Produk (46,000+)

SN75114N - Dual Differential Line Driver, 5 V | Texas Instruments
SN75114N

SN75114N - Dual Differential Line Driver, 5 V | Texas Instruments

Texas Instruments SN75114N is a dual differential line driver designed for 5 V systems, with a 16-pin PDIP package and output current rated up to 40 mA. The device generates differential outputs for balanced lines such as twisted-pair interconnects while maintaining TTL-compatible output levels. Its two driver channels provide separate sink outputs and corresponding active pull-up terminals for flexible output configurations. A differential line driver is an interface IC that converts logic-level signals into complementary differential outputs suitable for balanced interconnects. This device belongs to the line-driver hierarchy within interface ICs, where it can drive twisted-pair circuits more effectively than an ordinary single-ended logic output. It also supports applications beyond conventional differential transmission, including TTL expanders and phase splitters. The SN75114N offers two differential driver channels, 5 V operation, TTL-compatible outputs, and a maximum output current of 40 mA per the manufacturer documentation. Sink outputs labeled YS and ZS operate alongside active pull-up terminals labeled YP and ZP on adjacent package pins. This arrangement allows the output stage to be configured according to the signaling requirements and loading of the balanced line. The output architecture resembles a TTL totem-pole output, but the separation of sink and active pull-up terminals provides additional routing flexibility. These terminals can be used independently when the interface requires different drive arrangements. Designers should account for output rise and fall times, propagation delay, and the allowable loading when driving long cables or slow logic inputs. Typical uses include balanced digital data links, differential clock distribution, TTL bus expansion, and phase-splitting circuits. The device is particularly useful when a system needs stronger source current than standard logic gates can provide while retaining TTL-compatible signal levels. Keeping the differential return path close to the signal conductors helps reduce susceptibility to common-mode noise. For PCB implementation, place the device close to the driven line and route each differential conductor as a compact pair. Avoid long stubs, maintain a continuous ground reference, and terminate the line according to its impedance and topology. Verify output current, cable length, logic thresholds, and timing margins under the intended temperature and supply conditions. This product page combines the manufacturer's core electrical and functional information with package-level design guidance, replacement analysis, application examples, and engineering-focused comparison criteria. These supporting sections help engineers distinguish exact family alternatives from broader RS-422, RS-485, and differential-interface devices that may use different packages or logic levels.

RFC Hubungi kami
SN75116D - 5V Differential Line Transceiver | Texas Instruments
SN75116D

SN75116D - 5V Differential Line Transceiver | Texas Instruments

Texas Instruments SN75116D is a 1/1 differential line transceiver with a single 4.5 V to 5.5 V supply, TTL-compatible driver inputs and receiver outputs, and a 16-pin SOIC (D) package. It combines a 3-state differential driver and a differential receiver for bidirectional communication over party-line or data-bus networks. A differential line transceiver is an interface IC that converts between single-ended digital logic signals and differential signals carried by a balanced line. This signal conversion helps equipment communicate more reliably over cables or buses while remaining compatible with TTL-based systems. The SN75116D belongs to the interface IC hierarchy, where transceivers connect digital logic to physical communication lines. The principal features include a 4.5 V to 5.5 V operating supply range, TTL-compatible driver inputs, TTL-compatible receiver outputs, 3-state driver output circuitry, and differential line operation. Its single transceiver arrangement integrates one driver channel and one receiver channel in each 16-pin SOIC package, making it appropriate for compact point-to-point, bus-organized, and party-line interfaces. The SN75116D is designed for party-line and data-bus applications where multiple nodes may share a communication line. The 3-state driver output allows the driver to be disconnected electrically when it is not active, supporting shared-bus architectures. TTL-compatible logic levels simplify interfacing with conventional digital systems, while differential line operation improves signal integrity across the physical transmission path. Typical uses include industrial data acquisition, instrumentation, test equipment, embedded control links, and industrial communication networks. The device is particularly relevant when a system requires bidirectional differential signaling but only one driver and one receiver channel. Its SOIC package also supports conventional surface-mount assembly rather than requiring a through-hole connection. Designers should use the manufacturer datasheet pin-description table when assigning signals and should account for the 4.5 V to 5.5 V supply requirement. The 3-state output must be controlled correctly on a shared bus, and the external line network should be configured to prevent multiple drivers from actively driving the same node at the same time. This page organizes the SN75116D technical characteristics, sourcing information, verified drop-in alternative, interface applications, comparison parameters, and practical PCB design guidance. It helps engineers evaluate the transceiver against same-footprint replacements while keeping electrical compatibility and bus topology central to the selection.

RFC Hubungi kami
SN75116N - Differential Line Transceiver | Texas Instruments
SN75116N

SN75116N - Differential Line Transceiver | Texas Instruments

Texas Instruments SN75116N is a single differential line transceiver containing one 3-state driver and one receiver, operates from a single 5 V supply, and is packaged in a 16-pin PDIP. The device interfaces TTL-type digital systems with differential data-transmission lines and is intended primarily for party-line or data-bus arrangements where multiple nodes can share a bus. Its specified operating-temperature range is 0 to 70 °C. A differential line transceiver is an interface IC that converts between single-ended TTL logic and a differential line signal. This signal hierarchy belongs to the broader sequence of transceiver, interface IC, semiconductor, and electronic communication systems. Differential signaling helps reject common-mode noise because the receiver evaluates the voltage difference between two conductors rather than one conductor referenced only to ground. The SN75116N therefore fits between a bus controller or terminal logic and a physical differential bus. Key features include a single 5 V supply, TTL-compatible driver inputs, TTL-compatible receiver outputs, and a 3-state driver output that allows a connected node to release the bus when inactive. The integrated driver and receiver reduce the number of external interface components needed in a party-line topology. The 16-pin PDIP package also supports conventional through-hole assembly and prototyping workflows. Driver and receiver timing, propagation delay, and bus loading remain important system-level considerations when this device is added to an existing bus. The SN75116N is intended for TTL-to-differential line conversion in party-line data buses. Its 3-state driver supports shared-bus arrangements, while the differential receiver improves noise immunity over a direct single-ended connection. Designers should account for propagation delay, bus termination, cable length, node stub effects, and the voltage margins required by the connected TTL devices. Because the device combines one driver and one receiver, system partitioning may require additional transceivers to balance each node's transmit and receive paths. Typical uses include industrial control buses, instrumentation interfaces, point-to-point differential links, and legacy TTL equipment connected to balanced cabling. The device is also appropriate for laboratory prototypes and repair systems that need a straightforward 16-pin through-hole interface. In every case, the selected cables, connectors, grounding method, and logic family must preserve the voltage thresholds and signal timing expected by the bus. A key implementation consideration is the receiver control function associated with this transceiver family. Confirm the exact control-pin behavior and timing from the manufacturer datasheet before substituting a related family member. When the PCB footprint must remain unchanged, the SN75116N should be treated as a design-specific component rather than replaced solely because another differential transceiver has similar headline features. This page combines the manufacturer's product identity, exact ordering package, commercial sourcing path, functional comparisons, and practical interface-design guidance. It also identifies where timing, pin-level, compliance, and alternative-device details require direct verification before schematic release or PCB reuse.

RFC Hubungi kami
SN751177NSR - Dual RS-422/RS-485 Transceiver, 10Mbps, 16-SO | TI
SN751177NSR

SN751177NSR - Dual RS-422/RS-485 Transceiver, 10Mbps, 16-SO | TI

The Texas Instruments SN751177NSR is a dual differential driver and receiver pair in a 16-pin Small-Outline (SOIC, NS package) form factor, designed for full-duplex RS-422 and RS-485 balanced multipoint bus transmission at data rates up to 10 Mbits/s. It integrates two drivers and two receivers in a monolithic BiCMOS IC, with positive- and negative-output current limiting on the driver stages for robust bus-fault handling in noisy industrial environments. A transceiver IC is an interface device that converts single-ended logic signals (TTL/CMOS) into the differential voltage levels required by standards such as RS-422 and RS-485, while also converting incoming differential signals back to single-ended logic for a UART, MCU, or ASIC. The RS-485 family in particular enables robust multipoint communication over long twisted-pair cables by using differential signaling with high common-mode rejection, supporting up to 32 nodes on a single bus segment. The SN751177 meets ANSI TIA/EIA-422-B and TIA/EIA-485-A standards as well as ITU-T V.10 and V.11 recommendations, making it suitable for interbuilding and industrial backbone links. Key specifications include 10 Mbits/s signaling rate, a wide 4.75V to 5.25V supply range, 50 mV typical receiver hysteresis for noise immunity, and thermal shutdown with current limiting on the driver outputs. The driver slew-rate design enables reliable 10 Mbps operation without excessive EMI. This part is implemented in TI's bipolar/CMOS mixed process, allowing low power consumption (typical supply current around 50 mA) combined with high drive strength (differential output >2V across 50 ohm loads). The 16-pin SOIC (NS) package provides a compact footprint suitable for point-to-point cables, multidrop backplanes, and isolated data links when paired with digital isolators. An enable pin arrangement supports half-duplex direction control on the SN751178 variant; the SN751177 offers a fixed direction split suitable for full-duplex point-to-point links. Typical applications include factory-floor PLC networking, building-automation RS-485 trunks, point-of-sale (POS) terminals, motor-control encoder feedback links, and industrial sensor aggregation nodes. Its 50 mV receiver hysteresis makes it tolerant of slow edge rates from long cables and opto-isolated interfaces. When designing with the SN751177NSR, ensure proper bus termination (typically 120 ohms across the differential pair at each cable end) and use a fail-safe biasing network to prevent false receiver output during idle bus states. A 100 nF decoupling capacitor placed within 5 mm of the VCC pin is essential for stable high-speed operation. This page synthesizes distributor stock, parametric drop-in alternatives, and practical RS-485 design notes not typically consolidated in the manufacturer datasheet, helping engineers quickly evaluate fit, supply, and second-source options.

RFC Hubungi kami
SN75117D - 5V Differential Line Transceiver | Texas Instruments
SN75117D

SN75117D - 5V Differential Line Transceiver | Texas Instruments

The Texas Instruments SN75117D is a 5 V differential line transceiver in an 8-pin SOIC package, combining a differential driver, a differential receiver, and three-state driver output circuitry in one device. It operates from a single 5 V supply, accepts a maximum supply voltage of 5.5 V, and provides a maximum transmit delay of 30 ns with a maximum receive delay of 75 ns. A differential line transceiver is an interface IC that transmits and receives data across a balanced connection. The transmitter converts a single-ended logic signal into a differential pair, while the receiver detects the voltage difference between the two conductors. Differential signaling rejects common-mode noise, reduces electromagnetic interference, and supports dependable communication over cables or board-level twisted-pair interconnects. The SN75117D features TTL-compatible driver inputs and a TTL-compatible receiver output. Its driver output can be placed in a three-state condition, allowing the driver to be disabled when shared bus direction control is required. The receiver supports differential line operation and includes receiver-output strobe control as a family-level feature of the SN75117 device. The device is intended for balanced data links where low propagation delay, noise immunity, and bus direction control are important. Its 30 ns maximum transmit delay is suitable for moderate-speed control and instrumentation links, while the 75 ns maximum receive delay provides a defined upper limit for receiver-side timing. The single 5 V supply also simplifies interfacing with TTL and other 5 V digital systems. Typical uses include industrial equipment links, instrumentation buses, data acquisition systems, telecommunications equipment, and computer peripherals. In these systems, the SN75117D can place a balanced signal onto a cable, recover the signal at the far end, and provide a logic-compatible receiver output to downstream digital circuitry. PCB design should preserve the differential signal path, use a controlled ground reference, and place termination and protection components close to the line interface. The receiver and driver timing should be checked against the connected cable length and system clock requirements. Power decoupling should follow the manufacturer datasheet layout to minimize supply disturbance during output transitions. This product page combines the manufacturer's device features with practical interface-circuit guidance, timing considerations, package information, sourcing instructions, and design guidance for engineers evaluating the SN75117D in a differential communications design.

RFC Hubungi kami
SN75118N - 5V Differential Line Transceiver | Texas Instruments
SN75118N

SN75118N - 5V Differential Line Transceiver | Texas Instruments

The Texas Instruments SN75118N is a 5 V differential line transceiver that combines a 3-state differential line driver and a differential-input line receiver in a 16-pin PDIP package. It interfaces TTL-type digital systems with balanced data-transmission lines and supports party-line or data-bus arrangements where multiple nodes share one differential pair. Its single 5 V supply, TTL-compatible driver inputs, TTL-compatible receiver output, and separate receiver enable control make it suitable for legacy industrial, communications, instrumentation, and data-acquisition equipment. The SN75118N uses an enable input on the receiver rather than the receiver strobe arrangement used by the related SN75117, allowing the receiving path to be disabled independently of the driver output. The transceiver is designed to place a TTL or CMOS-style logic signal onto a differential line and recover a logic-level output from the differential signal arriving on the same bus. Differential signaling rejects common-mode noise and improves noise immunity when the two line conductors receive equal interference. The driver's 3-state output can be released for party-line operation, preventing a disabled node from blocking the shared bus while another node transmits. The SN75118N family is intended for point-to-point and multipoint data-bus interfaces rather than modern high-rate LAN or automotive Ethernet links. Its differential driver, receiver, and control architecture allow a controller to manage transmit and receive paths within one device. Because it is a legacy bipolar-era interface IC, the design must account for the electrical limits and operating conditions stated in the manufacturer datasheet rather than assuming compatibility with contemporary RS-485 or RS-422 transceivers. The SN75118 is identified by Texas Instruments as a differential line transceiver. The N ordering code denotes the 16-pin PDIP package, measuring 19.3 mm by 9.4 mm with a stated body area of 181.42 mm². The device operates from a single 5 V supply and provides a driver input that accepts TTL-compatible logic levels, a receiver output that drives TTL-compatible logic levels, and a three-state driver output suitable for shared-bus designs. Typical uses include industrial data acquisition, telemetry interfaces, test and measurement equipment, multipoint control buses, and legacy communications equipment. The SN75118N is most appropriate where a 5 V TTL system must connect to a differential line and where transmitter disable and receiver enable functions are required. It is also suitable for systems that need a shared bus rather than a dedicated point-to-point link. When laying out a circuit around the SN75118N, route the differential pair together, keep the driver output in a high-impedance state whenever the node is not transmitting, and follow the receiver-enable polarity shown in the manufacturer pin description table. Confirm the bias and termination arrangement for the specific line length and data rate, because the device is a general-purpose differential transceiver rather than a network PHY with integrated cable compensation. This page organizes the SN75118N specifications, verified sourcing references, and design considerations into a single engineering reference. It also distinguishes the N-package ordering option from related family members whose receiver-control arrangements and package formats differ, helping engineers determine whether a substitute is genuinely pin-to-pin compatible before committing to a PCB change.

RFC Hubungi kami
SN75119D - Differential Line Transceiver | Texas Instruments
SN75119D

SN75119D - Differential Line Transceiver | Texas Instruments

The Texas Instruments SN75119D is a single-channel differential line transceiver with a single 5 V supply, three-state driver outputs, TTL-compatible driver inputs, and a TTL-compatible receiver output. It is packaged in an 8-pin SOIC and is designed for party-line, data-bus, and balanced differential-line communication systems. The SN75119D uses an enable input rather than the receiver output strobe arrangement used by related SN75116 and SN75117 devices. A differential line transceiver is an interface IC that combines a transmitter and receiver for communication over a balanced pair of conductors. It belongs to the broader transceiver and interface-controller hierarchy, where differential signaling improves noise immunity by rejecting common-mode voltage disturbances. The SN75119D supports this function by combining differential line operation with a three-state driver output that can be disabled when multiple devices share a bus. Key features include operation from a single 5 V supply, three-state driver output circuitry, TTL-compatible driver inputs, and a TTL-compatible receiver output. The enable function allows the receiver to participate in shared-bus communication systems where bus contention must be controlled. These characteristics make the device suitable for legacy industrial data buses, point-to-point balanced links, and systems that require controlled driver states rather than always-active outputs. The architecture supports both transmitting and receiving on a differential line. The driver accepts TTL-level control signals and places complementary signals onto the bus, while the receiver reconstructs a logic output from the differential pair. Three-state operation provides a high-impedance state when the driver is disabled, allowing multiple transmitters to share the same pair of wires under controlled address or arbitration schemes. The related SN75118 family member uses an enable arrangement as well, while SN75116 and SN75117 devices provide receiver output strobe control. Typical applications include party-line industrial control buses, data acquisition networks, peripheral-interface equipment, test systems, and legacy communications equipment. The part is also appropriate where a controller must switch a differential transmitter on and off while several nodes remain connected to the same bus. System designers should coordinate enable timing to avoid unwanted driver overlap and preserve signal integrity. For PCB implementation, place the transceiver close to the connector or bus transceiver to minimize exposed stub length and reduce susceptibility to reflected signals. Follow the manufacturer's pin-description table and recommended decoupling arrangement when assigning tracks. The single 5 V rail should be filtered locally, and unused digital inputs should be held at defined logic levels rather than left floating. This page organizes the confirmed operating characteristics, package information, sourcing paths, functional-use guidance, and design considerations into a practical engineering reference. It also distinguishes the SN75119 enable architecture from the receiver-strobe behavior of related family members and highlights the design decisions that matter when deploying the SN75119D on a shared differential bus.

RFC Hubungi kami
SN75119P - 5V Differential Line Transceiver | Texas Instruments
SN75119P

SN75119P - 5V Differential Line Transceiver | Texas Instruments

The Texas Instruments SN75119P is a differential line transceiver integrated circuit designed for bidirectional TTL data transmission over a single differential line. It operates from a single 5 V supply and combines a 3-state differential line driver with a differential-input line receiver. The device is packaged as an 8-pin PDIP and is intended for party-line, data-bus, and point-to-point differential communication systems. Its driver output can be placed in a high-impedance state, allowing multiple nodes to share one bus while disabled. A differential line transceiver is an interface IC that bridges conventional TTL-compatible digital logic and a balanced data line. The transmitter converts a TTL input into a differential output, while the receiver converts differential line voltage into a TTL-compatible output. This two-wire differential arrangement helps reject common-mode noise, supports longer interconnects than single-ended logic in appropriate systems, and allows bidirectional communication when driver and receiver controls are managed correctly. The SN75119 family provides 3-state driver output circuitry, TTL-compatible driver inputs, TTL-compatible receiver output, and differential line operation. The receiver includes an enable control for placing its output in a high-impedance state. The SN75119 uses the SN75119 family arrangement in which the receiver output strobe and driver enable functions are combined for party-line operation. These features make the device useful where several bus nodes need controlled connection and disconnection. Typical applications include industrial data buses, instrumentation interfaces, computer peripheral links, point-to-point balanced links, and multi-drop communication networks. Designers should pay attention to the enable timing, termination strategy, cable length, node count, and logic levels when connecting the device to a differential line. The 8-pin PDIP package is suitable through-hole assembly and is particularly useful for legacy equipment, repair, and prototype systems where a small surface-mount package would be inconvenient. For new designs, verify the complete electrical limits and recommended operating conditions in the manufacturer datasheet before applying the transceiver to a specific bus. A proper system design uses compatible line termination, controlled tri-state timing, and a defined idle state. The SN75119P remains useful when maintaining or expanding equipment that already uses the SN75119 family interface. This page combines the device’s core operating characteristics, practical bus-design guidance, application context, and available replacement information to support faster component evaluation and sourcing decisions.

RFC Hubungi kami
SN75121N - Dual 2/0 Line Driver, 16-PDIP | Texas Instruments
SN75121N

SN75121N - Dual 2/0 Line Driver, 16-PDIP | Texas Instruments

The Texas Instruments SN75121N is a dual 2/0 line driver IC designed for digital data transmission over lines with impedances from 50 to 500 ohms. The device is compatible with standard TTL logic and supply-voltage levels and is packaged in a 16-pin through-hole DIP. Each of its two channels provides a low-impedance emitter-follower output capable of driving terminated coaxial-cable or twisted-pair lines. A line driver is an interface IC that converts a digital logic signal into a stronger output suitable for transmission through a cable, bus, or other wired connection. In the electronic-component hierarchy, the SN75121N belongs to the line-driver family within interface ICs and broader digital communication and signal-conditioning systems. Its purpose is to restore signal amplitude and loading capability after a source device has driven a line through an electrically demanding interconnect. The SN75121N provides two independent driver channels in a 2/0 organization, meaning two outputs and no corresponding input-driver designation in the product description. Its emitter-follower output topology provides low output impedance, while the uncommitted outputs support wired-OR logic. These characteristics make the device useful where multiple signal sources must share a transmission line under properly controlled pull-up or pull-down arrangements. The low-impedance outputs are intended for terminated lines such as coaxial cable and twisted pair. When calculating transmission-line performance, account for the 50-to-500-ohm line range identified by Texas Instruments. Logic compatibility simplifies connection with conventional TTL systems, while the 16-pin DIP format supports through-hole construction and prototype boards where a surface-mount package is unnecessary. Typical applications include industrial control links, point-to-point digital communication, instrument interfaces, legacy computer peripherals, and factory equipment that uses balanced or unbalanced terminated connections. The device can also support bus arrangements where wired-OR behavior is intentional. Application-specific timing, cable length, termination, and noise-margin requirements still need to be validated in the complete system. The primary design consideration is the output-stage implementation. Because the outputs are uncommitted and use emitter-follower behavior, the board designer must provide the correct biasing, termination, pull-up or pull-down arrangement, and signal-return path. Do not assume that a line will remain valid solely because the driver can source current; verify voltage levels, edge rate, bus contention, cable capacitance, and receiver thresholds in the finished design. This page organizes the Texas Instruments SN75121N around its verified line-driver function, package, interface characteristics, replacement choices, comparison parameters, and practical implementation concerns. It is intended to help engineers identify the correct package variant, distinguish genuine pin-compatible alternatives from merely similar drivers, and plan the surrounding termination and signal-integrity circuitry before committing a design to production.

RFC Hubungi kami
SN75123D - Dual TTL Line Driver | Texas Instruments
SN75123D

SN75123D - Dual TTL Line Driver | Texas Instruments

Texas Instruments SN75123D is a dual line-driver interface IC designed for IBM System 360 input/output interfaces and compatible with standard TTL logic. The device operates from a single 5 V supply, provides a 3.11 V output at -59.3 mA, and reaches a maximum transmit delay of 25 ns. It is packaged in a 16-pin SOIC. A line driver is a digital interface IC that converts logic-level inputs into stronger output signals capable of driving terminated cables, coaxial links, or twisted-pair lines. The dual SN75123 belongs to the line-driver and receiver class of interface ICs. Its primary role is to improve signal integrity and drive capability across long or shared bus wiring rather than to perform data conversion or voltage regulation. The SN75123D operates from one 5 V supply and is compatible with standard-TTL logic levels. Its emitter-follower outputs are designed for low-impedance line driving and support party-line operation, where multiple drivers can share a bus when their outputs are appropriately controlled. The output structure also provides short-circuit protection, a useful characteristic when a connected line is faulted or incorrectly terminated. The 3.11 V output level at -59.3 mA indicates strong high-level output drive capability. With a maximum transmit delay of 25 ns, the device supports communication systems that require faster edge propagation than general-purpose logic buffers. The manufacturer identifies the SN75123 family as meeting or exceeding the IBM System 360 input/output interface requirements while remaining compatible with standard-TTL supply and logic levels. Typical uses include terminated coaxial cable links, twisted-pair communication channels, computer peripheral interfaces, industrial data links, and legacy equipment built around TTL or IBM System 360 interfaces. Because the outputs use an uncommitted emitter-follower structure, designers can implement party-line networks in which connected drivers share the same physical conductor. For a new design, verify the receiver's threshold requirements, line termination, cable length, and grounding arrangement before assigning the driver. The 16-pin SOIC package simplifies assembly and rework, but the output enable, input, ground, and supply pins must be connected according to the manufacturer datasheet. A single 5 V rail and common ground reference are fundamental to reliable operation. This product page combines the manufacturer's functional description with engineering-focused comparison, application, and design guidance. It also clearly distinguishes directly substitutable components from candidates that require different packages or interfaces, helping engineers preserve PCB compatibility when planning replacements or design reuse.

RFC Hubungi kami
SN75124N - Triple Line Receiver | Texas Instruments
SN75124N

SN75124N - Triple Line Receiver | Texas Instruments

Texas Instruments SN75124N is a triple differential line receiver designed for IBM System 360 input/output interfaces and compatible with standard TTL logic. It operates from a single 5 V supply, provides three receiver channels in a 16-pin PDIP package, and includes built-in input-threshold hysteresis for improved noise immunity. A line receiver is an interface IC that restores valid logic levels from signals degraded by distance, capacitance, crosstalk, or transmission-line reflections. Within the interface hierarchy, the SN75124N belongs to the receiver family of TTL-compatible logic and bus-interface components, where it sits between a noisy physical communication link and digital processing logic. Differential reception is especially useful when a system must distinguish a valid transition from common-mode noise. The principal benefits of the SN75124N are its three-channel architecture, single 5 V operation, TTL compatibility, and integrated input hysteresis. Combining three receivers in one 16-pin PDIP reduces component count and board area in equipment requiring several independent communication channels. The hysteresis helps a receiver ignore small voltage disturbances near its switching threshold, improving dependable operation in systems with noisy interconnects. According to the Texas Instruments datasheet, the SN75124 was specifically designed to meet the input/output interface specifications for IBM System 360. It is also compatible with standard TTL logic and supply voltage levels. These details position the device as a legacy-compatible interface solution rather than a modern multi-gigabit transceiver, making it most appropriate for established TTL or IBM System 360 equipment. Typical applications include IBM-compatible computer peripherals, industrial control interfaces, legacy storage equipment, telecommunications equipment, and embedded systems that receive differential signals with TTL-level outputs. It can also be evaluated in instrumentation or test systems where a short cable or backplane connection introduces noise but remains within the receiver's supported signal and supply conditions. The primary design consideration is verifying that the connected signal amplitude, common-mode range, bus loading, and system thresholds satisfy the SN75124N requirements. Designers should also account for TTL input and output levels, supply decoupling, unused receiver channels, and any protection needed for externally accessible connectors. The 16-pin PDIP format favors through-hole assembly and repairability rather than compact surface-mount production. This page combines the manufacturer interface description, package information, application guidance, verified-equivalent checks, and practical selection considerations. It also distinguishes a genuine pin-to-pin replacement from a merely similar line receiver, helping engineers avoid substitutions that change channel count, pin assignment, logic polarity, or electrical requirements.

RFC Hubungi kami
SN75127N - Seven-Channel 5V Line Receiver | Texas Instruments
SN75127N

SN75127N - Seven-Channel 5V Line Receiver | Texas Instruments

The Texas Instruments SN75127N is a seven-channel line receiver designed for single 5 V operation, with a 20 kΩ input resistance and outputs compatible with TTL Schottky-clamped transistors. The device belongs to the interface-IC hierarchy and is intended for receiving digital signals in equipment built around the IBM 360/370 I/O specification. Its seven independent receiver channels consolidate repetitive point-to-point logic interfaces into one integrated circuit. A line receiver is an interface IC that converts a digital signal arriving through a cable, bus, or wired connection into a clean logic-level output suitable for the next digital circuit. Within the broader semiconductor hierarchy, the SN75127N is a receiver within the interface IC family, where it sits between external wiring and TTL-compatible logic. This makes it useful in legacy computer, peripheral, industrial-control, and communication equipment where a multi-channel receiver offers a simpler implementation than seven discrete receiver circuits. The primary features are seven receiver channels, operation from one 5 V supply, 20 kΩ input resistance, and compatibility with TTL Schottky-clamped output stages. The IBM 360/370 I/O compatibility cited in the manufacturer documentation indicates that the device was designed for a defined class of high-speed digital interfaces. Its multi-channel organization also reduces package count and simplifies board-level routing when several related lines must be received. The SN75127N is a bipolar logic interface device whose receiver channels convert incoming digital voltage levels into standard logic signals. Although the available manufacturer-linked material identifies the device as a high-speed receiver, complete timing, propagation-delay, supply-current, and logic-threshold values must be taken from the manufacturer datasheet before final timing-budget and worst-case analysis. Engineers should also account for the effects of cable length, source termination, grounding, and system noise when applying the receiver at the end of a wired interface. Typical applications include IBM 360/370-compatible peripheral interfaces, TTL-compatible computer equipment, multi-bit data buses, industrial control systems, test equipment, and communications equipment requiring several received logic channels. The seven-channel architecture is particularly useful where parallel data or control lines arrive together and need buffering before reaching TTL logic. A single package can therefore replace repetitive single-channel receiver circuitry where the system already uses compatible voltage levels. When designing a board around the SN75127N, verify every package pin, logic threshold, enable condition, and propagation delay against the manufacturer datasheet. Keep input and ground-return paths short where practical, maintain compatible logic levels throughout the interface, and avoid treating the receiver as a modern differential line transceiver. These checks are especially important when replacing an older device because footprint compatibility alone does not establish timing or threshold equivalence. This product page combines the verified device identity, operating characteristics, and application context with practical guidance for replacement, layout, sourcing, and interface design. It also distinguishes documented functions from parameters that require a final datasheet review, helping engineers make a technically defensible decision when maintaining or redesigning a seven-channel TTL-compatible interface.

RFC Hubungi kami
SN75128N - 8-Channel TTL Line Receiver | Texas Instruments
SN75128N

SN75128N - 8-Channel TTL Line Receiver | Texas Instruments

Texas Instruments SN75128N is an eight-channel line receiver for TTL-compatible digital interfaces, operating from a single 5 V supply in a 20-pin PDIP package. The receiver provides eight channels, a 53 mA supply current, a 30 ns receive delay, and an input resistance of 20 kΩ. Its output interface is compatible with TTL Schottky-clamped transistors, making it suited to legacy parallel-bus and computer-interface systems that require multiple digital return paths on one package. An eight-channel line receiver is an interface IC that receives digital signals and restores them to valid logic levels for the following logic stage. In the product hierarchy, a line receiver belongs to the interface-IC family, which sits between external signal wiring and digital logic or processing electronics. Unlike a single-ended transceiver, the SN75128N is identified specifically as a receiver, making it relevant where a system needs reliable detection of eight incoming logic signals but does not require a matching driver in the same package. The SN75128N meets or exceeds the requirements stated for the IBM System 360/370 input/output specification. Its eight-channel organization reduces component count in wide parallel data paths, while the 30 ns receive delay supports communication systems operating at data rates where that propagation interval remains relevant. The single 5 V supply and 53 mA supply current simplify legacy power planning compared with a multi-rail interface design. Its 20 kΩ input resistance is designed to work with TTL-compatible source circuits, and its outputs are compatible with TTL Schottky-clamped transistor loads. These characteristics make it most applicable to older computer peripheral interfaces, bus-control equipment, instrumentation, and industrial control systems that retain discrete parallel logic rather than modern serial field buses. The device belongs to the interface IC category, not the amplifier, logic, or microprocessor categories. Typical applications include legacy peripheral bus receivers, parallel status and control links, digital test equipment, industrial control interfaces, and embedded systems communicating with older TTL-compatible logic. Eight independent receive channels are useful when a board needs to bring multiple lines from a cable, backplane, or logic connector into a digital controller while maintaining a common 5 V supply architecture. The main design consideration is interface compatibility. Confirm that the source voltage levels, cable termination, system timing, and required output rise and fall times agree with the SN75128 family characteristics before placing the device in a new design. Keep interconnect routing short and use an appropriate ground-return path, particularly when long cables or slow edges can allow reflections and noise coupling to distort the received signal. This product page combines the identified device specifications, package information, lifecycle-related sourcing considerations, interface applications, and engineering guidance into a focused engineering reference. It also distinguishes verified drop-in substitutions from general cross-reference tools, helping designers avoid assuming that a similar line receiver is automatically pin-compatible.

RFC Hubungi kami
SN75138D - Quad Bus Transceiver | Texas Instruments
SN75138D

SN75138D - Quad Bus Transceiver | Texas Instruments

Texas Instruments SN75138D is a quadruple differential bus transceiver with four independent bidirectional channels, a 4.75 V to 5.25 V supply range, and a 16-pin SOIC (D) package. Each channel combines a TTL-compatible driver, a high-input-impedance receiver, and a common driver-strobe control. The open-collector driver outputs are designed to sink loads up to 100 mA and include clamp diodes for transient protection. A bus transceiver is an interface IC that connects digital logic to a bidirectional data bus. The SN75138D belongs to the RS-485-style interface hierarchy: its drivers place data onto a single-ended transmission line, while its receivers recover logic-level signals from the same conductors. This arrangement allows one device to support two-way communication while keeping the bus driver inactive when the transceiver is receiving. The four channels provide independent TTL-compatible driver inputs, receiver outputs, and bus-side driver/receiver connections. A common driver strobe gives the host logic control over whether the open-collector outputs are enabled. High-input-impedance receivers reduce loading on the bus, while the specified 4.75 V to 5.25 V operating range supports conventional 5 V digital systems. The driver outputs support loads up to 100 mA, making the interface suitable for systems requiring wired bus drive rather than only low-power logic interconnection. Operationally, the SN75138D separates the logic-side signal path from the bus-side signal path. Driver inputs accept TTL levels and control the corresponding open-collector outputs. Receiver inputs monitor the bus and present TTL-compatible signals at the receiver outputs. Clamp diodes help limit excessive voltage excursions on driver outputs, while the high-impedance receiver structure supports shared-bus communication. The common driver strobe provides a single point for coordinating driver state across the four channels. Typical applications include industrial control buses, instrumentation links, computer peripheral interfaces, multipoint data communication, and embedded systems that require several bidirectional bus connections. The device can also be used where several TTL systems must exchange data over a shared wired network without continuously driving the bus. For reliable implementation, place the device close to the line-driver and receiver circuitry, route the bus away from sensitive clock and analog signals, and provide the supply bypassing recommended in the manufacturer documentation. Confirm termination, fail-safe biasing, and cable length against the required bus topology. The strobe signal must be sequenced so that only one node drives the shared bus at a time. This product page summarizes the SN75138D architecture, verified operating characteristics, package details, lifecycle status, replacement considerations, and practical integration guidance. It also distinguishes verified device functions from parameters that require confirmation against the manufacturer datasheet before a new design is released.

RFC Hubungi kami
SN75138N - Quad Bus Transceiver | Texas Instruments
SN75138N

SN75138N - Quad Bus Transceiver | Texas Instruments

Texas Instruments SN75138N is a quadruple bus transceiver with four independent bidirectional channels, a single 5 V supply, and a 16-pin PDIP package. Each channel combines a TTL-compatible driver with a TTL-compatible receiver for two-way communication over single-ended transmission lines. Driver outputs use open-collector architecture and support loads up to 100 mA, while receiver inputs feature high impedance and a high switching threshold. A bus transceiver is an interface IC that connects digital logic to a shared or point-to-point transmission line. Its driver stage translates TTL logic into an appropriate line-level output, while its receiver stage converts the returned signal into a logic-compatible output. In the SN75138N, the receiver input is internally connected to the corresponding driver output, allowing each channel to support two-way bus communication. The SN75138N includes common driver-strobe TTL-compatible inputs and clamp diodes on its driver outputs. The common strobe inputs provide a coordinated way to control all four open-collector drivers, which is useful when multiple devices must enter or leave a bus state together. The 100 mA open-collector output capability also permits the drivers to sink substantial bus current while supporting wired-AND behavior on a shared bus. Each of the four channels is electrically identical, which simplifies system design when several devices communicate through the same package. The high-input-impedance receivers reduce loading on the transmission line, while the high-threshold receivers help distinguish active bus states from noise or inactive line conditions. The open-collector outputs require an external pull-up resistor when used with a wired bus. Typical applications include bidirectional single-ended data links, computer peripheral interfaces, industrial control buses, test equipment, and embedded systems that require several independently controlled transceiver channels. The combination of four channels, TTL-compatible logic, and open-collector bus outputs is particularly useful when a design needs bidirectional data flow without assigning a separate transceiver IC to each signal. When laying out the PCB, place the device close to the connector or transmission-line interface and route driver and receiver paths to minimize stub lengths and crosstalk. Provide a suitable pull-up resistor on each wired-AND bus, and check the total sink current from all connected drivers. The 16-pin PDIP package also requires adequate spacing around the leads for through-hole insertion and soldering. This page consolidates the SN75138N function, verified technical characteristics, package information, design guidance, and replacement considerations. It supports faster component selection by separating verified device facts from practical PCB, bus, and sourcing guidance engineers can apply during design-in.

RFC Hubungi kami
SN75140P Dual Line Receiver, 5V | Texas Instruments
SN75140P

SN75140P Dual Line Receiver, 5V | Texas Instruments

Texas Instruments SN75140P is a dual single-ended line receiver with TTL-compatible outputs and strobes, operating from a single 5 V supply in an 8-pin PDIP package. It provides two receiver channels, a common externally adjustable reference voltage, a common strobe, and input sensitivity of ±100 mV. The device is designed for party-line and data-bus systems where low input current and adjustable switching thresholds are important. A dual line receiver is an interface integrated circuit that converts small differential or single-ended signals received over a cable or bus into logic-level outputs. In the broader semiconductor hierarchy, it belongs to interface ICs and performs the receiver function within a communications link. A line receiver complements a line driver: the driver places a signal onto the transmission line, while the receiver restores that signal to a valid logic level for the connected digital system. The SN75140P supports a common reference voltage adjustable from 1.5 V to 3.5 V, allowing the switching threshold to be optimized for noise immunity in a particular system. Its ±100 mV input sensitivity enables recognition of small signals, while the low input current of less than 100 uA suits shared party-line arrangements. The two channels share one reference-voltage pin and one strobe input, reducing control overhead in a dual-channel bus interface. TTL-compatible outputs and strobes allow the receiver to operate with conventional TTL logic. The device can also be used as a single-ended line receiver, a gated oscillator, or a level comparator. These functions make the same hardware applicable to data acquisition, bus monitoring, communications equipment, and systems in which a variable threshold is preferable to a fixed internal reference. Typical applications include multipoint data buses, industrial control interfaces, peripheral data links, instrumentation interfaces, and legacy computer equipment. When the SN75140P is used with a compatible line driver such as the SN75453B, both devices can operate from one 5 V supply and occupy approximately the space of one 16-pin package. The SN75140P is characterized for operation from 0°C to 70°C. The most important design consideration is threshold selection. Set the common reference voltage according to the signal amplitude, noise environment, and logic thresholds of the receiving system. Because the receiver uses a shared reference input, both channels normally use the same switching threshold. Account for propagation delay and ensure that the selected threshold preserves valid data timing across the complete bus operating range. This page combines the manufacturer's device description with practical interface guidance, application context, pin-package information, and an explicit review of drop-in replacement availability. It distinguishes documented electrical capabilities from specifications that must be confirmed in the manufacturer datasheet, helping engineers make sourcing and circuit-design decisions without obscuring unresolved technical details.

RFC Hubungi kami
SN75150P - Dual RS-232 Line Driver | Texas Instruments
SN75150P

SN75150P - Dual RS-232 Line Driver | Texas Instruments

The Texas Instruments SN75150P is a monolithic dual RS-232 line driver designed for data-terminal equipment and data-communication equipment interfaces. It supports data rates up to 20 kbit/s with a full 2500 pF load, accepts TTL-compatible logic inputs, and operates from dual 12 V and -12 V power supplies. The device is packaged in an 8-pin PDIP (P) package and is characterized for operation from 0°C to 70°C. An RS-232 line driver is a signal-conditioning interface integrated circuit that converts low-voltage logic-level inputs into bipolar voltage levels suitable for RS-232 communications. Within the broader hierarchy of interface ICs, a line driver sits between digital logic and a communications transceiver. It increases voltage swing and drive capability so that a logic signal can reliably cross an RS-232 cable or short data-transmission line. The SN75150 provides two independent driver channels, allowing one package to service bidirectional or multiport serial interfaces. Its characterized 20 kbit/s rate under a 2500 pF load supports legacy RS-232 equipment, control ports, instrumentation links, and industrial data communication. The dual 12 V and -12 V supply arrangement produces the positive and negative voltage swing required by TIA/EIA-232-F, while the short-circuit withstand capability helps protect the output stage during abnormal line conditions. The logic inputs are compatible with most TTL families, making the SN75150P suitable for systems that use TTL-compatible microcontrollers, microprocessors, UARTs, or other digital controllers. Its monolithic construction gives both channels consistent operating characteristics within one package. The device is also useful as a level translator, as a driver for relatively short single-ended lines, and as a MOS-device driver where the required interface voltage and current behavior match the device ratings. Typical applications include legacy RS-232 ports, data-terminal and data-communication equipment, short-distance serial links, industrial control interfaces, and equipment that requires a pair of bipolar RS-232 outputs. Designers should pair the two channels with the appropriate receiver when full bidirectional communication is needed. The SN75150 is a driver rather than a combined transceiver, so input and output signal direction must be assigned separately. When laying out a design, place the device close enough to the line-driver interface to minimize exposure of logic-level input traces to noise, and route the RS-232 outputs directly toward the protected connector or cable interface. Confirm that the external supply rails provide the required positive and negative voltages and that the total channel loading remains within the characterized load and data-rate conditions. Maintain suitable common-mode grounding between communicating equipment. This product page combines the manufacturer interface description with practical RS-232 design guidance, verified package information, function-specific application examples, and a cautious drop-in comparison. It helps engineers identify whether the SN75150P matches the required channel count, data rate, supply arrangement, package, and environmental range before committing a board design to this legacy-compatible interface device.

RFC Hubungi kami
SN75154D - Quad RS-232 Receiver | Texas Instruments
SN75154D

SN75154D - Quad RS-232 Receiver | Texas Instruments

Texas Instruments SN75154D is a monolithic quadruple differential RS-232 line receiver with four independent receiver channels, a nominal 5 V supply, operation from 0°C to 70°C, and a 16-pin SOIC package. The device implements the receiver side of the EIA/TIA-232-E interface and is intended for data-terminal and data-communication equipment connections. A differential line receiver is an interface IC that converts a pair of bipolar data-line voltages into a logic-level output. In the broader hierarchy, a line receiver belongs to an interface IC, a communications transceiver, and ultimately a semiconductor. The SN75154D is designed for relatively short, single-line, point-to-point interfaces where noise immunity, adjustable input thresholds, and fail-safe behavior are more important than the bidirectional functions provided by a full RS-232 transceiver. The SN75154D provides four receiver channels, a 7 kΩ input resistance, adjustable input thresholds for fail-safe operation, and compatibility with the EIA/TIA-232-E voltage range. Its maximum data rate is 1 Mbit/s, making it suitable for conventional RS-232 links and other point-to-point signaling paths. The 5 V to 5.5 V supply range also supports integration with common 5 V digital systems. The monolithic Schottky implementation combines four receivers in one package while maintaining the voltage thresholds expected by RS-232 equipment. Each differential input accepts an external signal pair and generates a corresponding logic output. Adjustable thresholds allow a system to bias the receiver toward a known state when the line is undriven, supporting fail-safe interface behavior without relying solely on external components. Typical uses include industrial serial links, point-to-point data equipment, peripheral interfaces, embedded control systems, and legacy RS-232 test equipment. The device can also work with a separate line driver in systems that require transmission and reception but do not need a single combined transceiver package. For reliable implementation, maintain the voltage limits and input-threshold conditions specified by the manufacturer datasheet, place bypass capacitance close to the supply pins, and route differential inputs to minimize differential pickup. Because the SN75154D provides receivers only, a suitable line driver is required wherever the same equipment must transmit over the RS-232 interface. This page combines package, interface, application, and design guidance with drop-in comparison information. It also identifies the key electrical parameters that should be checked before replacing an existing quadruple differential line receiver, helping engineers evaluate footprint compatibility, signal logic, supply voltage, temperature range, and fail-safe threshold behavior together.

RFC Hubungi kami
SN75154N - Quad Differential RS-232 Line Receiver | Texas Instruments
SN75154N

SN75154N - Quad Differential RS-232 Line Receiver | Texas Instruments

The Texas Instruments SN75154N is a quadruple differential line receiver in a 16-pin PDIP package. It is designed for RS-232 interfaces based on ANSI Standard EIA/TIA-232-E and ITU Recommendation V.28, while also supporting relatively short, single-line, point-to-point data transmission and general level-translation applications. The device is intended for operation from a single 5 V supply and uses a low-power Schottky line-receiver implementation. A differential line receiver converts the voltage difference between a pair of signal conductors into a digital logic level. This differential signaling helps reject common-mode voltage present on the cable or circuit board. The SN75154 family is intended for data-terminal equipment and data-communication equipment interfaces where multiple RS-232 channels are needed. Its four receiver channels make it suitable for compact multiport interface assemblies, industrial control links, and legacy peripheral equipment. According to the manufacturer product information, the SN75154 has an input resistance of 7 kΩ over the full EIA/TIA-232-E voltage range. Its input threshold is adjustable to meet fail-safe requirements without external components. These features are important in RS-232 systems where an open, short, or inactive driver can place the receiver input into a valid, predictable logic state. The adjustable threshold can therefore help establish system behavior before a connected transmitter becomes active. The SN75154N uses Schottky input logic and provides four differential receiver channels in one monolithic device. It is suited to point-to-point links, interface isolation, receive-side logic interfacing, and systems that need more than one RS-232 input but do not require the corresponding transmit drivers. The four independent channels also allow a single package to handle several communication ports while reducing component count and board area compared with four single-receiver packages. Designers should provide a stable 5 V supply, place input and ground connections to minimize loop area, and account for the logic thresholds and common-mode voltage limits of the connected RS-232 network. Decoupling capacitors should be positioned close to the supply pins, and unused receiver inputs should be handled according to the manufacturer's pin-description and application guidance so that they remain in a defined state. A pull-up or pull-down arrangement may be needed where the interface must maintain a fail-safe state during startup or cable disconnection. This product page combines the manufacturer description, interface standards, package information, sourcing guidance, and practical implementation considerations. It also distinguishes the SN75154N from related orderable suffixes and identifies the limits of drop-in replacement decisions: electrical equivalence alone is insufficient unless the package, pin arrangement, supply requirements, and receiver thresholds also match the original design.

RFC Hubungi kami
SN75155D - RS-232 Line Driver/Receiver | Texas Instruments
SN75155D

SN75155D - RS-232 Line Driver/Receiver | Texas Instruments

The Texas Instruments SN75155D is a monolithic full RS-232 line driver and receiver rated for a 15 V supply, packaged in an 8-pin SOIC (D). It meets or exceeds ANSI EIA/TIA-232-E and ITU Recommendation V.28 interface requirements, provides a 10 mA current-limited transmitter output, and operates across a 0 °C to 70 °C temperature range. These characteristics make it suitable for conventional data-terminal and data-communication equipment. An RS-232 line transceiver is an interface IC that converts logic-level signals into voltage levels suitable for serial links while receiving and conditioning remote signals into logic-compatible levels. In the broader semiconductor hierarchy, it belongs to the interface IC class and combines a line driver, a line receiver, and supporting bias or regulation functions within one monolithic package. The response-control input allows a resistor or resistor-and-bias network to be connected to ground for additional receiver noise control. The SN75155D uses current-limited outputs to support RS-232 signaling without the uncontrolled drive current associated with an ideal voltage source. Its integrated low-power design is specified at 130 mW, making it useful in compact equipment where both interface performance and power consumption matter. The device combines one driver and one receiver rather than providing a complete multi-channel RS-232 port. Texas Instruments describes the SN75155 as a monolithic line driver and receiver for the interface between data terminal equipment and data communication equipment. The 8-pin SOIC package supports conventional surface-mount assembly, while the 0 °C to 70 °C range targets commercial-temperature equipment. Exact timing, supply-current, receiver-threshold, and output-level details should be taken from the manufacturer datasheet revision identified by Texas Instruments as Revision C. Typical uses include RS-232 ports for industrial control equipment, data acquisition systems, point-of-sale terminals, legacy serial adapters, and embedded systems that still communicate with RS-232 peripherals. The interface can support host-to-peripheral links where logic levels remain compatible with the SN75155 receiver and where cable length and baud rate satisfy the applicable RS-232 system design limits. When designing the circuit, treat the response-control input as a receiver-tuning element and follow the manufacturer’s resistor or resistor-and-bias connection guidance. Confirm the system ground strategy, add the required interface protection for exposed connectors, and validate signal levels at the far end of the cable rather than relying only on logic-side measurements. This product page combines the device interface role, verified package and commercial-temperature information, manufacturer documentation links, practical RS-232 design guidance, and carefully qualified same-family replacement information. It also distinguishes true electrical alternatives from ordinary reel, tape, or grade-code variants so procurement decisions remain tied to board-level compatibility.

RFC Hubungi kami
SN75155P - RS-232 Line Driver and Receiver | Texas Instruments
SN75155P

SN75155P - RS-232 Line Driver and Receiver | Texas Instruments

The Texas Instruments SN75155P is a monolithic full-duplex RS-232 line driver and receiver packaged in an 8-pin PDIP (P) package. It supports the ANSI EIA/TIA-232-E interface between data terminal equipment and data communication equipment and operates across a 0°C to 70°C commercial temperature range. The device combines one driver, one receiver, and a response control input in a single package. An RS-232 interface transceiver is a semiconductor device that converts logic-level signals into RS-232-compatible voltage levels and converts received RS-232 levels back into logic signals. In the interface hierarchy, the SN75155P belongs to the line-driver-and-receiver family, within transceivers, interface ICs, and integrated circuits. It is commonly placed between a host controller or UART and a DB-25 or equivalent RS-232 connector. The key features of the SN75155P are its integrated driver and receiver, full RS-232 operation, response control for receiver-noise adjustment, and an 8-pin PDIP package. The response control input accepts a resistor, or a resistor and bias voltage, connected to ground to control receiver noise behavior. This makes the part useful in legacy data-communication equipment where one receiver serves a console, modem, or data-terminal connection. Internally, the driver converts TTL/CMOS-level inputs into bipolar RS-232 signal levels, while the receiver converts a differential-looking RS-232 input into a logic-level output for the system controller. Because the driver and receiver operate in opposite directions, one SN75155P supports bidirectional communication when the driver output and receiver input are connected to separate interface signals. The manufacturer datasheet is the controlling reference for voltage thresholds, timing, and input-current limits. Typical applications include serial console links, data-terminal equipment, legacy printer interfaces, industrial control panels, and RS-232 test equipment. The SN75155P is also appropriate where a controller requires a receive path with adjustable noise control rather than a modern multi-channel RS-232 transceiver. When laying out an RS-232 design, place the transceiver close to the connector and keep the driver and receiver return paths routed away from sensitive analog inputs. Confirm the interface voltage thresholds, driver slew behavior, and response-control network against the manufacturer datasheet before releasing a production board. This page consolidates the manufacturer product information, package and temperature data, interface standard, application context, and substitution guidance for engineers evaluating the SN75155P in legacy serial-interface designs.

RFC Hubungi kami
SN75157D - Dual Differential Line Receiver | Texas Instruments
SN75157D

SN75157D - Dual Differential Line Receiver | Texas Instruments

The Texas Instruments SN75157D is a dual differential line receiver in an 8-pin SOIC package. It receives two differential or single-ended signals and converts each into a TTL-compatible logic output. The device operates from a single 5 V supply, with a documented operating range of 4.75 V to 5.25 V, and supports signaling rates up to 10 Mbit/s. Its inputs are compatible with EIA/TIA-422-B, EIA/TIA-423-B, ITU V.10, and ITU V.11 line-driver outputs. A differential line receiver converts a small voltage difference between two conductors into a logic-level signal while rejecting common-mode noise. In the signal path, the line receiver sits between a remote transmitter and a digital controller, logic gate array, or data-processing system. The SN75157D can accept either a differential input or a single-ended input at each receiver channel, making it useful in industrial control, instrumentation, data acquisition, and legacy communication equipment. The SN75157D uses Schottky circuitry and provides TTL-compatible outputs. According to the manufacturer datasheet, the device is supplied in 8-pin dual-in-line and small-outline versions, with the SN75157D identifying the SOIC-8 package. Its stated operating temperature range is 0 °C to 70 °C, positioning it as a commercial-temperature interface device. The maximum signaling rate is listed as 10 Mbit/s, supporting moderate-speed point-to-point and multidrop data links. The device includes two independent receiver channels, one 5 V power connection, a ground connection, and six signal pins. Differential inputs reduce susceptibility to externally induced noise because the receiver responds primarily to the voltage between the input pair rather than to their shared voltage relative to ground. Published comparison information lists fault protection from -10 V to 15 V for the SN75157D, although the input protection behavior and application limits should be verified against the complete manufacturer datasheet before applying fault voltages to a design. Typical uses include industrial RS-422 and RS-423 links, data acquisition interfaces, telemetry receivers, and test equipment. Because both receiver channels are independent, one SN75157D can recover two signals and reduce component count compared with two single-channel receivers. The logic outputs can connect directly to TTL or CMOS-compatible receiving logic after checking input thresholds and timing requirements. The primary design consideration is signal integrity. Route the differential pair as a closely matched pair, terminate the line according to the selected network topology, and keep the receiver away from high-current switching paths. Do not substitute the SN75157D for a line driver or RS-232 transceiver; the receiver's TTL outputs and differential input architecture support only the corresponding receiver application.

RFC Hubungi kami
SN75158D - Dual RS-422 Line Driver | Texas Instruments
SN75158D

SN75158D - Dual RS-422 Line Driver | Texas Instruments

Texas Instruments SN75158D is a dual differential line driver designed for ANSI EIA/TIA-422-B and ITU V.11 balanced-line interfaces, with two transmitters in an 8-pin SOIC package. It operates from a nominal 5 V supply, supports signaling rates up to 10 Mbit/s, and is specified over 0°C to 70°C. Its TTL totem-pole outputs provide high-current drive capability for balanced twisted-pair lines while maintaining a high-impedance output state when disabled. A differential line driver is an interface IC that converts two single-ended logic signals into complementary differential outputs. In the broader hierarchy, it belongs to line drivers, interface transceivers, and data-communication semiconductors. Differential signaling transmits the same information on two conductors, allowing receiver circuitry to reject common-mode noise and improve reliability over longer cable runs compared with single-ended links. Each SN75158D transmitter provides high-current source and sink capability suitable for balanced lines at normal line impedance without excessive power dissipation. The device includes a common enable function, enabling the outputs to enter a high-impedance state when the interface is inactive. Its 8-pin SOIC package supports conventional surface-mount assembly and is a practical choice for legacy industrial, telecommunications, instrumentation, and point-to-point data interfaces. The SN75158 architecture is centered on two independent differential output channels. TTL-compatible totem-pole output stages actively drive one line high while pulling the other low, allowing the differential receiver to recover the intended signal from the voltage between the pair. This arrangement supports full-duplex designs when the receive function is implemented separately and balanced, multidrop point-to-point arrangements when the cable topology and termination strategy meet the interface specifications. Typical uses include RS-422-compatible links between controllers and peripheral equipment, industrial control consoles, test equipment, telecom peripherals, and legacy instrumentation systems. Because the SN75158 is a driver rather than a complete transceiver, a separate receiver such as the SN75157 family member is required when the same endpoint must both transmit and receive. The operating temperature and 5 V supply requirements make the part especially suitable for conventional commercial equipment rather than automotive or extended-temperature systems. PCB design should preserve the balanced geometry of each differential pair and provide a continuous ground reference beneath the cable when practical. Keep the complementary outputs routed with matched impedance and avoid adding excessive stub lengths. Confirm the receiver, cable length, connector pinout, enable polarity, and termination arrangement against the complete system interface before releasing a layout. This product page combines the manufacturer's interface description with practical guidance on application fit, PCB implementation, qualification questions, and same-package alternatives. It also identifies which functions remain outside the transmitter-only device, helping engineers determine whether SN75158D is appropriate before beginning a board-level design.

RFC Hubungi kami
SN75159N - Dual RS-422/485 Driver | Texas Instruments
SN75159N

SN75159N - Dual RS-422/485 Driver | Texas Instruments

Texas Instruments SN75159N is a dual differential RS-422/RS-485 line-driver interface IC with two independently controlled outputs, 3-state operation, and a 14-pin PDIP package. It operates from a single 5 V supply and provides TTL-compatible balanced line operation for industrial data links. Each driver includes an individual output control, allowing its associated outputs to enter a high-impedance state for party-line or shared-bus arrangements. A differential line driver is an interface IC that converts logic-level signals into balanced differential outputs suitable for reliable, noise-resistant communication over cables. The SN75159 belongs to the RS-422 driver family within the broader interface-IC and bus-transceiver hierarchy. Its differential outputs help reject common-mode noise, while the 3-state capability prevents an inactive driver from loading a shared bus. The device provides two differential driver channels, single 5 V operation, TTL-compatible inputs, and independent controls for each channel. When its output-control input is low, the corresponding output pair becomes high-impedance and can neither drive nor load the bus. This behavior supports multiple transmitters sharing a party-line bus when only one driver is intended to be active at a time. The manufacturer identifies the SN75159 as meeting or exceeding ANSI EIA/TIA-422-B and ITU Recommendation V.11 requirements. The SN75159 is a driver rather than a full transceiver: it does not include receiver channels for returning data from the bus. Its 14-pin PDIP construction is appropriate for through-hole industrial, control, instrumentation, and legacy communication equipment where socketed or manually assembled DIP packaging is preferred. Because each channel can be disabled independently, the device can support multiple physical drivers on one bus when their active intervals are properly coordinated. Typical uses include industrial automation links, RS-422 point-to-point links, multidrop party-line systems, test equipment, process-control instrumentation, and data acquisition systems requiring balanced differential signaling. The 5 V supply and TTL-compatible control interface simplify connection to older logic systems, while independent channel control supports bus segmentation or spare-driver arrangements. The primary design consideration is ensuring that only one transmitter actively drives a shared bus at a time. Output-enable timing, grounding, cable termination, and driver-output loading must be evaluated together. The differential outputs should connect to the intended RS-422 network using an appropriate cable and termination scheme; the manufacturer datasheet should be consulted for the complete electrical limits and pin assignments. This page organizes the SN75159N interface function, verified operating characteristics, practical use cases, and design cautions into an engineering-focused guide. It also separates confirmed product information from parameters that require direct confirmation with the manufacturer before schematic release or production procurement.

RFC Hubungi kami