TLV2342ID - Dual 8V 320kHz Op Amp | Texas Instruments
부품 번호: TLV2342ID ✓ 활성TLV2342ID 개요
An operational amplifier is a high-gain differential amplifier used to amplify small signals in analog and mixed-signal circuits. The TLV2342 belongs to the linear-amplifier hierarchy and the LinCMOS operational-amplifier family. Two independent amplifier sections can implement filters, buffers, sensor amplifiers, comparators, and low-level signal-conditioning stages within one package.
The principal operating characteristics are an 8 V supply limit, a 320 kHz gain-bandwidth product, and dual-channel operation in the SOIC (D) package. Its low-voltage CMOS architecture supports single-supply systems where circuit designers need an amplifier that can operate near the lower supply rail. The manufacturer identifies the TLV2342 family as intended for low-voltage, single-supply applications.
Compared with general-purpose bipolar input amplifiers, the TLV2342 emphasizes CMOS-style operation, low-voltage capability, and a compact dual implementation. The 320 kHz gain-bandwidth product makes it appropriate for audio-range, control, and instrumentation signal paths rather than high-speed data acquisition or precision measurement requiring megahertz bandwidth. Its 8-pin SOIC package also simplifies assembly where a through-hole-style small-outline footprint is preferred over a fine-pitch array package.
Typical uses include low-level sensor conditioning, active analog filters, audio preamplification, threshold detection, and signal buffering in battery-powered or compact embedded equipment. The two amplifier channels can also be configured as a comparator or as the active elements of an instrumentation circuit when the common-mode and output-swing limits suit the application.
Design should begin by verifying the signal input range, output swing, common-mode range, noise, offset, and stability requirements across the actual supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive high-impedance input routes should be kept short and away from switching nodes. The manufacturer datasheet should be used for the exact pin assignments, input and output limits, recommended operating conditions, and compensation requirements.
This page combines the TLV2342ID operating specifications with package information, drop-in alternatives, comparison parameters, and practical design guidance to accelerate component selection and PCB implementation for low-voltage analog signal chains.
드롭인 대체품: TLV2342ID — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
TLV9102ID
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TLV2372IDR
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TLV2344ID
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →TLV2342YID
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
TLV2342ID 최대 정격 & 전기적 특성
| Amplifier Type | Dual operational amplifier |
| Number of Amplifier Circuits | 2 circuits |
| Technology | CMOS LinCMOS |
| Maximum Supply Voltage | 8 V |
| Supply Configuration | Single supply |
| Gain-Bandwidth Product | 320 kHz |
| Input Type | Rail-to-rail input |
| 출력 유형 | Rail-to-rail output |
| 패키지 | 8-pin SOIC (D) |
| 실장 유형 | Surface mount |
TLV2342ID 8-pin soic (d) 핀 구성 가이드
TLV2342ID(8-pin soic (d) 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: TLV2342ID.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TLV2342ID 적합 용도: 6 애플리케이션s: Portable Sensor Signal Conditioning, Audio Preamplification, Active Analog Filters, Industrial Control Signal Buffering, Low-Voltage Threshold Detection, Battery-Powered Data Acquisition.
Portable Sensor Signal Conditioning
The TLV2342ID fits low-voltage sensor front ends that need two amplifier channels on a compact single-supply board. Its rail-to-rail input characteristic supports signal ranges that approach the supply rails, while the 320 kHz gain-bandwidth product is appropriate for common temperature, pressure, and position sensors rather than high-speed sensing. One channel can amplify the sensor output and the other can provide active filtering or level conditioning. Place the bypass capacitors close to the supply pins, use short high-impedance input routes, and verify that the sensor output remains inside the amplifier's common-mode and output-swing limits.
추천
Audio Preamplification
The TLV2342ID is suitable for stereo audio preamplification in portable and compact analog equipment because it provides two amplifier channels, supports single-supply operation, and offers a 320 kHz gain-bandwidth product. Each channel can amplify a low-level source before a power-output stage, or the two channels can implement successive stages of gain and filtering. Headroom, distortion, noise, and channel matching must be checked at the intended signal level. Stable feedback-network layout and short output routing are particularly important when using higher closed-loop gains.
추천
Active Analog Filters
The TLV2342ID can implement first- or second-order active filters in low-voltage instrumentation because its two independent channels permit separate gain and filtering stages. A 320 kHz gain-bandwidth product leaves useful bandwidth for audio-range and control signals while supporting the moderate closed-loop gains commonly used in filter sections. The rail-to-rail input characteristic helps preserve signal amplitude near the supply limits, although exact common-mode limits and output swing must be respected. Verify filter stability, resistor tolerance, capacitor selection, and the effect of amplifier noise before fixing the implementation.
추천
Industrial Control Signal Buffering
The TLV2342ID is useful for buffering and conditioning low-level control signals in compact industrial systems operating from a low-voltage supply. Two channels can isolate a sensor or controller from downstream filter and driver stages, reducing loading while maintaining compatibility with the TLV2342 family's low-voltage CMOS design. The 8-pin SOIC package supports conventional surface-mount assembly. Designers should confirm output-current capability, capacitive-load stability, noise behavior, and allowable input common-mode range for the selected rail and operating temperature.
추천
Low-Voltage Threshold Detection
The TLV2342ID can be configured as a comparator or threshold detector when its input and output ranges satisfy the monitored signal. The rail-to-rail input characteristic is valuable in compact systems where the signal may sit near a supply rail, and the dual-channel arrangement can monitor two thresholds or provide a hysteretic decision function. Comparator use still requires attention to propagation delay, input overvoltage behavior, output saturation, and noise at the switching threshold. Referencing the manufacturer's truth table and limit values is necessary before treating the amplifier as a logic element.
추천
Battery-Powered Data Acquisition
The TLV2342ID fits compact battery-powered acquisition systems that process slow or moderate-bandwidth analog inputs. A single positive supply and rail-to-rail input capability simplify signal conditioning around sensors whose output moves across much of the available rail. The 320 kHz gain-bandwidth product supports gain stages and anti-alias filtering for many low-speed measurements, while the dual package reduces board area. Validate total quiescent current, input bias current, offset, noise, and common-mode behavior across battery voltage, then place bypass and filter components close to the amplifier pins.
추천
추천 제품 요약
엔지니어링 참조 데이터: TLV2342ID — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | TLV9102ID | TLV2372IDR | TLV2344ID | TLV2342YID |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Amplifier Configuration | Dual | Dual | Dual | Dual | Dual |
| Technology | CMOS LinCMOS | CMOS | CMOS | CMOS LinCMOS | CMOS LinCMOS |
| Low-Voltage Single-Supply Design | Yes | Yes | Yes | Yes | Yes |
| Number of Pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins |
| Drop-In Status | Original device | Identified by Texas Instruments as a drop-in replacement with upgraded functionality | Pin-compatible review required | Same-family review required | Same-family temperature-grade review required |
주요 차별점
- Lower-voltage operating point for compact single-supply designs (vs TLV9102ID)
- Established TLV2342-family compatibility (vs TLV2342YID)
- Documented upgrade path (vs TLV9102ID)
설계 노트
Place the supply-bypass capacitor directly between the supply and ground pins, with the ground connection forming the shortest possible return path. For a dual amplifier, check whether each channel requires local decoupling near its feedback components. Keep the footprint compatible with the 8-pin SOIC (D) outline and confirm terminal orientation against the manufacturer pin diagram before releasing artwork.
Route the inverting input and feedback components close to the amplifier pins because parasitic resistance and capacitance can alter gain and stability. Avoid routing high-impedance input nodes beneath digital traces or near switching power stages. A solid ground plane and short analog traces help preserve low-level signal integrity, particularly when the amplifier is configured for moderate or high closed-loop gain.
Do not assume that rail-to-rail input operation guarantees full rail-to-rail output swing or that the amplifier can remain linear at every input level. Check the manufacturer limits for input common-mode range, output swing, supply range, and output-current capability. When using either channel as a comparator, also review input overvoltage behavior, propagation delay, and output logic levels.
규정 준수 정보
The TLV2342ID is an industrial dual operational amplifier rather than an automotive-qualified device, so AEC-Q100 is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not stated in the cited product information.