TS3704CD - Quad Micropower CMOS Comparator | STMicroelectronics
부품 번호: TS3704CD ✗ 단종TS3704CD 개요
A voltage comparator is an analog integrated circuit that compares an input voltage with a reference voltage and changes its digital output state when the relationship between the two signals changes. The TS3704CD belongs to the comparator hierarchy: analog mixed-signal IC, voltage comparator, quad comparator, and power-management signal-conditioning IC. Four independent channels in one package can reduce board area and simplify designs requiring several threshold-detection or overvoltage-monitoring functions.
The TS3704CD uses CMOS circuitry to limit consumption and a push-pull output stage to eliminate the external pull-up resistor normally required with open-collector comparators. The four channels share a common supply arrangement within the package, while each comparator provides its own non-inverting and inverting inputs and logic output. This makes the device applicable to threshold crossings, sensor interfaces, signal conditioning, and general-purpose digital logic interfaces.
According to the manufacturer datasheet, the TS3704 is a micropower quad CMOS voltage comparator whose typical current is approximately 9 uA per comparator, while the identified TLC3704 comparison records state 35 uA. Push-pull outputs can drive CMOS-compatible loads directly and transition without the passive pull-up network associated with open-drain comparators. Designers should still check output current, supply voltage, input common-mode range, and output levels for each operating condition before reuse.
Typical uses include battery-powered monitoring, industrial control thresholds, sensor signal conditioning, window comparison, and four-channel level detection. The 14-SO package is suitable for conventional through-hole assembly and prototype boards. Because TS3704CD is obsolete, engineers should use a qualified drop-in option when possible or confirm lifecycle, availability, and qualification requirements for long-term production programs.
For a new PCB, preserve the 14-pin SOIC footprint and verify every signal against the replacement part's pin description. Pay particular attention to input common-mode range, propagation delay, output polarity, supply voltage, and input bias current, since a matching package alone does not guarantee equivalent behavior in every operating condition.
This page consolidates lifecycle information, verified distributor records, pin-compatible migration options, comparison parameters, and practical replacement guidance. The structured alternatives help engineers move away from the obsolete TS3704CD without relying on a mechanically similar but electrically unsuitable part.
드롭인 대체품: TS3704CD — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
TLC3704CDR
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TS3704IDT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TS3V3704IDT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MAX964EPA
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
TS3704CD 최대 정격 & 전기적 특성
| Comparator Type | General-purpose voltage comparator |
| Number of Channels | 4 channels |
| Logic Family | CMOS |
| Output Style | Push-pull |
| 공급 전압 | 3 V nominal |
| Typical Current per Comparator | 9 uA |
| Comparator Current in Matched TLC3704 Family | 35 uA typical |
| 동작 온도 범위 | 0°C to 70°C |
| 패키지 | 14-SO, 0.154 in (3.90 mm) width |
| 실장 유형 | Surface mount |
| 수명 주기 상태 | Obsolete |
| Maximum Power Dissipation | 830 mW |
TS3704CD 14-so, 0.154 in (3.90 mm) width 핀 구성 가이드
TS3704CD(14-so, 0.154 in (3.90 mm) width 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: TS3704CD.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TS3704CD 적합 용도: 6 애플리케이션s: Battery-Powered Threshold Detection, Industrial Sensor Signal Conditioning, Overvoltage and Undervoltage Protection, Window Comparator for Signal Limits, Smart Sensor Interface Logic, Digital Logic Level Conditioning.
Battery-Powered Threshold Detection
The TS3704CD fits battery-powered threshold detection because its four CMOS comparator channels consume about 9 uA per comparator according to the manufacturer datasheet. Each channel can compare a sensed voltage against an external reference and produce a push-pull logic result without a continuously active pull-up resistor. This reduces both component count and standby loading in portable monitoring equipment. For a new design, an active TS3V3704IDT or another verified 14-SO option should be evaluated because the original TS3704CD is obsolete. Verify battery operating voltage, comparator common-mode range, and the output leakage required by the connected microcontroller.
추천
Industrial Sensor Signal Conditioning
The TS3704CD can convert sensor-derived analog voltages into CMOS-compatible threshold decisions for industrial monitoring. Its four channels allow multiple inputs, such as temperature, pressure, or level signals, to be compared against separate references while sharing one 14-SO footprint. The approximately 9 uA typical current per comparator supports low-power sensing nodes, and the push-pull output avoids a static pull-up load. When replacing the obsolete device with TS3704IDT or TS3V3704IDT, check the industrial temperature grade, input common-mode limits, propagation delay, and the complete supply range before production.
추천
Overvoltage and Undervoltage Protection
Four independent TS3704CD channels can supervise several voltage rails and generate logic flags when an input crosses a programmed threshold. Placing two comparators around a reference can create window monitoring, while individual channels can detect overvoltage or undervoltage on separate supplies. The 3 V nominal device class and low typical consumption suit compact protection subsystems, although actual rail compatibility must be confirmed from the electrical limits. For new designs, use TS3704IDT or TS3V3704IDT when the extended temperature rating is appropriate and confirm input range, output polarity, and startup behavior.
추천
Window Comparator for Signal Limits
The TS3704CD is suitable for implementing upper and lower signal limits with two channels, leaving two channels available for a second monitored signal. A reference divider establishes the threshold, while the comparator output identifies whether the measured voltage lies inside or outside the permitted window. Its push-pull output can connect directly to CMOS-compatible control logic, avoiding the external pull-up required by open-collector devices. A replacement must preserve the same pin assignment and timing behavior; review the TLC3704CDR, TS3704IDT, and MAX964EPA data for common-mode range, propagation delay, and output levels before substitution.
추천
Smart Sensor Interface Logic
The TS3704CD can perform the first decision stage in a smart-sensor interface by comparing a conditioned analog measurement with a reference before digital conversion or transmission. Four channels permit multiplexing several sensor outputs through one package, reducing PCB footprint in compact IoT and appliance designs. Its CMOS implementation and approximately 9 uA typical consumption per comparator align with low-energy sensing nodes. When replacing it, verify offset voltage, input bias current, common-mode range, and propagation delay, since these specifications determine thresholds near sensor idle levels and the timing of a subsequent digital sample.
추천
Digital Logic Level Conditioning
A TS3704CD channel can translate a slowly changing or noisy analog condition into a push-pull digital level suitable for downstream CMOS logic. Two complementary comparisons can also generate an above-limit, below-limit, or in-range indication. The push-pull stage avoids the passive pull-up network used with open-collector comparators and supports compact, low-power logic blocks. For replacement qualification, check output high and low levels against the receiving device, confirm the 3 V-class supply compatibility, and test threshold accuracy across temperature. TS3704IDT is appropriate when an industrial-temperature alternative is required.
추천
추천 제품 요약
엔지니어링 참조 데이터: TS3704CD — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | TLC3704CDR | TS3704IDT | TS3V3704IDT | MAX964EPA |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | Texas Instruments | STMicroelectronics | STMicroelectronics | Analog Devices |
| Package | SOIC-14 | SOIC-14 - same | SOIC-14 - same | SOIC-14 - same | SOIC-14 - same |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
주요 차별점
- Lower stated consumption in the original TS3704 family (vs TLC3704CDR)
- Same-manufacturer migration retains familiar device architecture (vs TS3V3704IDT)
- Documented terminal and package compatibility (vs TLC3704CDR)
- Cross-brand sourcing path in the same 14-pin footprint (vs MAX964EPA)
설계 노트
Do not treat a matching 14-SO footprint as proof of electrical compatibility. Build a substitution matrix that compares every input, output, supply, and ground connection, then verify supply limits, input common-mode range, offset voltage, output levels, propagation delay, and temperature grade. Pay particular attention to the TLC3704CDR, whose stated typical comparator current is 35 uA compared with approximately 9 uA per comparator for the TS3704 family. Prototype threshold behavior and startup timing before releasing a replacement to production.
Calculate comparator consumption across all four channels rather than relying on one channel's typical current. For the TS3704 family, the manufacturer datasheet lists approximately 9 uA per comparator, while the TLC3704CDR record lists 35 uA typical. A four-channel system therefore requires separate power-budget calculations for the original and replacement. Include reference-divider current, pull-up leakage, and downstream CMOS input current because those loads can dominate total standby consumption.
Keep each comparator's reference network and protected input close to its associated pins to reduce susceptibility to switching noise and ground bounce. Route the shared supply and ground paths to minimize loop area, place required bypass capacitance near the device, and keep the unused comparator inputs tied to a defined valid level rather than left floating. After substitution, inspect each new pin name against the PCB netlist because equivalent functions may occupy different pins on different manufacturers' quad comparators.
Verify output rise and fall behavior at the actual receiving logic's supply voltage and input capacitance. A push-pull output removes the external pull-up used with open-collector comparators, but transition timing can still matter when driving long PCB traces, cables, or a backplane. Test around the decision threshold with realistic noise and reference drift, and confirm that propagation delay and output-level specifications preserve the system's required response time.
규정 준수 정보
The obsolete TS3704CD product records do not provide a complete current compliance declaration for RoHS, REACH, AEC-Q100, lead-free status, halogen-free status, or conflict minerals.