TLV2773CN - Dual 5.1 MHz Rail-to-Rail Op Amp | Texas Instruments
부품 번호: TLV2773CN ✓ 활성TLV2773CN 개요
An operational amplifier is an analog integrated circuit that amplifies the difference between its inverting and non-inverting inputs. A dual device contains two independent amplifiers in one package, reducing board area when a signal path needs two gain stages. The TLV2773 belongs to the amplifier hierarchy: operational amplifier, analog amplifier, analog signal-conditioning IC, and integrated circuit. Its rail-to-rail output capability is useful when the usable signal range must extend toward either supply rail.
The main performance features are the 5.1 MHz gain-bandwidth product, the 10.5 V/µs slew rate, and the shutdown function. The bandwidth permits moderate-frequency signal amplification, while the slew rate helps the outputs track larger input steps with less distortion. The shutdown control supports systems that need to reduce activity when a circuit is idle, although power-consumption figures should be taken from the manufacturer datasheet for the exact operating state.
The TLV2773 family uses a CMOS process and is specified for rail-to-rail output operation. Input common-mode range, output-voltage swing, offset voltage, input bias current, noise density, and supply-current characteristics should be confirmed in the manufacturer datasheet before precision amplifier calculations or ac-versus-dc sensitivity analysis.
Typical uses include low-voltage sensor conditioning, buffered analog measurement chains, audio preamplification, active filtering, and general-purpose dual-amplifier signal processing. The 14-PDIP package also makes the device suitable for prototypes, educational laboratories, through-hole prototypes, and industrial or instrumentation assemblies where a socketed or manually assembled dual amplifier is preferred.
Designers should verify shutdown pin polarity, input and output voltage limits, unity-gain stability, and decoupling requirements in the pin-description table and recommended operating conditions. Place the supply bypass capacitor close to the device and route sensitive input and feedback traces away from switching nodes. This page consolidates the manufacturer product information, package details, sourcing guidance, and design considerations needed for an initial engineering evaluation.
드롭인 대체품: TLV2773CN — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청TLV2773CN 최대 정격 & 전기적 특성
| Amplifier Type | Dual operational amplifier |
| 토폴로지 | Rail-to-rail output |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz |
| Slew Rate | 10.5 V/µs |
| Number of Channels | 2 channels |
| Shutdown | Yes |
| Process Technology | CMOS |
| Package Type | 14-PDIP |
| Package Body Width | 0.300 inch (7.62 mm) |
| 실장 유형 | Through-hole |
| Unity-Gain Bandwidth | 5.1 MHz |
| RoHS 상태 | RoHS3 compliant |
TLV2773CN 0.300 inch (7.62 mm) 핀 구성 가이드
TLV2773CN(0.300 inch (7.62 mm) 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: TLV2773CN.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TLV2773CN 적합 용도: 6 애플리케이션s: Low-Voltage Sensor Signal Conditioning, Stereo Audio Preamplification, Active Filtering and Equalization, Instrumentation Buffering, Data Acquisition Front End, Portable and Battery-Powered Instruments.
Low-Voltage Sensor Signal Conditioning
The TLV2773CN suits low-voltage sensor front ends requiring two amplification or buffering stages on one board. Its 5.1 MHz gain-bandwidth product provides moderate-frequency capability, and the 10.5 V/µs slew rate allows the outputs to respond to relatively fast input transitions. Each channel can amplify a resistive-bridge, resistive-divider, or transducer output referenced near the lower supply rail. Rail-to-rail output improves available swing, but the input common-mode limits must be checked before the sensor is connected. Place a local bypass capacitor at the supply pins and route the high-impedance sensor input away from switching circuitry.
Stereo Audio Preamplification
The dual TLV2773CN can provide left and right preamplifier channels for low-voltage stereo audio systems. Its 5.1 MHz gain-bandwidth product covers the audio band with substantial margin, while the 10.5 V/µs slew rate helps maintain low distortion on larger signal transitions. Rail-to-rail output increases the usable signal range from a 2.7 V to 5.5 V supply. Gain-setting resistors should be placed close to the inverting inputs, and feedback traces should remain short and shielded from digital and switching nodes. Confirm the manufacturer noise and distortion characteristics before using the device in a high-sensitivity microphone path.
Active Filtering and Equalization
The TLV2773CN can implement dual active-filter or equalization sections because it combines two amplifiers with a 5.1 MHz gain-bandwidth product. The gain-bandwidth value gives designers margin above the filter passband, while the 10.5 V/µs slew rate supports higher-amplitude waveform shaping. Verify stability at the selected closed-loop gain and keep the required passive components close to the relevant pins. Resistor tolerances and capacitor tolerances normally dominate filter accuracy, but the amplifier must also maintain acceptable phase margin at the highest frequency of interest. The shutdown feature can disable the filter during idle operating intervals.
Instrumentation Buffering
In laboratory and industrial instrumentation, the TLV2773CN can buffer two measurement inputs while operating from a 5 V or 3.3 V rail. The dual 5.1 MHz channels support moderate-bandwidth sensing without requiring separate amplifier packages. The through-hole 14-PDIP package is especially convenient for prototype instruments, educational setups, and assemblies assembled by hand. Use a low-noise reference and short guard traces for high-impedance sources, and verify input offset and bias-current limits in the manufacturer electrical characteristics before using the device for precision dc measurements. Add supply bypass capacitance at the device pins to keep reference noise from coupling into the measurement path.
Data Acquisition Front End
The TLV2773CN is useful in a compact data-acquisition front end that conditions two incoming analog channels before conversion or comparison. Its 5.1 MHz gain-bandwidth product supports higher-rate signals than a purely low-frequency precision amplifier, while the 10.5 V/µs slew rate limits large-signal slew effects. Rail-to-rail output permits the conditioned signal to occupy more of the available supply range. The shutdown input supports duty-cycled acquisition systems where the amplifier should be inactive between measurement windows. Establish the required gain, analog bandwidth, settling time, and output headroom before finalizing component values and the acquisition timing.
Portable and Battery-Powered Instruments
The TLV2773CN is appropriate for portable instruments because it operates from 2.7 V to 5.5 V and provides a shutdown control for reducing activity when measurements are not needed. The two channels can support dual sensing, gain stages, or active-filter sections while keeping the 14-PDIP footprint compact compared with two single-amplifier packages. Battery life depends on the exact supply current in the selected operating mode, which must be confirmed in the manufacturer electrical characteristics. Confirm the regulator dropout, startup behavior, load-transient response, and analog signal levels to ensure reliable operation over the battery's discharge range.
엔지니어링 참조 데이터: TLV2773CN — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Package | 14-PDIP (0.300 inch, 7.62 mm) |
| Brand | Texas Instruments |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz |
| Slew Rate | 10.5 V/µs |
| Output Topology | Rail-to-rail output |
| Shutdown Function | Yes |
| Process Technology | CMOS |
| RoHS Status | RoHS3 compliant |
주요 차별점
- Through-hole dual-amplifier implementation (vs TLV9362IDDFR)
- Lower dynamic bandwidth with integrated shutdown (vs TLV9362IDDFR)
- Dual amplifier in one 14-pin through-hole package (vs Single-channel through-hole alternatives)
설계 노트
Place the supply bypass capacitor directly across the device's positive supply and ground pins, with the ground connection following the shortest practical return path. Keep high-impedance input and inverting-feedback traces away from the capacitor connection, power inductors, and switching nodes. For the 14-PDIP implementation, observe the package notch when locating pin 1 and confirm every connection against the manufacturer pin-description table.
Rail-to-rail output does not guarantee the same rail-to-rail input range. Check the input common-mode limits, output swing, input offset voltage, and bias current before designing a signal source that operates close to either supply rail. Also confirm the shutdown pin polarity and logic threshold from the datasheet so the control signal does not place the amplifier in an unintended state during power sequencing.
Use short, well-grounded feedback loops and avoid routing the non-inverting input next to the output. A single ground or via connection is often preferable to a long chain of vias through multiple ground planes. When driving a capacitive load, evaluate stability with the manufacturer's recommended isolation resistor. These steps help prevent oscillation, improve settling, and preserve the expected 5.1 MHz bandwidth and 10.5 V/µs slew-rate performance.
규정 준수 정보
A product listing identifies the TLV2773CN as RoHS3 compliant and associates the series with automotive sourcing. A listing association alone does not establish AEC-Q100 qualification for this ordering code.