an FPGA or embedded processor for filtering and analysis. Because medical designs may impose strict safety, electromagnetic-interference, and calibration requirements, the ADC must be evaluated within the complete signal chain rather than selected from conversion rate alone. Confirm operating-temperature limits, analog performance, lifecycle status, and applicable quality documentation from the manufacturer. A low-noise input amplifier, controlled reference, and carefully decoupled 3.3 V supply are essential to preserve measurement integrity.
추천
Test and Measurement Instrumentation
The THS1215CPW is useful in oscilloscope-like, automated test, and signal-analysis equipment that needs to sample an analog input and present a parallel digital stream to a processor. At 15 MSPS, the converter can capture waveform details that general-purpose MCU ADC channels cannot resolve, while 12-bit output reduces the storage and transfer burden relative to a higher-resolution converter. For a new instrument, use the manufacturer's recommended driver and reference topology, and keep the analog and digital return currents separated to reduce conversion-error coupling. The parallel bus should be routed according to the published timing specification. Power-down is valuable in instruments that spend substantial time idle or between automated test cycles.
추천
Embedded Control and Data Logging
An embedded control system can use the THS1215CPW when an analog waveform must be sampled faster than the internal ADC of a microcontroller can support. The 12-bit parallel results can be latched by an FPGA, DSP, or suitable microcontroller logic, enabling filtering, peak detection, or control-loop updates without imposing a high-speed serial-converter interface on the processor. The 3.3 V supply supports integration with contemporary embedded logic, but level compatibility and timing margin must be checked carefully. Power-down allows the acquisition path to remain inactive during long control intervals. Before implementation, verify the converter's input range and acquisition requirements against the transducer or actuator interface, and add the manufacturer-recommended bypass and reference-decoupling network.
추천
추천 제품 요약
엔지니어링 참조 데이터: THS1215CPW — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | THS1215CPWRG4 | THS1215CPWG4 | THS1215CPWR | THS1215IPW | THS1215IPWRG4 |
|---|---|---|---|---|---|---|
| Package | 28-pin TSSOP | 28-pin TSSOP - same | 28-pin TSSOP - same | 28-pin TSSOP - same | 28-pin TSSOP - same | 28-pin TSSOP - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| ADC Architecture | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Sampling Rate | 15 MSPS | 15 MSPS | 15 MSPS | 15 MSPS | 15 MSPS | 15 MSPS |
| Analog Input Count | 1 input | 1 input | 1 input | 1 input | 1 input | 1 input |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Output Interface | Parallel | Parallel | Parallel | Parallel | Parallel | Parallel |
| Power-Down Function | Supported | Supported | Supported | Supported | Supported | Supported |
| Ordering-Specific Conditions | Commercial grade; full ordering details require confirmation | RG4 suffix conditions require confirmation | G4 suffix conditions require confirmation | R suffix conditions require confirmation | I suffix conditions require confirmation | IPWRG4 suffix conditions require confirmation |
주요 차별점
- Documented same-family replacement path (vs THS1215CPWRG4)
- Single-input pipelined conversion at 15 MSPS (vs THS1215IPW)
- Compact 28-pin TSSOP implementation (vs THS1215CPWR)
설계 노트
Route the 12-bit parallel output conservatively because a new conversion can occur every 66.7 ns at 15 MSPS. Use the manufacturer timing diagram to establish setup and hold margins, keep the bus traces short, provide a continuous ground reference, and avoid stubs or test-point structures that materially change loading. Confirm the receiving FPGA or processor voltage levels and interface timing against the THS1215CPW datasheet before finalizing the parallel bus topology.
Implement the analog input as a controlled-impedance path rather than directly connecting a high-impedance sensor to the converter. Use the manufacturer's recommended series-resistance and charge-injection capacitor arrangement to promote acquisition settling, and place the network close to the ADC pins. The available listing confirms the 15 MSPS rate but not the permitted source impedance, so calculate settling from the datasheet's acquisition-time, input-capacitance, and switch-resistance values.
Separate analog and digital return currents where possible and follow the manufacturer's reference and bypass-capacitor layout. The THS1215CPW operates from 3.3 V, and reference or supply disturbance can appear directly as conversion error. Keep switching regulators and high-current digital paths away from the input and reference nodes, and use separate ground-plane connections that join at a controlled point near the power entry and analog return.
Do not treat equal resolution and sampling rate as sufficient proof that every ordering suffix is interchangeable. Before replacing THS1215CPW, compare the manufacturer ordering table for temperature grade, package shipping method, qualification status, and lifecycle status. Also verify that the replacement uses the same 28-pin TSSOP footprint and that all clock, reference, control, and parallel-output functions are assigned identically on the PCB.
규정 준수 정보
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for this exact ordering configuration. Confirm environmental and quality compliance with the manufacturer before production release.