TLE6250PG - 1Mbaud CAN Transceiver | Infineon | DSO-8
부품 번호: TLE6250PG ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
TLE6250PG 개요
A CAN transceiver is an interface IC that converts logic-level transmit and receive signals into physical bus signals, then converts received bus states back into controller-compatible logic. In the product hierarchy, the TLE6250PG belongs to CAN transceivers, interface transceivers, interface ICs, and semiconductors. This position places it between a CAN controller or microcontroller and the differential CAN bus wiring.
Key characteristics include one transmitter and one receiver, operation up to 1 Mbaud, a nominal 5 V supply range of 4.5 V to 5.5 V, and compatibility with high-speed CAN systems. The PG version is supplied in the compact DSO-8 outline identified by DigiKey as PG-DSO-8-16. The verified product listings also describe a cut-tape package option for TLE6250PG and identify it as a standard high-speed CAN interface IC.
The transceiver separates the controller-side digital domain from the bus-side differential domain. Its TXD input accepts the controller's transmit command, while RXD provides the controller with a received bus state. STB provides standby control, and the remaining bus-side and supply pins connect the device to the CANH and CANL network. This division of responsibilities allows a host processor to use ordinary CMOS-compatible I/O while the transceiver handles the physical CAN bus levels.
Typical applications include automotive body and comfort electronics, industrial automation controllers, CAN-connected sensors, engine-control modules, diagnostic equipment, and embedded CAN gateways. The 1 Mbaud rate is suitable for high-speed control and diagnostic networks, although actual bus length, termination, topology, and propagation delay must be considered when selecting cable length and bit rate.
For PCB design, place the transceiver close to the CAN connector and preserve short, symmetrical CANH and CANL routing. Use the application information in the Infineon TLE6250 datasheet for decoupling and termination values. Avoid long stubs, maintain the required 120 ohm bus termination at both physical ends, and provide adequate creepage and clearance where automotive vibration, temperature, or transient requirements apply.
This page consolidates verified manufacturer and distributor information, explicit data gaps, package details, sourcing links, and application guidance. It also distinguishes the TLE6250PG from related TLE6250 variants so engineers can verify standby, wake-up, and pin-level differences before committing a design to production.
드롭인 대체품: TLE6250PG — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: TLE6250PG (동일 폼 팩터 및 풋프린트) — 차이점: Package, Product Type, RoHS Status, Operating Temperature Range, Packaging.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
TLE6250G
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
SN75176BD
✅ 드롭인✓ 재고 있음
$0.1501 / 개
데이터시트 보기 →SN65HVD3082EDR
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →TJA1021T/20/C
✅ 드롭인✓ 재고 있음
$0.45 / 개
데이터시트 보기 →KSZ8001LI
✅ 드롭인✓ 재고 있음
$4.3 / 개
데이터시트 보기 →TLE6250PG 사양
| Product Type | 1/1 CAN transceiver |
| Protocol | High-speed CAN |
| Maximum Data Rate | 1 Mbaud |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| System Compatibility | ISO 11898 |
| Standby Support | Yes |
| 패키지 | 8-SOIC (DSO-8) |
| Package Code | PG-DSO-8-16 |
| Packaging | Cut Tape (CT) |
| 실장 유형 | Surface mount |
| Automotive Qualification | AUTO |
| RoHS 상태 | RoHS-compliant |
| Lead-Free Finish | Pb-free |
| Soldering Standard | IPC/JEDEC J-STD-020 |
TLE6250PG pg-dso-8-16 핀 구성 가이드
TLE6250PG(pg-dso-8-16 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: TLE6250PG.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TLE6250PG 적합 용도: 6 애플리케이션s: Automotive Body Control Module, Industrial CAN Automation Controller, CAN-Connected Sensor Node, Vehicle Diagnostic Gateway, Engine or Powertrain Control Unit, Embedded CAN-to-Serial Gateway.
Automotive Body Control Module
The TLE6250PG fits an automotive body-control module that connects door, lighting, climate, and seat electronics over a high-speed CAN network. Its 1 Mbaud capability supports responsive control traffic, while the 4.5 V to 5.5 V supply range aligns with a regulated 5 V controller rail. The 8-pin DSO package also conserves board area compared with larger transceivers. The transceiver is normally placed between the host CAN controller and CANH/CANL connector pins. Before production release, verify the exact operating-temperature range, ISO version, wake-up behavior, and automotive qualification evidence because those details are not quantified in the supplied snippets.
추천
Industrial CAN Automation Controller
The TLE6250PG is suitable for an industrial automation controller that exchanges commands and sensor status with remote actuator modules over high-speed CAN. A 1 Mbaud link reduces message-transfer time compared with lower-rate CAN networks, while the single transmitter and single receiver provide the physical interface required for a conventional CAN node. The controller-side TXD and RXD signals connect directly to a CAN-capable microcontroller, and the bus-side connections terminate at the network connector. Keep the transceiver close to that connector and use a symmetric CANH/CANL route to reduce sensitivity to board-level differences.
추천
CAN-Connected Sensor Node
The TLE6250PG can interface a compact sensor node that publishes measurements over a shared high-speed CAN bus. The 1 Mbaud rate supports timely updates, and the 4.5 V to 5.5 V operating range is compatible with a regulated 5 V sensor-platform supply. Because the DSO-8 outline limits PCB area, it is useful in distributed monitoring equipment where multiple nodes are mounted in small enclosures. Preserve a short differential path from the transceiver to the connector, fit bus termination according to the complete network topology, and confirm that standby or bus-inhibit behavior matches the node's power-management strategy.
추천
Vehicle Diagnostic Gateway
The TLE6250PG is applicable to a diagnostic gateway that bridges a vehicle CAN network to another controller or communication domain. Supporting 1 Mbaud allows the gateway to participate in high-speed diagnostic and vehicle-service traffic, while the 8-pin DSO-8 package supports compact electronics. The host controller drives TXD and reads RXD, allowing the gateway to participate in standard CAN arbitration and acknowledgment. Because diagnostic links may be temporarily connected to test equipment, cable length, termination, fault tolerance, and mode behavior should be reviewed against the official datasheet and the final vehicle network specification.
추천
Engine or Powertrain Control Unit
The TLE6250PG can serve as the CAN physical interface in an engine or powertrain control unit when the system operates at 1 Mbaud and uses a 5 V transceiver domain. Fast bus access helps coordinate time-sensitive actuator commands, while the 1/1 transmitter-receiver arrangement fits a standard CAN node. The device should be positioned near the protected harness connector, with CANH and CANL routed as a controlled differential pair. The verified listing identifies automotive usage, but engineers must still confirm temperature limits, transient immunity, bus fault behavior, and exact qualification documentation before using it in a safety-relevant powertrain design.
추천
Embedded CAN-to-Serial Gateway
The TLE6250PG is useful in a compact embedded gateway that carries CAN traffic between a microcontroller and an external bus connector. The 1 Mbaud rate and 4.5 V to 5.5 V supply range support conventional controller interfaces, while standby support can assist systems that need a low-power operating state. Place the transceiver near the connector and keep TXD and RXD traces away from CANH and CANL to reduce coupling. The design must define startup, sleep, and wake-up behavior explicitly, especially if the host firmware changes the STB state during communications or fault recovery.
추천
추천 제품 요약
엔지니어링 참조 데이터: TLE6250PG — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | TLE6250G | SN75176BD | SN65HVD3082EDR | TJA1021T/20/C | KSZ8001LI |
|---|---|---|---|---|---|---|
| Package | DSO-8 | DSO-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | Infineon Technologies | Infineon Technologies | Texas Instruments | Texas Instruments | NXP Semiconductors | Microchip Technology |
주요 차별점
- Directly identified 1 Mbaud high-speed CAN operation (vs SN75176BD)
- Same-manufacturer family alternative with matching DSO-8 format (vs TLE6250G)
- Documented lead-free environmental construction (vs TJA1021T/20/C)
설계 노트
Place the TLE6250PG near the CAN connector and route CANH and CANL as a short differential pair on the same PCB reference plane. Minimize vias, stubs, and impedance discontinuities, and keep the pair away from switching nodes and noisy clocks. The verified data does not provide exact layout dimensions or differential-impedance targets, so use the layout and termination guidance in the Infineon TLE6250 datasheet rather than relying on generic values.
Do not treat an 8-pin package match as proof of functional interchangeability. The verified comparison indicates that TLE6250G differs from TLE6250PG in standby and wake-up-related behavior, and the other listed alternatives lack verified pinout and mode-control comparisons. Before substitution, compare TXD and RXD polarity, STB truth table, bus-bias behavior, input thresholds, bus fault handling, and whether the external controller relies on INH or another mode-control signal.
Provide a clean regulated supply within the verified 4.5 V to 5.5 V operating range and decouple it close to the transceiver. Apply the manufacturer datasheet's recommended capacitance and ESR limits rather than choosing a generic bulk value without checking them. Confirm supply ripple, startup sequencing, and standby current in the final controller design; the supplied snippets do not quantify quiescent or standby current, so those values must be obtained from the official datasheet.
A 1 Mbaud rating does not guarantee 1 Mbaud operation over every cable length or topology. Verify propagation delay, node count, termination, stub length, common-mode margin, and controller timing against the network specification. In a conventional CAN network, install 120 ohm termination at each end of the main bus, but split termination may be needed for long or split networks and should be validated in the complete topology.
규정 준수 정보
The official Infineon datasheet identifies TLE6250PG as a green RoHS-compliant product with a Pb-free lead finish and suitability for Pb-free soldering according to IPC/JEDEC J-STD-020. The supplied data does not establish REACH, AEC-Q100, halogen-free, or conflict-minerals status.
