TJA1041AT/V - 1Mbit/s High-Speed CAN Transceiver | NXP
부품 번호: TJA1041AT/V ✗ 단종TJA1041AT/V 개요
A CAN transceiver is an interface IC within the broader Controller Area Network hierarchy. A CAN controller generates and interprets digital protocol frames, while the physical-layer transceiver converts controller signals into a differential CAN bus waveform and converts received bus levels back into logic-compatible receive data. The TJA1041AT/V therefore belongs to the CAN transceiver family, which operates at the physical-bus layer beneath communication controllers, embedded processors, and complete automotive electronic control units.
Key operating features include support for high-speed CAN communication up to 1 Mbit/s, a 4.75 V minimum operating supply, a 5.25 V maximum operating supply, differential bus transmission, and differential bus reception. Its transceiver architecture allows a host controller to remain separate from the physical bus wiring while providing the electrical interface required for multi-node communication. The 14-pin SO package supports compact surface-mount assembly in automotive control-unit designs.
The TJA1041A family is associated with ISO 11898 high-speed CAN communication and provides compatibility with CAN protocol controllers that provide TXD and RXD logic signals. The CANH and CANL connections carry complementary differential bus levels. This differential signaling improves common-mode noise rejection in vehicle electrical environments, where switching loads, alternator systems, and other transient-producing equipment can disturb the communication network.
Typical applications include automotive body-control modules, powertrain controllers, gateway units, dashboard electronics, seat and door modules, lighting controllers, small electric motors, and industrial or transportation equipment using a CAN bus. In these systems, the transceiver is placed between the host CAN controller and the CANH and CANL network conductors. PCB routing, termination, grounding, and protection remain critical because the transceiver is only one element of the complete physical-layer network.
Design the power and signal paths carefully around the 4.75 V to 5.25 V operating range. Decoupling should be placed close to the supply pins, the CANH and CANL traces should follow controlled-impedance routing practices, and the bus should use the termination strategy specified by the CAN network design. Protection components may be added when the cable environment includes severe automotive transients, provided their capacitance and clamping behavior do not distort the differential signal.
This product page combines the NXP technical description with lifecycle information, package identification, practical interface guidance, sourcing questions, and clearly qualified replacement analysis. It also highlights where an existing design can be reused and where a new PCB and EMC validation are required before changing CAN transceivers.
드롭인 대체품: TJA1041AT/V — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
TJA1041AT
✅ 드롭인가격 문의
데이터시트 보기 →TJA1041
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TJA1041AT/CM,118
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TJA1041AT/V 사양
| Product Type | High-speed CAN transceiver |
| Maximum CAN Data Rate | 1 Mbit/s |
| Minimum Operating Supply Voltage | 4.75 V |
| Maximum Operating Supply Supply Voltage | 5.25 V |
| Bus Interface | Differential CANH and CANL |
| Transmit Capability | Differential |
| Receive Capability | Differential |
| Protocol Controller Interface | TXD and RXD logic signals |
| Primary Application | Automotive high-speed CAN nodes |
| 패키지 | 14-pin SO surface-mount package |
| 실장 유형 | Surface mount |
| CAN Transceiver Type | Half CANbus transceiver |
| 수명 주기 상태 | End of Life |
| Manufacturer | NXP Semiconductors |
TJA1041AT/V 14-pin so surface-mount package 핀 구성 가이드
TJA1041AT/V(14-pin so surface-mount package 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: TJA1041AT/V.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TJA1041AT/V 적합 용도: 6 애플리케이션s: Automotive Body Control Module, Vehicle Gateway and Communication Node, Dashboard and Instrument Cluster Electronics, Door, Seat, and Lighting Controller, Powertrain and Chassis Electronics, Industrial and Transportation CAN Equipment.
Automotive Body Control Module
The TJA1041AT/V fits an automotive body-control module because it connects a CAN controller to a differential CANH and CANL network at data rates up to 1 Mbit/s. Its 4.75 V to 5.25 V operating range aligns with a regulated 5 V vehicle electronics rail. Place the transceiver beside the controller and preserve short, symmetric bus routing so the differential signal retains low distortion. The primary design trade-off is that the part is marked End of Life, so production planning should include a controlled migration and last-time-buy assessment rather than treating new design adoption as risk-free.
추천
Vehicle Gateway and Communication Node
A gateway or communication node can use the TJA1041AT/V as the physical-layer interface between its host controller and the vehicle CAN backbone. Differential transmit and receive capability supports communication at up to 1 Mbit/s, while the 5 V supply range suits regulated controller electronics. The transceiver should be positioned near the bus connector and protection network to minimize trace sensitivity. Because the family is End of Life, new gateway programs should evaluate a current replacement early enough to allow PCB routing, EMC, and network timing changes without rushing production validation.
추천
Dashboard and Instrument Cluster Electronics
The TJA1041AT/V is suitable for dashboard electronics that exchange control, status, and diagnostic frames over a high-speed CAN network. Its operation up to 1 Mbit/s provides sufficient physical-layer bandwidth, and differential signaling helps reject common-mode noise present in vehicle harnesses. Route CANH and CANL as a matched pair, place filtering close to the connector, and maintain the grounding arrangement required by the reference design. The key sourcing limitation is lifecycle status: NXP marks the TJA1041AT family as End of Life, making component continuity and last-time-buy planning essential.
추천
Door, Seat, and Lighting Controller
Compact door, seat, or lighting modules can use the TJA1041AT/V when their controller needs a reliable high-speed differential CAN interface. The 14-pin SO package supports surface-mount assembly, and the 4.75 V to 5.25 V range is compatible with regulated 5 V module electronics. Keep the bus pair away from relay drivers, motor outputs, and switching-power nodes to reduce coupling. For a new platform, the End of Life designation is a material constraint; for an existing platform, verify the exact ordering suffix, stock position, and any approved migration before committing new production volumes.
추천
Powertrain and Chassis Electronics
The TJA1041AT/V can support CAN communication in powertrain or chassis electronics when the network operates at the high-speed CAN rate of up to 1 Mbit/s. Differential bus signaling helps maintain data integrity in an electrical environment containing relays, solenoids, and switching transients. The design should include appropriate bus protection and maintain the transceiver's recommended ground and layout relationships. Engineers must also verify the exact suffix's temperature and qualification requirements, as the manufacturer identifies the TJA1041AT family as End of Life and does not establish every qualification parameter in the product summary.
추천
Industrial and Transportation CAN Equipment
Industrial controllers, transportation equipment, and embedded monitoring systems can use the TJA1041AT/V when they already employ the NXP 14-pin SO high-speed CAN interface. The device provides differential transmit and receive functions at up to 1 Mbit/s and operates from 4.75 V to 5.25 V, allowing reuse of established 5 V power architecture and PCB routing. Controlled-impedance bus routing and correct termination remain necessary for dependable operation. For new equipment, compare current alternatives and plan validation because the end-of-life designation makes long-term availability uncertain.
추천
추천 제품 요약
엔지니어링 참조 데이터: TJA1041AT/V — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | TJA1041AT | TJA1041 | TJA1041AT/CM,118 |
|---|---|---|---|---|
| Package | SO-14 | SO-14 | SO-14 | 14-SO |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | Half CANbus transceiver |
| Minimum Operating Supply Voltage | 4.75 V | 4.75 V | 4.75 V | 4.75 V |
| Maximum Operating Supply Voltage | 5.25 V | 5.25 V | 5.25 V | 5.25 V |
주요 차별점
- Direct retention of the established NXP TJA1041AT interface (vs TJA1041AT)
- Same core physical-layer performance as the original family member (vs TJA1041)
- Documented standby and sleep functionality in the listed ordering option (vs TJA1041AT/CM,118)
설계 노트
Route CANH and CANL as a tightly coupled differential pair and keep the pair continuous across layers. Place the transceiver close to the CAN controller, while placing connector-side protection near the external pins. Maintain the ground and return-path arrangement shown in the NXP datasheet so common-mode and transient energy does not disrupt the differential receiver.
Provide a regulated 5 V supply that remains between the device's 4.75 V and 5.25 V operating limits. Place the required decoupling capacitors close to the supply and ground terminals with short return paths. Do not add bulk capacitance directly across CANH and CANL; excessive bus capacitance can reduce signal integrity and prevent reliable operation at the intended network bit rate.
Do not substitute the transceiver solely because the device names are similar. Confirm package dimensions, terminal numbering, supply requirements, standby or sleep behavior, temperature grade, and the exact ordering suffix before replacing TJA1041AT/V. The NXP page identifies an End of Life condition, so the exact variant, last-time-buy status, and approved migration should be documented before production approval.
Keep the CAN bus pair away from relay coils, motor windings, switching-regulator switches, and high-di/dt nets. Use the termination strategy required by the complete CAN topology rather than adding local resistors that could create incorrect bus impedance. Validate radiated and conducted emissions in the final enclosure and harness configuration because the transceiver alone cannot guarantee system-level EMC compliance.
규정 준수 정보
The manufacturer product page confirms an End of Life overview and shipping-discontinuance information but does not establish the requested compliance values. Check the exact ordering code with NXP before production release.