TLE8250VSJXUMA1 - 2Mbps CAN Transceiver | Infineon
부품 번호: TLE8250VSJXUMA1 ✓ 활성TLE8250VSJXUMA1 개요
A CAN transceiver is an interface IC that converts logic-level signals between a host controller and a differential CAN bus. In the complete communication hierarchy, this component belongs to the CAN physical-layer transceiver class, where it interfaces a CAN controller or microcontroller with the CAN_H and CAN_L bus conductors. Its role is to provide bus-compatible signal levels while supporting reliable communication across a multi-node network.
The principal operating characteristics include the 4.5 V to 5.5 V supply range, 2 Mbps maximum CAN data rate, and -40°C to +150°C operating-temperature range. The PG-DSO-8-16 package supports compact surface-mount PCB construction, while the extended temperature rating supports use in automotive electronics, industrial controllers, vehicle networking equipment, and embedded CAN systems.
The Infineon ordering designation identifies this unit as the TLE8250VSJXUMA1 configuration in an 8-pin package. Its CANbus protocol designation and high-speed data capability distinguish it from low-speed fault-tolerant transceivers and from controller-only CAN devices. When designing around this component, the system supply must remain within 4.5 V to 5.5 V, and the PCB must implement the device-specific termination, bus-interface, ground, and decoupling connections shown in the Infineon datasheet.
Typical uses include automotive body and comfort electronics, industrial CAN gateways, vehicle diagnostic interfaces, distributed automation nodes, and embedded control systems. A microcontroller with an integrated CAN controller can communicate through the transceiver, while the differential bus provides noise-resistant signaling over cables between distributed modules. The 2 Mbps rate is suitable for high-throughput control and diagnostic traffic.
Layout quality is critical in CAN networks. Place the device and its decoupling capacitor close to their associated supply pins, keep the CAN_H and CAN_L routing symmetrical, provide a continuous ground reference, and follow the recommended common-mode choke or split termination approach for the target network. Bus protection should be selected according to the vehicle or industrial environment rather than inferred solely from transceiver specifications.
This product record combines the manufacturer's identified CANbus function, 2 Mbps data rate, 4.5 V to 5.5 V supply range, extended temperature range, package information, and RoHS marking with practical guidance for PCB implementation, network integration, sourcing, and drop-in replacement assessment.
드롭인 대체품: TLE8250VSJXUMA1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청TLE8250VSJXUMA1 사양
| Device Type | CAN bus transceiver |
| Protocol | CANbus |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Maximum Data Rate | 2 Mbps |
| 동작 온도 범위 | -40°C to +150°C |
| Manufacturer Package | PG-DSO-8-16 |
| Package Type | 8-SOIC |
| 핀 수 | 8 pins |
| 실장 유형 | Surface mount |
| RoHS 상태 | Compliant |
| Number of Transceivers | 1 transceiver |
TLE8250VSJXUMA1 8-soic 핀 구성 가이드
TLE8250VSJXUMA1(8-soic 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: TLE8250VSJXUMA1.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TLE8250VSJXUMA1 적합 용도: 6 애플리케이션s: Automotive Body Control Network, Vehicle Diagnostic Gateway, Industrial CAN Gateway, Distributed Automation Node, Embedded CAN Communication Module, Robotic Control Network.
Automotive Body Control Network
The TLE8250VSJXUMA1 fits an automotive body-control node that exchanges commands between a CAN controller and distributed vehicle modules. Its 2 Mbps maximum data rate provides adequate bandwidth for diagnostic and control traffic, while the 4.5 V to 5.5 V supply aligns with common 5 V vehicle electronics. The -40°C to +150°C operating range supports harsh cabin and body-compartment conditions when the qualification requirements of the complete vehicle program are satisfied. Place the transceiver near the bus entry, use the recommended supply decoupling, and route CAN_H and CAN_L as a matched pair to preserve differential signal quality.
추천
Vehicle Diagnostic Gateway
A diagnostic gateway can use the TLE8250VSJXUMA1 to connect a vehicle CAN network to a higher-level controller or gateway processor. The 2 Mbps bus rate accommodates request-response diagnostics and network traffic, and the 4.5 V to 5.5 V operating supply simplifies integration with regulated 5 V electronics. The extended -40°C to +150°C range provides useful environmental margin for vehicle installations. The interface should include the termination and transient-protection approach required by the vehicle network, while PCB routing should keep the differential bus away from switching nodes and maintain a low-impedance ground reference.
추천
Industrial CAN Gateway
The TLE8250VSJXUMA1 is appropriate for an industrial CAN gateway that links factory equipment or remote sensors to an Ethernet or embedded controller. Its 2 Mbps CAN rate supports high-speed control data, while the 4.5 V to 5.5 V supply range fits regulated industrial logic. The -40°C to +150°C rating supports deployments across temperature-controlled and less controlled machinery areas. Engineers should still verify EMC margins, surge requirements, grounding, and cable length for the installation, and should use the manufacturer's recommended bus protection when the gateway connects to external field wiring.
추천
Distributed Automation Node
A distributed automation node can use the TLE8250VSJXUMA1 to communicate over a multi-drop CAN network with controllers, drives, sensors, and remote I/O. The 2 Mbps maximum rate allows the network to carry timely command and status traffic, and the 4.5 V to 5.5 V supply range is compatible with common embedded power systems. The extended operating-temperature range supports industrial environments. Reliable implementation depends on correct termination placement, matched CAN_H and CAN_L routing, suitable grounding, and protection appropriate to the cable length and electromagnetic environment.
추천
Embedded CAN Communication Module
The TLE8250VSJXUMA1 can serve as the physical-layer interface in a compact embedded CAN communication module. It provides the required CAN transceiver function between a host controller and the differential bus, with a maximum data rate of 2 Mbps and a 4.5 V to 5.5 V supply range. The compact 8-pin PG-DSO-8-16 package supports space-constrained board layouts. Keep the bus interface close to the connector, provide local supply decoupling, and follow the Infineon application schematic to maintain predictable electromagnetic performance and bus fault tolerance.
추천
Robotic Control Network
The TLE8250VSJXUMA1 is suitable for robot and machine-control networks that exchange synchronized commands and sensor data over CAN. The 2 Mbps data rate supports responsive control traffic, while the 4.5 V to 5.5 V supply integrates readily with standard embedded rails. Its -40°C to +150°C operating range can assist in equipment exposed to variable ambient temperatures. The bus layout should use symmetric differential routing and appropriate termination; motor drives and switching regulators should be spatially separated or filtered to prevent conducted and radiated noise from disturbing communications.
추천
추천 제품 요약
엔지니어링 참조 데이터: TLE8250VSJXUMA1 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Brand | Infineon Technologies |
| Package | PG-DSO-8-16, 8-SOIC |
| Device Type | CAN bus transceiver |
| Protocol | CANbus |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Maximum Data Rate | 2 Mbps |
| Operating Temperature Range | -40°C to +150°C |
| RoHS Status | Compliant |
설계 노트
Place the transceiver close to the CAN bus connector and keep the CAN_H and CAN_L traces short, symmetrical, and referenced to a continuous ground plane. Avoid routing the bus pair beneath switching power stages or across discontinuous plane boundaries. Consistent geometry reduces radiated emissions and helps the receiver reject differential noise and common-mode disturbance.
Provide the transceiver with a regulated supply inside the 4.5 V to 5.5 V operating range and place the recommended decoupling capacitor close to the supply pins. Keep supply-current return paths short and use the manufacturer's application schematic for component values. Verify startup, bus dominance, and voltage behavior across the complete system supply tolerance rather than at nominal 5 V alone.
Use the termination arrangement recommended for the network topology and add surge or transient protection when the CAN conductors leave the protected enclosure. Connect protection-device returns to the appropriate ground reference and keep those paths compact. In systems with variable-speed motors or switching supplies, evaluate common-mode filtering and physical separation between the bus connector and high-energy switching nodes.
규정 준수 정보
RoHS compliance is identified in the JLCPCB component listing. REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status were not identified and require confirmation from the manufacturer or applicable compliance documentation.
