XC6SLX4-L1CSG225C - Spartan-6 LX FPGA, 132 I/O | AMD
부품 번호: XC6SLX4-L1CSG225C ✓ 활성XC6SLX4-L1CSG225C 개요
An FPGA is a semiconductor whose digital logic, interconnect, and dedicated I/O resources are configured after manufacture. FPGA architecture sits between fixed-function logic ICs and programmable ASIC development: designers can implement parallel processing, control logic, interface bridging, and protocol handling in hardware. The Spartan-6 LX family targets cost-sensitive embedded systems that require more flexibility than a microcontroller or discrete logic can provide.
The XC6SLX4-L1CSG225C combines 132 I/O with a 221,184-logic-cell Spartan-6 LX device. Its 3,840 flip-flops support stateful sequential logic, while the 225-CSPBGA package supports dense board routing without a fine-pitch leaded package. The L1 speed and power grade favors designs where energy efficiency is important, including embedded control, instrumentation, communications, and industrial equipment.
FPGA performance depends on the implemented architecture, clocking, memory resources, I/O standards, and routing rather than on a single headline figure. The large I/O count allows the device to connect external data buses, status signals, clocks, and control interfaces concurrently. Designers must also account for configuration storage, startup behavior, clock jitter tolerance, I/O voltage compatibility, power budgeting, and heat dissipation in the 225-CSPBGA package.
Typical uses include industrial data-acquisition systems, embedded test equipment, protocol converters, low-cost signal-processing platforms, and control modules that combine multiple bus interfaces. The device can also serve as the central programmable element in camera, medical-instrument, communications, and robotics products where parallel hardware processing improves throughput or reduces external component count.
A new board should follow AMD Spartan-6 power, configuration, clocking, and package-design guidance. In particular, preserve clean power and ground distribution, route configuration signals for deterministic startup, validate every I/O voltage domain, and examine junction-temperature and power-signal-integrity margins before releasing the layout.
This product overview combines the XC6SLX4-L1CSG225C device identity, package information, I/O count, logic resources, and drop-in alternatives with practical guidance for FPGA selection, schematic design, PCB implementation, sourcing, and lifecycle verification.
드롭인 대체품: XC6SLX4-L1CSG225C — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: XC6SLX4-L1CSG225C (동일 폼 팩터 및 풋프린트) — 차이점: Device Type, Package, Logic Cells, Temperature Grade, User I/O.
XC6SLX4-2CSG225C
✅ 드롭인가격 문의
데이터시트 보기 →XC6SLX4-L1CSG225I
✅ 드롭인가격 문의
데이터시트 보기 →XC6SLX4-2CSG225I
✅ 드롭인가격 문의
데이터시트 보기 →XC6SLX4-1CSG225C
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
XC6SLX4-1CSG225I
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
XC6SLX4-L1CSG225C 최대 정격 & 전기적 특성
| Device Type | Spartan-6 LX FPGA |
| Manufacturer | AMD / Xilinx |
| Logic Cells | 221184 cells |
| Flip-Flops | 3840 flip-flops |
| User I/O | 132 I/O |
| Total Terminals | 225 terminals |
| 패키지 | 225-CSPBGA (CSG225) |
| Package Code | LFBGA |
| Package Shape | Square |
| Terminal Form | Ball |
| 실장 유형 | Surface mount |
| Performance Grade | L1 |
| Device Family | Spartan-6 LX |
| Programmable Logic Type | Field-programmable gate array |
XC6SLX4-L1CSG225C square 핀 구성 가이드
XC6SLX4-L1CSG225C(square 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: XC6SLX4-L1CSG225C.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
XC6SLX4-L1CSG225C 적합 용도: 6 애플리케이션s: Industrial Data Acquisition, Industrial Protocol Converter, Programmable Logic Controller, Embedded Signal Processing, Communications Gateway, Test and Measurement Instrument.
Industrial Data Acquisition
The XC6SLX4-L1CSG225C fits parallel data-acquisition systems that must combine sensor conditioning, digital filtering, buffering, and control logic. Its 221,184 logic cells and 3,840 flip-flops provide substantial configurable logic for channel multiplexing, timing control, and status sequencing, while 132 user I/O can accommodate parallel sensor inputs, trigger signals, and communications. The L1 performance option is appropriate when lower-power operation is preferred over maximum performance. Implement acquisition channels as modular logic blocks and verify acquisition timing against the selected clocking scheme, since the number of usable user pins can be affected by dedicated power, ground, clock, and configuration assignments in the 225-CSPBGA package.
Industrial Protocol Converter
The Spartan-6 LX XC6SLX4-L1CSG225C can bridge legacy parallel buses with serial interfaces by translating state machines, FIFO-like data paths, and protocol engines in programmable logic. Its 132 user I/O is useful for multiple chip-select, interrupt, byte-enable, and clock signals, while 221,184 logic cells allow several protocol engines to operate concurrently. Place serial transceivers or level translators close to the relevant BGA balls and keep long external routes away from sensitive clock and configuration nets. Before release, verify protocol timing, signal polarity, supported I/O voltage standards, and the maximum operating rate of the implemented interfaces against the device operating conditions.
Programmable Logic Controller
The XC6SLX4-L1CSG225C is suitable for a compact programmable logic controller that coordinates sensors, actuators, interlocks, counters, timers, and communication tasks. The 3,840 flip-flops support state-machine and sequencing logic, while the larger 221,184-cell device allows parallel datapaths to coexist with control functions. The 225-CSPBGA package helps reduce board area, but its fine-pitch ball grid demands careful escape routing and assembly planning. For dependable operation, define fail-safe states, reset behavior, and watchdog handling in the hardware architecture, and validate all actuator outputs during power-up, reset, configuration, and fault conditions rather than relying only on firmware sequencing.
Embedded Signal Processing
For embedded filtering, correlation, waveform generation, or fixed-point processing, the XC6SLX4-L1CSG225C provides programmable parallel logic that can execute multiple samples per clock cycle. Its 221,184 logic cells and 3,840 flip-flops allow arithmetic pipelines to be balanced across several processing elements, while 132 I/O supports parallel data inputs, coefficient loading, and result capture. The L1 grade is attractive when the design prioritizes energy efficiency rather than maximum switching performance. Use synchronous clocking, pipeline registers, and deterministic I/O timing, and confirm that the target's available block RAM, DSP resources, and clock-management requirements are sufficient before committing to the architecture.
Communications Gateway
The XC6SLX4-L1CSG225C can serve as the programmable control and data-plane element of a communications gateway that handles packet routing, framing, buffering, and host-interface logic. Its 132 user I/O provides capacity for parallel buses and control signals, and its programmable architecture permits protocol updates without changing the PCB. The CSG225 package supports compact integration but requires a disciplined power-distribution network because switching activity can create dynamic supply noise. Keep configuration access reliable, validate every high-speed interface against its voltage and timing requirements, and test bit-error performance across voltage, temperature, and clock-frequency corners before production release.
Test and Measurement Instrument
The XC6SLX4-L1CSG225C is suitable for programmable test and measurement front ends that sequence stimuli, acquire responses, and perform timing or pattern analysis. The device can implement counters, timing generators, digital pattern logic, and parallel acquisition paths in one programmable device, reducing the number of discrete components. With 221,184 logic cells and 132 user I/O, multiple instrument channels can be consolidated while retaining flexible control interfaces. The design should include deterministic startup and self-test logic, isolate analog sections from digital switching noise, and validate the programmed clock, I/O standards, and acquisition windows against the instrument's required measurement accuracy.
엔지니어링 참조 데이터: XC6SLX4-L1CSG225C — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | XC6SLX4-2CSG225C | XC6SLX4-L1CSG225I | XC6SLX4-2CSG225I | XC6SLX4-1CSG225C | XC6SLX4-1CSG225I |
|---|---|---|---|---|---|---|
| Brand | AMD / Xilinx | AMD / Xilinx | AMD / Xilinx | AMD / Xilinx | AMD / Xilinx | AMD / Xilinx |
| Package | 225-CSPBGA (CSG225) | 225-CSPBGA (CSG225) - same | 225-CSPBGA (CSG225) - same | 225-CSPBGA (CSG225) - same | 225-CSPBGA (CSG225) - same | 225-CSPBGA (CSG225) - same |
| Device Family | Spartan-6 LX | Spartan-6 LX | Spartan-6 LX | Spartan-6 LX | Spartan-6 LX | Spartan-6 LX |
| Performance Option | L1 | 2 | L1 | 2 | 1 | 1 |
| Temperature Grade Suffix | C | C | I | I | C | I |
주요 차별점
- Directly preserves the target's L1 performance option (vs XC6SLX4-2CSG225C)
- Commercial C suffix retained for lower-temperature commercial designs (vs XC6SLX4-L1CSG225I)
- Provides 132 user I/O in a compact 225-CSPBGA footprint (vs XC6SLX4-2CSG225C)
설계 노트
Use the AMD CSG225 package drawing and land pattern rather than deriving a footprint from the generic 225-ball designation. Escape each signal according to its assigned bank voltage, route configuration pins to their required pull-up or programming network, and keep sensitive clock inputs away from high-current switching outputs. The fine-pitch BGA also requires planning for via-in-pad or fanout construction, solder-paste control, and assembly inspection.
Create the power tree from the AMD device power and configuration guidance, including the required core and I/O supply sequencing. Decoupling should be placed directly at the associated supply and ground balls, with the package ground connectivity considered as part of the return path. Estimate dynamic and static power for the actual switching activity rather than relying only on device-family averages, then verify that each rail remains within its operating range across voltage, temperature, and load.
Confirm the package pinout and I/O banking before assigning external interfaces because configuration, clock, power, and ground balls can reduce the practical number of user signals. For high-speed interfaces, use controlled-length routing where required, provide clean reference planes, and match external driver and receiver characteristics to the selected voltage standard. Re-run timing analysis with the actual pin locations, clock source, and board-level loading rather than relying only on device-level timing reports.
Do not approve a substitution solely because it uses a 225-CSPBGA package. Check the exact XC6SLX4 base device, CSG225 pinout, performance suffix, temperature suffix, configuration compatibility, supported I/O standards, and timing closure. When moving from an L1 ordering code to a 1 or 2 option, recalculate clock constraints and power margins. When moving to an I suffix, verify that the intended operating range and qualification requirements are satisfied.
규정 준수 정보
The product identity, Spartan-6 LX architecture, CSG225 package, and commercial C suffix are documented. Specific environmental and material compliance declarations were not established for this ordering code.
