Produk (44,000+)

MAX388CWG+ - 8:1 18V Analog Multiplexer | Analog Devices
MAX388CWG+

MAX388CWG+ - 8:1 18V Analog Multiplexer | Analog Devices

Analog Devices MAX388CWG+ is a single-ended, 8-channel CMOS analog multiplexer with an 8:1 configuration, 3 kohm on-state resistance, and a 4.5V to 18V supply range. The device is offered in a 24-pin SOIC package for surface-mount instrumentation and test systems. Its eight-channel single-ended architecture lets one source be routed to eight analog inputs, while the high-voltage operating range supports signals and control circuits above conventional low-voltage logic levels. An analog multiplexer is an interface IC that connects multiple signal paths to a shared processing channel through controlled switches. The MAX388CWG+ belongs to the broader multiplexer and switch family within the semiconductor hierarchy. By selecting one of eight inputs for a common output, it can reduce the number of dedicated input channels required by a measurement, control, or signal-routing system while preserving a compact PCB footprint. Key specifications include an 8:1 multiplexing configuration, one multiplexed function, eight channels, 3 kohm on-state resistance, and operation from 4.5V to 18V. The CMOS implementation supports integration with digital control logic, while the 24-pin SOIC package is compatible with conventional surface-mount assembly. The MAX388CWG+ is identified as a commercial-temperature-grade part for general-purpose equipment applications. The MAX388CWG+ is based on a single-ended analog switching arrangement rather than a differential multiplexer. This makes it suitable when the system has one common signal bus and multiple inputs to route, provided that the source impedance and downstream amplifier account for the 3 kohm on resistance. The 4.5V to 18V supply span gives designers room for both lower-voltage precision systems and higher-voltage industrial signal environments. Typical applications include automated test equipment, data-acquisition systems, instrumentation control, industrial measurement interfaces, battery and power-system monitoring, and signal routing in industrial controllers. The eight-input structure is especially useful when a controller must inspect several sensors or conditioned analog channels through one shared converter or measurement front end. A key design consideration is that every signal passing through the selected switch sees the device's 3 kohm on-state resistance. Source impedance, amplifier bias current, capacitance, settling time, and injected noise should therefore be evaluated together. Keep routed analog traces short, maintain a common ground reference, and place input and supply bypassing close to the device to preserve measurement stability. This product page consolidates the MAX388CWG+ electrical identity, ordering-code distinction, sourcing information, and application guidance. It also provides the practical selection criteria and design considerations needed to determine whether this 8:1 CMOS multiplexer is appropriate for a particular analog-routing architecture.

RFC Hubungi kami
MAX388EPN+ - 8:1 3kOhm Analog Multiplexer | Analog Devices
MAX388EPN+

MAX388EPN+ - 8:1 3kOhm Analog Multiplexer | Analog Devices

The Analog Devices MAX388EPN+ is a fault-protected, 8-channel single-ended analog multiplexer with an 8:1 configuration, 3 kOhm on-resistance and an 18-pin PDIP package. The device uses internal data latches to hold the selected channel, allowing control signals to change the active input without disrupting the selected analog path. Its high-voltage, N-channel, P-channel, N-channel switch architecture improves fault protection when voltage remains present after the device power is removed. An analog multiplexer is an interface IC that routes one of several analog inputs to a shared output. The MAX388 family combines an 8:1 single-ended multiplexer with internal selection latches, placing it in the interface IC hierarchy alongside analog switches, mux/demux devices and signal-routing components. This makes the device useful when several sensor, measurement, or control signals must share a limited number of converter inputs. Key features include an 8:1 multiplexing ratio, 3 kOhm on-resistance and a high-voltage fault-protected architecture. The internal latches remove the need to hold a control input in a defined state after selection. The product family also provides an off behavior when power is removed but input voltages remain applied, allowing all channels to turn off and limiting unintended signal paths. The MAX388EPN+ is specifically listed in an 18-pin PDIP package. The MAX388 family uses a high-voltage series N-channel, P-channel, N-channel structure rather than a conventional single-polarity switch arrangement. This topology is specifically intended to improve fault protection in systems where external inputs can exceed the supply voltage or where power can be removed before the analog signals. The 3 kOhm on-resistance is appropriate for medium-impedance sensor and instrumentation paths, although system gain, leakage and settling requirements must be evaluated in the complete signal chain. Typical uses include multi-sensor signal selection, instrumentation measurement multiplexing, industrial control signal routing, test-equipment input selection and embedded analog measurement systems. The latched channel selection is especially useful when a host controller writes a channel address and then performs an analog conversion. In these systems, the mux reduces the number of analog input channels required at the converter while preserving a defined route through the selected switch. Designers should confirm the absolute maximum input and supply ratings, channel leakage, off isolation, on-state resistance tolerance and acquisition settling time in the manufacturer datasheet before finalizing signal paths. Input and ground connections should be arranged to minimize coupling between adjacent channels, and unused digital control inputs should be driven to valid logic levels. Because the MAX388 family is obsolete, long-life programs should verify availability, alternate sourcing and any required qualification before release to production. This product page consolidates the confirmed switch ratio, on-resistance, package, fault-protection architecture and lifecycle information with practical design guidance. It also identifies the limited number of verified drop-in alternatives, helping engineers distinguish a true pin-compatible replacement from a broader functional equivalent before modifying an existing 18-pin PCB layout.

RFC Hubungi kami
MAX389EPN+ - 4:1 Differential Multiplexer | Analog Devices
MAX389EPN+

MAX389EPN+ - 4:1 Differential Multiplexer | Analog Devices

The Analog Devices MAX389EPN+ is a dual 4:1 analog multiplexer IC with an on-resistance of 3 kOhm, supplied in an 18-pin PDIP package. It is designed as a differential multiplexer for routing analog signals while adding the fault-protection function identified in the MAX389 family documentation. The device belongs to the interface IC hierarchy and provides a practical way to connect multiple signal sources to downstream analog measurement or control circuitry. An analog multiplexer is an interface IC that selects one of several input paths and connects it to an output. A 4:1 configuration gives the MAX389EPN+ four input positions per internal switch, while the two-circuit designation identifies the two switching sections used by this differential implementation. This arrangement can reduce the number of separate signal paths required in instrumentation, test systems, and other analog-routing designs. The primary verified characteristics of the MAX389EPN+ are its dual-circuit organization, 4:1 multiplexing ratio, 3 kOhm on resistance, differential operating arrangement, industrial temperature grade, and 18-pin PDIP construction. The PDIP format uses through-hole mounting and provides generous pin spacing for laboratory, industrial control, educational, and legacy equipment designs where surface-mount assembly is not required. The MAX389 family documentation identifies these devices as high-voltage, fault-protected analog multiplexers. That positioning makes signal-path protection an important part of circuit planning because the selected switch must tolerate the voltage and fault conditions present in the intended system. Engineers should use the manufacturer datasheet for the complete absolute maximum ratings, switching characteristics, channel configuration, control logic, and truth table before finalizing a high-energy analog front end. Typical uses include routing differential sensor signals, selecting test points in automated measurement systems, multiplexing analog channels in industrial control equipment, and connecting external instrumentation to a shared processing chain. Because the verified information identifies a differential 4:1 architecture, the part is particularly relevant to circuits that need paired signal routing rather than a single-ended selector. PCB design should preserve the through-hole footprint of the 18-pin PDIP package and route sensitive analog traces away from switching nodes and other high-energy circuitry. Confirm the exact pin numbering, control inputs, common-mode limits, and maximum signal voltage in the manufacturer datasheet before fabrication. This page combines the verified device identity, package and switching characteristics with drop-in comparison information and practical guidance for industrial analog-routing designs. It distinguishes confirmed specifications from parameters that must be checked directly in the MAX389EPN+ datasheet.

RFC Hubungi kami
MAX392CSE+ - Quad SPST Analog Switch, 20 Ohm, 16-SOIC | Analog Devices
MAX392CSE+

MAX392CSE+ - Quad SPST Analog Switch, 20 Ohm, 16-SOIC | Analog Devices

The Analog Devices MAX392CSE+ is a precision quad SPST analog switch with 20 Ω typical on-resistance, 4 pC maximum charge injection and less than 1 µW of power consumption, packaged in a 16-pin SOIC (CSE) package. An analog switch, also called an analog multiplexer or solid-state relay, is a semiconductor device that routes a signal from one node to another under digital control without moving the signal physically. The MAX392 belongs to the product hierarchy analog switch > multiplexer > interface IC > integrated circuit. Each of the four independent switches in the MAX392 is a single-pole single-throw (SPST) type, so it provides a simple on/off path for analog signals rather than a multi-channel selection function. Key features of the MAX392 family include guaranteed on-resistance matching between channels below 2 Ω, on-resistance flatness over the signal range below 4 Ω, charge injection limited to 4 pC maximum, and improved off leakage of less than 2.5 nA at +85 °C. The part operates from a single +3 V to +15 V supply or from dual bipolar supplies of ±3 V to ±8 V, which allows it to sit alongside both modern low-voltage digital rails and legacy ±5 V analog instrumentation. Internally the device uses MOSFET pass elements switched by CMOS control logic, which keeps the control input compatible with standard TTL and CMOS levels. The very low power consumption of less than 1 µW per switch makes the MAX392 attractive for battery-powered and portable measurement systems where leakage and standby draw dominate the power budget. Electrostatic discharge withstand above 2000 V per Method 3015.7 protects the pins during handling and board assembly. Typical applications include precision test and measurement multiplexing, audio and low-level signal routing in instrumentation, industrial process control module switching, and general-purpose analog signal isolation in data acquisition systems. The quad SPST arrangement lets one package handle four separate signal paths, which reduces both board area and the number of control lines needed. When designing with the MAX392CSE+, pay attention to the negative rail requirement in dual-supply operation and to off-state leakage when the switched node sits near the supply rails. Place the device close to the source and destination so that trace capacitance does not degrade the small charge-injection and switching-glitch performance that make this switch precise in the first place. This page brings together parametric detail, package information, drop-in alternatives and practical design notes so that engineers can qualify the MAX392CSE+ for a precision analog switching requirement without having to piece the data together from several documents.

RFC Hubungi kami
MAX394CAP+ - Quad SPDT 35Ω Analog Switch | Analog Devices
MAX394CAP+

MAX394CAP+ - Quad SPDT 35Ω Analog Switch | Analog Devices

The Analog Devices MAX394CAP+ is a low-voltage, quad SPDT CMOS analog switch with four independently selectable 2:1 channels, a 35 Ω on-resistance, and a 20-pin SSOP package. The device supports a 5 V supply, 130 ns maximum on-time, 75 ns maximum off-time, and 200 pA maximum off leakage. These characteristics make it suitable for routing low-voltage analog signals in test, measurement, communication, and industrial control systems. A CMOS analog switch is a semiconductor device that uses MOSFETs to connect or disconnect signal paths under digital control. The MAX394 belongs to the broader analog switch and multiplexer hierarchy, which sits within interface ICs and semiconductor signal-routing components. Each SPDT channel can select one of two signal sources or route a common node to a selected destination, depending on the application and external connection arrangement. The MAX394CAP+ provides four 2:1 switch circuits with a specified 35 Ω on-resistance. Its low-voltage operation is suitable for systems using 5 V-powered logic and low-level analog signals. The 130 ns on-time and 75 ns off-time provide fast transition behavior, while break-before-make operation helps prevent two switched paths from conducting simultaneously during changeover. The 200 pA off-leakage specification supports low-level measurement and sampling circuits. The 20-SSOP package provides a compact surface-mount footprint for multiplexed analog routing. Because the package is not thermally exposed, board layout and ambient conditions remain important when multiple channels switch continuously. Signal integrity is influenced by source and load impedance, cable or trace capacitance, supply bypassing, and the timing of control signals. The device’s analog characteristics should therefore be evaluated together with the complete signal path rather than treated as isolated switch ratings. Typical uses include multimeter and oscilloscope input routing, data-acquisition systems, communication-interface signal multiplexing, automated test equipment, and industrial measurement modules. The four channels can support parallel routing or switching functions, reducing the number of discrete relays or mechanical switch elements required on a compact instrument board. The device is also useful when a circuit must select between sensors, amplifiers, or external test signals. Designers should place the supply bypass capacitor close to the device and route high-impedance signal traces away from switching-node outputs to minimize coupling. Control signals should meet the device’s input logic levels, and unused inputs should be connected to defined potentials rather than left floating. Confirm that source and load voltages remain within the device’s absolute maximum ratings and signal limits before finalizing the analog front end. This page combines the MAX394CAP+ device specifications, sourcing guidance, functional comparison, and application-focused design notes to support faster component selection and PCB implementation. It also distinguishes exact drop-in interchangeability from merely similar analog switches, helping engineers preserve package, pinout, timing, and channel requirements during redesigns.

RFC Hubungi kami
MAX395CNG+ 8-Channel SPST Analog Switch | Maxim Integrated
MAX395CNG+

MAX395CNG+ 8-Channel SPST Analog Switch | Maxim Integrated

Analog Devices MAX395CNG+ is an 8-channel, serially controlled SPST analog switch with 100 ohm on-resistance, a 2.7 V to 16 V supply range, and a 24-pin PDIP package. It combines eight independently controlled switches with a serial shift register for compact signal-routing designs. An analog switch is an electronic semiconductor device that connects or disects analog signal paths under digital control. Within the product hierarchy, the MAX395CNG+ is an analog switch IC, also described as a multiplexer or switch array. Its eight SPST channels can route low-voltage signals in test equipment, instrumentation, control systems, data acquisition, and embedded measurement products without requiring eight separate mechanical or discrete switch devices. The MAX395CNG+ uses a serial interface compatible with SPI, QSPI, and MICROWIRE protocols. Data enters at DIN and is clocked synchronously into the internal shift register on the rising edge of SCLK, allowing the eight switch states to be loaded from a host processor. The 2.7 V to 16 V operating supply supports low-voltage systems, while the cited dual-supply operating range extends from ±2.7 V to ±8 V for bipolar signal applications. Eight separately controlled SPST switches provide 1:1 routing for each channel. The manufacturer describes the MAX395 as electrically equivalent to two MAX391 quad switches controlled by a serial interface. This architecture consolidates channel control into one package and is particularly useful when a design needs multiple analog paths to share a common serial-control structure. Typical applications include automated test equipment, analog measurement systems, industrial control interfaces, programmable signal-routing boards, and compact data-acquisition equipment. The serial architecture is useful when the number of host GPIO pins is limited, while the 24-pin PDIP package simplifies prototyping, inspection, and through-hole assembly. Designers should account for the control signal levels, supply sequencing, and signal amplitudes applied to each switched node. Because the MAX395 uses edge-triggered serial loading, the host must clock the intended bit pattern in the correct order and keep SCLK stable around each rising edge. The MAX395CNG+ also requires board-space allocation for a through-hole 24-pin package rather than a compact surface-mount land pattern. This product overview combines the manufacturer's device description with practical guidance on serial control, routing architecture, package considerations, and verified drop-in alternatives. It is intended to help engineers identify whether an eight-channel serially addressed switch fits a new analog-routing design before beginning board layout.

RFC Hubungi kami
MAX395EAG+ - 8-Channel Serial SPST Switch | Analog Devices
MAX395EAG+

MAX395EAG+ - 8-Channel Serial SPST Switch | Analog Devices

The Analog Devices MAX395EAG+ is a serially controlled, 8-channel single-pole single-throw analog switch with a maximum on-resistance of 100 ohm, operating from 2.7 V to 16 V and housed in a 24-pin SSOP package. Each of its eight switches can be controlled independently through a serial shift-register interface compatible with SPI, QSPI, and MICROWIRE protocols. An analog switch is a semiconductor device that routes analog or digital signals between circuit nodes under electronic control. The MAX395 combines eight SPST switches with a serial control register, placing it in the hierarchy of analog switch, multiplexer or demultiplexer, interface IC, and semiconductor. It is useful where a microcontroller or test system must address multiple signal paths while minimizing the number of dedicated control pins. The device supports single-supply operation from 2.7 V to 16 V as well as dual-supply operation from ±2.7 V to ±8 V. Its maximum on-resistance is 100 ohm, and switching times are specified at up to 400 ns. Off leakage is 0.1 nA at +25°C and 5 nA at +85°C, helping preserve the integrity of high-impedance analog nodes during disconnected intervals. The internal serial interface shifts command data into the device on the rising edge of SCLK. Data presented at DIN is clocked into the internal shift register, where it controls the states of the eight SPST channels. According to the Analog Devices product page, the MAX395 is electrically equivalent to two MAX391 quad switches and is pin compatible with the MAX335. Typical uses include battery-powered measurement systems, automated test equipment, audio routing, industrial control interfaces, and general-purpose signal multiplexing. The serial interface reduces control-logic wiring, while the eight independently controlled channels provide flexible routing across a compact PCB footprint. Designers should account for the 100 ohm channel resistance when driving the switched nodes, especially with long PCB traces or high-frequency signals. Supply bypassing, grounded return paths, and careful routing of the serial clock and data lines are necessary to limit coupling into the analog channels. The power-up state leaves all switches off and resets the internal shift registers to zero. This page summarizes the device function, operating limits, pin-compatible family relationships, selection trade-offs, and practical integration guidance. It also organizes manufacturer information and technical alternatives to support faster component evaluation and board-level sourcing decisions.

RFC Hubungi kami
MAX396CPI+ - 16-Channel 100Ω Analog Multiplexer | Analog Devices
MAX396CPI+

MAX396CPI+ - 16-Channel 100Ω Analog Multiplexer | Analog Devices

The Analog Devices MAX396CPI+ is a precision 16-channel analog multiplexer with a 100Ω maximum on-resistance, 16:1 configuration, and a 28-pin PDIP package. It operates from a single +2.7V to +16V supply or from dual ±2.7V to ±8V supplies, making it suitable for low-voltage precision signal-routing systems. An analog multiplexer is an analog switch that connects one of several input signals to a shared output. A 16:1 device such as the MAX396CPI+ provides one common output and four binary address inputs for selecting among 16 channels. In the broader semiconductor hierarchy, it belongs to the analog switch and multiplexer family within interface integrated circuits. Its low-voltage CMOS implementation supports instrumentation, data acquisition, control, and test systems that route bipolar or single-ended signals. The MAX396 family provides maximum on-resistance of 100Ω, with resistance matching between switches maintained within 6Ω. The on-resistance remains flat within 10Ω over the specified signal range. Charge injection is limited to 5pC maximum, helping minimize switching transients in measurement paths. According to the manufacturer data sheet, the devices also provide electrostatic-discharge protection greater than 2000V using Method 3015.7. The device accepts either a single positive supply from +2.7V to +16V or dual supplies from ±2.7V to ±8V while retaining CMOS-compatible logic inputs. Switching timing is specified at 150ns, enabling the mux to serve both moderate-speed acquisition systems and precision measurement circuits. The MAX396 is offered in dual 8-channel configurations, while MAX396CPI+ is the 16-channel, 28-pin PDIP implementation. Typical uses include multiplexed sensor acquisition, programmable instrumentation, industrial control interfaces, automated test equipment, and low-level signal routing. The 100Ω on-resistance is particularly suitable for high-impedance sensors and amplifier inputs where insertion resistance must remain controlled. The low-voltage supply options also simplify systems using modern low-voltage analog and mixed-signal systems. PCB design should minimize trace resistance on muxed analog paths and keep switching-node capacitance low. Enable and address transitions should be sequenced so that unwanted channels do not connect during signal acquisition. The 28-pin PDIP footprint is also mechanically straightforward to prototype, although production designs must consider its through-hole package versus smaller surface-mount options. This page combines the manufacturer's electrical characteristics, packaging information, application guidance, pin-compatible comparisons, and practical layout considerations to support component selection and board-level implementation. It also identifies the operating limits and functional distinctions that matter when choosing between related MAX396 and MAX397 family members.

RFC Hubungi kami
MAX396EPI+ - 16:1 100Ohm CMOS Analog Multiplexer | Analog Devices
MAX396EPI+

MAX396EPI+ - 16:1 100Ohm CMOS Analog Multiplexer | Analog Devices

Analog Devices MAX396EPI+ is a precision, low-voltage CMOS analog multiplexer with one 16:1 switch, a maximum on-resistance of 100 ohms, and a 28-pin PDIP package. The device operates from a single +2.7 V to +16 V supply or from ±2.7 V to ±8 V dual supplies while maintaining compatibility with CMOS logic inputs. An analog multiplexer is an interface IC that connects multiple analog signal sources to a shared processing channel. The MAX396 belongs to the broader analog switch and multiplexer hierarchy, where switch resistance, channel matching, charge injection, leakage, and supply voltage determine how accurately a selected signal reaches the output. This makes the device suitable for precision measurement, data acquisition, test equipment, and industrial control systems. The MAX396EPI+ provides maximum on-resistance of 100 ohms, with on-resistance matching between switches maintained within 6 ohms. Its on-resistance remains flat over the specified signal range, with a maximum variation of 10 ohms. These characteristics make channel resistance less dependent on signal amplitude than in some multiplexers and support repeatable analog measurements. Charge injection is limited to 5 pC maximum. The low-voltage silicon-gate CMOS process supports low-power operation while providing fast switching. The multiplexer retains CMOS-logic input compatibility and includes electrostatic-discharge protection greater than 2,000 V per Method 3015.7. Single-supply operation supports +2.7 V to +16 V systems, while dual-supply operation permits bipolar signal ranges of ±2.7 V to ±8 V. Typical applications include multiplexed data acquisition, sensor signal routing, automated test systems, industrial measurement interfaces, and control systems that must connect several low-voltage analog inputs to one downstream converter or amplifier. Single-supply operation is convenient for compact equipment, whereas dual supplies allow the device to process signals around ground. When laying out a circuit, keep analog traces short and provide a stable ground reference. Place input and supply decoupling capacitors close to the device, and confirm that the selected signal amplitude, common-mode range, and switching frequency remain within the electrical limits of the application. This page organizes the key MAX396EPI+ specifications, pin-compatible replacement options, application guidance, and practical design considerations to support faster component selection and PCB implementation.

RFC Hubungi kami
MAX396EQI - 16:1 Precision CMOS Analog Multiplexer | Maxim
MAX396EQI

MAX396EQI - 16:1 Precision CMOS Analog Multiplexer | Maxim

The Maxim Integrated (Analog Devices) MAX396EQI is a precision 16-channel/dual 8-channel low-voltage CMOS analog multiplexer housed in a 28-pin PLCC (11.51 x 11.51 mm) package, specified over the industrial -40C to +85C temperature range. The device is built on Maxim's low-voltage CMOS process and integrates a single 16:1 mux (or two 8:1 muxes in parallel mode) with parallel address logic, making it a classic Maxim precision signal-routing building block. It is the original E-series (extended-industrial) part of the MAX396 family. What is an analog multiplexer? An analog multiplexer (mux) is a switch network that routes one of N analog input signals to a single output line under digital control. Muxes are the foundational building block of analog signal chains, sitting between sensors, test points, instrumentation amplifiers, and an ADC. The MAX396EQI specifically belongs to the CMOS analog mux family, characterized by low on-resistance, low leakage, and rail-to-rail analog signal handling - critical for instrumentation and data-acquisition front-ends. Key specifications include 100 ohm maximum on-resistance (matched within 6 ohm between channels), on-resistance flatness of 10 ohm maximum across the specified analog signal range, transition time under 250 ns, and input off-leakage current below 1 nA at +85C. These characteristics make the MAX396EQI well suited for low-distortion multiplexing of precision signals without the channel-mismatch errors that plague generic muxes. The device operates from a single +2.7V to +16V supply (or split +/- supplies), draws a low quiescent current, and provides ESD-rated inputs with TTL/CMOS-compatible address logic. Architecturally it uses charge-pump driven CMOS analog switches that keep the on-resistance flat over the analog signal range - a hallmark of Maxim's precision muxes versus competing JFET or DMOS parts. Typical applications include data-acquisition front-ends, automated test equipment (ATE) signal routing, audio signal routing, instrumentation multiplexing, and process-control analog input boards. Engineers typically pair the MAX396EQI with a precision op-amp buffer and a successive-approximation ADC to build a 16-channel low-noise analog front-end. When designing with the MAX396EQI, observe the absolute maximum analog signal range of V+ and V- rails; exceeding these destroys the switches. Use a low-ESR bypass capacitor of 0.1 uF close to the supply pin and reserve a small RC network on the address lines to suppress digital switching transients that couple into the analog path. Compared with modern pin-compatible successors, the MAX396EQI delivers superior channel matching but consumes more supply current and occupies a larger PLCC footprint than today's TSSOP muxes. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not typically consolidated on the manufacturer datasheet, helping engineers select, source, and implement the MAX396EQI more confidently.

RFC Hubungi kami
MAX397CPI+ - Dual 8:1 CMOS Analog Multiplexer | Maxim Integrated
MAX397CPI+

MAX397CPI+ - Dual 8:1 CMOS Analog Multiplexer | Maxim Integrated

The Maxim Integrated MAX397CPI+ is a precision dual 8:1 CMOS analog multiplexer with a maximum on-resistance of 100 ohms, a 28-pin PDIP package, and support for single or dual supplies. The device provides 16 switch channels organized as two 8:1 muxes, with charge injection limited to 5 pC maximum and ESD protection greater than 2,000 V under Method 3015.7. An analog multiplexer is an analog switch network that routes a selected input channel to an output terminal under digital control. In the signal-chain hierarchy, the MAX397CPI+ is a CMOS analog switch IC, also described as a 16-channel or dual 8-channel precision multiplexer. It reduces the number of external connections required when several low-frequency analog signals must share one downstream converter, amplifier, or measurement circuit. The MAX397CPI+ uses Maxim's low-voltage silicon-gate process to provide low on-resistance, tightly matched switch resistance, low charge injection, and fast switching. Its maximum on-resistance is 100 ohms, with matching between switches specified within 6 ohms. The on-resistance remains flat within 10 ohms over the specified signal range, helping preserve signal amplitude and accuracy when different channels are selected. The multiplexer accepts a single supply from +2.7 V to +16 V or dual supplies from ±2.7 V to ±8 V. CMOS-compatible logic inputs simplify control from common digital systems. These supply options allow operation from low-voltage equipment as well as higher-range instrumentation while supporting bipolar signal paths when dual supplies are used. Typical uses include battery instrumentation, data acquisition, process monitoring, automated test equipment, and mixed-signal measurement systems. The two multiplexers can monitor paired or sequential sensor channels, select test points, or route instrumentation signals while limiting the number of external converter inputs. Design around the 100-ohm maximum on-resistance because it forms a signal-dependent voltage divider with the input and load impedances. Keep control traces away from analog inputs, use a low-impedance reference for digital controls, and observe the absolute maximum supply and signal voltages listed in the manufacturer datasheet. This page combines the device's documented electrical characteristics, package information, supply options, pin-compatible alternatives, and practical design guidance. It also organizes purchasing questions around the Request a Quote workflow on this page so engineers can evaluate supply and procurement without relying on static price information.

RFC Hubungi kami
MAX398ESE+ - 8:1 100Ω CMOS Analog Multiplexer | Analog Devices
MAX398ESE+

MAX398ESE+ - 8:1 100Ω CMOS Analog Multiplexer | Analog Devices

The Analog Devices MAX398ESE+ is a precision, single 8:1 CMOS analog multiplexer with 100 Ω on-resistance, a 3 V to 15 V supply range, and a 16-pin NSOIC package. The device routes one of eight analog inputs to a common output, making it suitable for precision signal-routing, data-acquisition, sample-and-hold, and automated-test systems. Its operating-temperature range is -40°C to +85°C for the MAX398ESE+ configuration. An analog multiplexer is a semiconductor switching device that connects multiple input channels to one shared output under digital control. It belongs to the analog switch and multiplexer hierarchy, which supports the broader field of interface ICs. By reducing the number of signal paths required on a circuit board, a multiplexed architecture can simplify wiring, conserve connector space, and support sequential acquisition from multiple sensors or test points. The MAX398 family provides precision channel matching and low on-resistance variation. According to the manufacturer product information, on-resistance is matched within 6 Ω between channels, while the maximum change across the specified analog signal range is 11 Ω. These characteristics help minimize gain error and distortion when signals pass through the selected channel. The device also uses low-voltage CMOS circuitry and supports dual 4-channel operation in appropriate device configurations. The MAX398ESE+ uses address and enable controls to select the active analog path. Its 8:1 organization allows one common output to be connected sequentially to eight source signals, reducing the number of analog switches required in multichannel systems. Signal integrity depends on keeping control traces short, using a stable low-impedance reference around the selected channel, and minimizing loading on the common output. Supply bypassing and grounding are especially important when low-level signals are measured. Typical uses include audio-signal routing, battery-powered acquisition systems, automated test equipment, communication equipment, guidance and control systems, heads-up displays, military radios, PBX and PABX systems, and sample-and-hold circuits. The precision matching is valuable in data-acquisition and test systems where channel-to-channel consistency directly affects calibration accuracy and measurement repeatability. Design the MAX398ESE+ with the required 3 V to 15 V operating range in mind and account for the voltage limits of every signal routed through the mux. Check the absolute maximum ratings and pin descriptions in the manufacturer datasheet before applying signals, especially when the analog input can exceed the selected supply rail. This page combines the device architecture, operating limits, pin-level routing guidance, application analysis, and same-package replacement information to support faster component selection and PCB-level replacement decisions.

RFC Hubungi kami
MAX399CPE+ - Dual 4:1 Analog Multiplexer | Analog Devices
MAX399CPE+

MAX399CPE+ - Dual 4:1 Analog Multiplexer | Analog Devices

Analog Devices MAX399CPE+ is a precision, low-voltage CMOS analog multiplexer containing two independently controlled 4:1 circuit switches, packaged in a 16-pin PDIP. The device is designed to route analog signals by presenting a low, repeatable on-resistance while preserving channel matching across the specified signal range. Its nominal on-resistance is 100 ohms, with channel-to-channel matching within 6 ohms and a maximum on-resistance of 11 ohms as stated in the manufacturer’s device description. An analog multiplexer is an interface IC that connects one signal source to one of several destinations using digital control inputs. The MAX399 family belongs to the broader CMOS analog-switch and signal-routing hierarchy. Each internal switch provides four selectable inputs, and the two switches can be operated independently, making the device useful for channel selection, signal routing, test systems, and precision measurement front ends. Key features include dual 4:1 configuration, low-voltage CMOS operation, 100-ohm nominal on-resistance, on-resistance matching within 6 ohms, and a maximum on-resistance of 11 ohms. The two-circuit architecture allows a board to multiplex two analog channels concurrently. The 16-pin PDIP package also provides through-hole mechanical compatibility with conventional perforated-board and through-hole PCB designs. The MAX399CPE+ uses digital select logic to connect one of four inputs in each switch section to its common output. Its monolithic CMOS implementation is intended for precision signal routing, where consistent resistance between channels is important for minimizing gain error and channel-dependent measurement variation. Because this is a passive switching function, power consumption, switching speed, bandwidth, supply voltage, and logic thresholds remain central considerations when integrating the device. Typical uses include multiplexed sensor acquisition, instrumentation signal routing, automated test equipment, sample-and-hold front ends, data acquisition systems, and analog measurement boards. In a two-axis or redundant-channel acquisition circuit, the two independent switch sections can route separate analog inputs simultaneously, reducing the number of external analog switches required. Designers should verify the supply voltage, control-logic levels, signal-range limits, switching time, bandwidth, leakage, and absolute maximum ratings in the manufacturer datasheet before finalizing a circuit. Keep routed analog traces short, provide a stable ground reference, and place bypass capacitance close to the supply pins when the device operates from a supply rail. This product page combines the exact MAX399CPE+ configuration with practical selection guidance, verified interface characteristics, application-oriented design notes, and a conservative comparison of documented drop-in alternatives. It is intended to help engineers identify whether the 16-pin dual 4:1 multiplexer fits their signal-routing requirements before requesting a quotation.

RFC Hubungi kami
MAX399CSE+ - Dual 4:1 Analog Multiplexer | Analog Devices
MAX399CSE+

MAX399CSE+ - Dual 4:1 Analog Multiplexer | Analog Devices

Analog Devices MAX399CSE+ is a precision, low-voltage CMOS analog multiplexer with two 4:1 switch circuits, on-resistance below 100 ohms, and a 16-pin SOIC package. The device routes low-voltage analog signals among multiple sources while supporting the audio-signal routing, data-acquisition, test-equipment, communication, guidance-and-control, and sample-and-hold applications identified by the manufacturer. The MAX399 family is also described as pin compatible with the industry-standard DG408, DG409, DG508A, and DG509A devices. An analog multiplexer is a semiconductor switching device that connects one common signal path to one of several input or output terminals. The MAX399 uses two independent 4:1 circuits within one package, allowing two analog channels to be selected simultaneously. In the broader component hierarchy, it belongs to analog switches, then interface ICs, then semiconductor devices used to manage signal routing in electronic systems. The MAX399CSE+ therefore sits between the signal source and the downstream measurement or processing circuit. The principal performance features include on-resistance below 100 ohms and channel matching within 6 ohms. The on-resistance remains flat over the specified analog signal range, helping preserve signal amplitude relationships when different channels are selected. The low-voltage CMOS construction supports portable, battery-powered, and low-voltage data-acquisition systems where power efficiency and compact routing are important. The dual-circuit organization also reduces the number of packages needed when two independently controlled selections are required. The MAX399 family comprises precision monolithic multiplexers intended for precision analog routing rather than high-speed digital multiplexing. Its two 4:1 sections allow one common node to select among four signal paths per section. This arrangement is useful where several sources share a common amplifier, converter, measurement channel, or system bus. Because the device is monolithic, its channel matching can remain tighter than would typically be expected from separately assembled discrete analog switches. Typical uses include audio-signal routing, automated test equipment, battery-powered instruments, communication systems, guidance and control systems, heads-up displays, low-voltage data acquisition, military radios, private-branch exchanges, and sample-and-hold circuits. In an automated test system, the MAX399CSE+ can place multiple inputs in sequence on a shared measurement path. In instrumentation, it can route control or sensor signals without duplicating the front-end amplifier. In communication equipment, the dual structure can support two simultaneous routing paths within a compact board layout. For PCB design, use the manufacturer's pin-description table when assigning traces and keep analog routing paths short and appropriately shielded from switching and digital circuitry. Confirm that each selected source stays within the device's specified analog signal range and supply limits. The low on-resistance is useful for many low-voltage measurements, but system accuracy still depends on source impedance, leakage, switch timing, and the bandwidth requirements of the downstream circuit. This page combines manufacturer application guidance, package and architecture details, drop-in cross-reference options, and practical selection guidance. It is intended to help engineers identify whether the MAX399CSE+ matches a required routing architecture and how its 16-pin SOIC footprint compares with established multiplexer families.

RFC Hubungi kami
MAX399EGE - 100Ω Dual 4:1 CMOS Analog Multiplexer | ADI
MAX399EGE

MAX399EGE - 100Ω Dual 4:1 CMOS Analog Multiplexer | ADI

Analog Devices MAX399EGE is a precision, dual 4:1 CMOS analog multiplexer with eight channels, less than 100Ω on-resistance, and a 16-pin QFN (4x4 mm) package. The device combines two independently selectable 4:1 analog switches, low on-resistance, closely matched channel characteristics, and flat resistance across the specified analog signal range. A CMOS analog multiplexer is an interface IC that routes one of several analog inputs to a shared output under digital control. Within the signal-chain hierarchy, the MAX399 belongs to the analog switch and multiplexer class, where low insertion resistance, channel matching, signal-range flatness, and switching control determine how accurately a selected signal reaches downstream converters or instrumentation. The MAX398/MAX399 family provides on-resistance below 100Ω, matching between channels to within 6Ω, and on-resistance variation of no more than 11Ω across the specified analog signal range. These characteristics make the device useful when several sensors, converter outputs, or test points must be connected to a shared analog input. The EGE package is identified as a 16-QFN, 4x4 mm surface-mount option. The multiplexer's two 4:1 circuits reduce the number of external analog input connections required by a factor of four per circuit. Digital select inputs determine which source reaches each common terminal, allowing a compact ADC front end to scan multiple analog sources without requiring a separate switch for every channel. Exact channel timing, control logic, supply limits, leakage, and operating-temperature details should be confirmed in the MAX398/MAX399 manufacturer data sheet before final circuit design. Typical uses include multiplexed sensor acquisition, instrumentation inputs, signal-chain routing, automated test equipment, and analog measurement systems. It is particularly relevant where source impedance is low enough that the multiplexer's on-resistance does not dominate the measurement error and where matched resistance between channels simplifies calibration. For layout, treat every selected analog trace as a potentially high-impedance node. Keep input and output paths short, provide a quiet return path, and observe the manufacturer's guidance for bypassing and control-signal timing. Because pin names, logic levels, supply requirements, and full switching specifications are not reproduced on this page, use the official pin-description table and typical application circuit when laying out the PCB. This page combines the MAX399EGE package identity, on-resistance and matching characteristics with practical routing guidance and qualified comparisons. It also separates electrically similar devices that use different footprints from genuine pin-compatible replacements, helping engineers avoid assuming that equal switching performance guarantees a drop-in upgrade.

RFC Hubungi kami
MAX4061EUA+ Differential Microphone Preamplifier | Maxim
MAX4061EUA+

MAX4061EUA+ Differential Microphone Preamplifier | Maxim

The Maxim Integrated MAX4061EUA+ is a 1-channel Class AB differential microphone preamplifier with adjustable gain, internal microphone bias, and complete shutdown, housed in an 8-uMAX/uSOP package. The verified distributor listing identifies it as an Amplifier IC, while the manufacturer-family description identifies the MAX4060/MAX4061/MAX4062 family as differential-input microphone preamplifiers optimized for notebook and PDA audio systems. The device is intended for portable audio signal chains where a small microphone signal must be amplified while rejecting supply and common-mode noise. A microphone preamplifier is an audio amplifier IC that receives a small differential signal from an electret or differential microphone and raises it to a level suitable for downstream audio processing. In the broader electronics hierarchy, this component belongs to amplifier ICs, audio amplifiers, microphone preamplifiers, and portable audio signal-chain devices. Its differential-input architecture helps reject noise that appears equally on both microphone inputs, while adjustable gain allows the circuit to accommodate different microphone sensitivities. The verified family description specifically highlights internal bias, excellent power-supply rejection and common-mode rejection ratios, and low-noise operation. The MAX4061EUA+ additionally includes complete shutdown according to the listed family description, supporting power management in portable equipment. The distributor result identifies the amplifier as a mono, single-channel Class AB device, which is appropriate when the system processes one microphone channel rather than a stereo pair. The MAX4061EUA+ is supplied in an 8-uMAX/uSOP package according to the verified distributor result. The verified snippets do not provide the complete electrical parameter table, gain range, supply-voltage range, input impedance, noise density, or exact pin mapping. Those values must therefore be checked against the manufacturer datasheet before final circuit design. In particular, microphone bias voltage, gain-network design, supply sequencing, and shutdown control should be validated against the specific MAX4061EUA+ datasheet rather than inferred from similar family members. Typical applications include notebook microphones, PDA audio systems, portable audio devices, differential electret-microphone front ends, and compact microphone signal conditioning. The device's internal bias can simplify microphone front-end design compared with a discrete bias network, while its differential input arrangement can improve immunity to common-mode disturbance in a compact PCB. Complete shutdown can help reduce power consumption when the audio path is inactive, although the exact shutdown timing and current values are not present in the provided web data. For implementation, place the microphone input and amplifier compensation network close to the device, keep high-impedance microphone traces short, and provide local supply decoupling. Confirm the actual pinout and exposed-pad requirements from the manufacturer datasheet before layout release. This page combines the verified distributor identification, family-level manufacturer description, package information, pricing source, and application guidance while clearly identifying unavailable technical parameters rather than guessing them.

RFC Hubungi kami
MAX4063ETE+ - Diff Mic Preamp, 2-Ch, 2.4-5.5V, TQFN-16 | Maxim
MAX4063ETE+

MAX4063ETE+ - Diff Mic Preamp, 2-Ch, 2.4-5.5V, TQFN-16 | Maxim

The Maxim Integrated (Analog Devices) MAX4063ETE+ is a 2-channel differential-input microphone preamplifier optimized for high-performance portable applications, integrating two selectable inputs, differential outputs, adjustable gain, an integrated low-noise microphone bias source, and a low-power shutdown mode. Housed in a 16-pin TQFN (4x4 mm) package, it operates from a single 2.4 V to 5.5 V supply, drawing only a few milliamps and dropping to sub-microamp shutdown current for battery-friendly operation. What is a microphone preamplifier? A microphone preamplifier is an analog front-end IC that boosts the very low-amplitude signal produced by an electret or MEMS microphone (typically 10-100 mV) up to line level suitable for an ADC or codec. It sits at the bottom of the audio signal chain: microphone capsule -> microphone preamplifier -> ADC or audio codec -> DSP/baseband. The MAX4063 specifically is a differential-input preamplifier, meaning it amplifies the difference between two input signals and rejects common-mode noise - critical for portable devices where ground loops and RF interference corrupt single-ended audio. Key features include differential inputs with high common-mode rejection, an internal low-noise bias voltage for electret microphones (eliminating the need for an external resistor divider), user-adjustable gain set by an external resistor, a complete shutdown mode for power savings, and a 2.4 V to 5.5 V wide single-supply operating range. The integrated bias source removes at least one or two external components compared to discrete designs, simplifying BOM and shrinking PCB area. Technically, the MAX4063 uses a low-noise op-amp topology optimized for audio bandwidth (20 Hz to 20 kHz), with high PSRR to reject supply ripple from upstream DC-DC converters. The differential architecture rejects RF and supply noise that would otherwise corrupt the microphone signal, and the internal bias source provides a clean regulated voltage to the electret capsule. Two selectable input paths allow the system to multiplex between two microphones (e.g., main mic and headset mic). Typical applications include notebook and tablet computer microphone arrays, headset microphones, Bluetooth headsets, digital cameras with audio capture, and any portable audio device requiring differential microphone amplification with EMI/RFI rejection. The shutdown mode extends battery life in always-listening voice-trigger designs. When designing with this device, place the input series resistors and AC-coupling capacitors close to the IC pins to maximize common-mode rejection. Use the internal bias source instead of an external resistor divider to reduce noise pickup and BOM count. The shutdown pin must be driven logic-high for normal operation and logic-low to enter shutdown. This page synthesizes drop-in alternatives, design considerations, and comparison data not found in the standalone manufacturer datasheet, supporting faster component selection for portable audio designs.

RFC Hubungi kami
MAX4490AUK+T - 10MHz, 10V/us Rail-to-Rail Op Amp | Analog Devices
MAX4490AUK+T

MAX4490AUK+T - 10MHz, 10V/us Rail-to-Rail Op Amp | Analog Devices

The Analog Devices MAX4490AUK+T is a single, low-cost CMOS operational amplifier featuring a 10 MHz gain-bandwidth product, a 10 V/us slew rate, and rail-to-rail input and output operation in a 5-pin SOT-23 package. It operates from a single +2.7 V to +5.5 V supply or from dual ±1.35 V to ±2.75 V supplies, making it suitable for compact, low-voltage analog and mixed-signal designs. An operational amplifier, or op amp, is an active analog integrated circuit that amplifies the difference between two input voltages. The MAX4490 belongs to the rail-to-rail input/output amplifier family, allowing its input and output voltages to approach the supply rails. This makes it useful when the signal range and output swing requirements exceed the practical limits of conventional amplifier architectures. Key verified features include a 10 MHz gain-bandwidth product and a 10 V/us slew rate. The device can drive 2 kOhm resistive loads to within 55 mV of either supply rail and remains unity-gain stable. Its single 5-pin SOT-23 package supports space-constrained designs, while its low-cost positioning helps reduce BOM cost in production. The MAX4490AUK+T is built around a CMOS operational-amplifier architecture designed for low-voltage operation and broad input/output range. Its 10 MHz bandwidth supports signal conditioning at moderate frequencies, while the 10 V/us slew rate improves large-signal response. Rail-to-rail output capability is especially useful in battery-powered systems, sensor interfaces, and low-voltage audio or control circuits. Typical applications include portable instrumentation, sensor signal conditioning, audio preamplification, low-voltage data acquisition, and general-purpose analog control. The 2.7 V minimum single-supply operation supports designs powered from 3.3 V rails, while the 5.5 V maximum supports common 5 V systems. Designers should verify the exact pinout and package variant, maintain adequate supply bypassing, and account for the 55 mV output headroom specification when driving loads near either rail. Because the MAX4490 is listed by the manufacturer as LAST TIME BUY, sourcing plans and long-term availability should be confirmed before new production commitments.

RFC Hubungi kami
MAX456CPL+ - 8x8 Video Crosspoint Switch | Analog Devices
MAX456CPL+

MAX456CPL+ - 8x8 Video Crosspoint Switch | Analog Devices

Analog Devices MAX456CPL+ is a monolithic CMOS 8 x 8 video crosspoint switch with eight video inputs, eight outputs, 64 T-switches, and eight internal unity-gain-stable output buffers. It supports a 250 V/µs slew rate and is packaged in a 40-pin through-hole dual in-line package. The matrix can route any input to any output, or distribute one input to multiple outputs. A video crosspoint switch is an electronically controlled routing matrix used to select and distribute video signals without changing their amplitude. The MAX456 belongs to the broader analog switch and multiplexer hierarchy, combining eight input channels, eight output channels, digitally controlled switching, and buffered outputs. This integration reduces the number of discrete routing components required in professional video, broadcast, surveillance, and industrial imaging equipment. The controlled matrix contains 64 T-switches that connect eight video inputs to selected output channels. Each matrix output is connected to an internal high-speed buffer that provides 250 V/µs slew performance and unity-gain stability. The buffered architecture helps the device maintain predictable signal behavior when a source is assigned to one output or broadcast to several outputs. The MAX456 is implemented in monolithic CMOS technology, supporting a compact crosspoint function compared with a board populated from separate analog switches and buffer amplifiers. Digital control allows the routing matrix to be changed during operation, making the device useful where source selection, signal monitoring, or programmable distribution is required. The exact control-interface timing, supply range, and electrical limits are identified in the manufacturer datasheet. Typical applications include professional video switching, broadcast routing, security-camera distribution, video test equipment, industrial imaging, and multimedia systems. The eight independent input and output channels allow compact systems to centralize source selection while retaining buffered outputs for downstream displays, recorders, or transmission equipment. Designers should use the pin-description and control-interface tables in the manufacturer datasheet when assigning PCB traces. Decoupling and signal-return routing should be treated as high-speed analog layout considerations because the device combines digital control with buffered video signals. The through-hole package also requires adequate board spacing and mechanically sound interconnects compared with a surface-mount implementation. This product page consolidates the manufacturer architecture description, package information, routing use cases, and drop-in comparison information to support faster component selection. It also highlights design checks that are not obvious from a distributor catalog entry, including output-buffer behavior, fan-out considerations, and the distinction between confirmed replacements and merely similar devices.

RFC Hubungi kami
MAX458CPL - 8x4 Video Crosspoint Switch | Maxim Integrated
MAX458CPL

MAX458CPL - 8x4 Video Crosspoint Switch | Maxim Integrated

The Maxim Integrated MAX458CPL is an 8x4 video crosspoint switch with four high-speed, buffered output channels, supplied in a 40-pin plastic DIP package. It is designed for routing multiple video input signals to selectable output channels in video distribution, monitoring, and signal-routing systems. The device provides an 8-by-4 crosspoint architecture, with eight input channels and four buffered outputs, allowing several sources to be connected to the appropriate output in a controlled system. A video crosspoint switch is a routing semiconductor used to direct video signals between multiple sources and destinations. In the broader hierarchy, the MAX458CPL belongs to the interface IC family and provides a configurable signal-routing function between video sources and downstream display, processing, or monitoring equipment. Its buffered outputs are intended to preserve signal integrity when signals are routed through the switching matrix. The MAX458CPL is identified in manufacturer-related listings as the MAX458/MAX459 8x4 video crosspoint-switch family with buffers. The MAX458CPL ordering code specifies the commercial temperature grade and a 40-pin DIP package. The product is intended for through-hole PCB assembly rather than surface-mount reflow assembly. Its rectangular DIP outline provides a straightforward connection pattern for equipment with sufficient board space and a suitable through-hole footprint. Typical uses include video surveillance systems, video walls, broadcast and professional video test equipment, monitor routing, and embedded video distribution platforms. The switching matrix allows a controller to select which of eight video inputs feeds one of four buffered outputs. Designers should account for the device's legacy through-hole package, required bypassing, signal routing, grounding, and any video-level or timing constraints defined in the manufacturer datasheet. For a new design, the MAX458CPL is most appropriate when an existing 40-pin DIP footprint and an 8x4 buffered-video architecture are required. For compact or modern equipment, a surface-mount implementation may simplify board layout, but any functional substitute must be verified for pin compatibility, video bandwidth, output drive, supply requirements, control logic, and operating temperature before use. This page summarizes the available product information, package characteristics, functional architecture, sourcing details, and engineering considerations for engineers evaluating the MAX458CPL. Use the manufacturer datasheet and its pin-description table to verify signal assignments, timing, electrical limits, decoupling, and board-layout requirements before releasing a production design.

RFC Hubungi kami
MAX4850ETE+ - Dual SPDT Over-Rail Analog Switch | Analog Devices
MAX4850ETE+

MAX4850ETE+ - Dual SPDT Over-Rail Analog Switch | Analog Devices

The Analog Devices MAX4850ETE+ is a dual single-pole double-throw analog switch with over-rail signal handling, supplied in a 16-pin TQFN package measuring 3 mm by 3 mm. The verified distributor data identifies the device as a two-channel SPDT switch intended for audio and USB signal-routing applications. Its defining architecture is a pair of independently controlled analog switches that can route a common terminal to one of two switched terminals. An analog switch is a solid-state semiconductor device used to connect or disconnect signal paths under digital control. The SPDT, or single-pole double-throw, topology provides one common terminal and two selectable throws. This makes an SPDT switch useful for selecting between two sources, sharing one output with two paths, or implementing basic routing and isolation functions. MAX4850 belongs to the broader category of interface ICs and analog switch ICs within semiconductor signal-control devices. The MAX4850ETE+ combines two SPDT channels in one compact 16-TQFN package. Its over-rail signal-handling feature is specifically identified in the verified product descriptions. This feature is important in circuits where the switched voltage may extend beyond the device's normal supply-rail limits, although the exact permitted input and supply ranges were not supplied by the verified data and must be confirmed in the manufacturer datasheet before design release. The MAX4850ETE+ is applicable to audio routing, USB signal switching, and other compact interface systems in which two independent selection functions are useful. Its 3 mm by 3 mm TQFN package reduces board area compared with larger switch packages, while exposed-pad construction can improve heat transfer when the device dissipates appreciable power. Exact contact resistance, bandwidth, leakage, channel capacitance, logic thresholds, supply range, and timing values remain unavailable in the supplied records and therefore are not asserted here. Use the MAX4850ETE+ when a design requires dual SPDT switching in the compact 16-TQFN footprint and when its verified over-rail handling characteristics satisfy the signal levels involved. Designers should confirm the complete electrical limits, control-pin truth table, recommended input circuit, and exposed-pad layout against the official datasheet. The verified distributor records support availability inquiries and quote-based purchasing, but they do not provide a numerical price table or confirmed stock quantity. This page distinguishes directly verified facts from missing technical data, connects the device with appropriate audio, USB, routing, and signal-isolation use cases, and explains what engineers must verify before layout. It also records the absence of verified pin-to-pin substitute MPNs instead of presenting speculative cross-brand parts as drop-in replacements.

RFC Hubungi kami
MAX4851HETE - Quad SPST Over-Rail Switch | Analog Devices
MAX4851HETE

MAX4851HETE - Quad SPST Over-Rail Switch | Analog Devices

Analog Devices MAX4851HETE is a quad SPST analog switch with over-rail signal handling, a 2 V to 5.5 V supply range, and a 16-pin TQFN package measuring 3 mm by 3 mm. The device provides four independent single-pole, single-throw switch channels, with a stated on resistance of 4.5 ohm, turn-on time of 100 ns, turn-off time of 60 ns, and isolation of 80 dB. Its extended operating range is -40°C to +85°C. An analog switch is a semiconductor device that routes an electrical signal between external terminals under digital control. The SPST designation means each of the four channels has one signal path, while the quad configuration integrates four switches into one package. In the device hierarchy, MAX4851HETE belongs to the analog-switch, interface-IC, and semiconductor categories. This integration allows one controller to manage several independently switched signal lines on a compact circuit board. Over-rail signal handling is the principal functional distinction of the MAX4851 family. This characteristic allows the switched signal to extend beyond the nominal supply-voltage range, which is useful when a source can present a voltage above or below the switch’s normal operating rails. The 2 V to 5.5 V operating range also supports both lower-voltage and conventional 5 V system environments. The compact 16-pin TQFN package reduces PCB area compared with larger switch packages. The MAX4851HETE is designed for signal routing where rapid transitions and channel isolation matter. Its 100 ns turn-on and 60 ns turn-off times provide substantially faster switching than many mechanical relay implementations. The 80 dB isolation specification helps reduce unwanted coupling between channels, while the 4.5 ohm on resistance suits applications where moderate insertion resistance is acceptable. These characteristics position the device between low-cost mechanical relays and more specialized high-performance switch networks. Typical uses include test and measurement signal routing, industrial control interfaces, communication-line switching, instrumentation multiplexing, and embedded systems that must route external signals under firmware control. It can also support over-rail input conditioning when the controlling system has a different voltage domain. The extended -40°C to +85°C range makes it appropriate for industrial equipment where room-temperature commercial components would be insufficient. Designers should verify every signal’s absolute maximum voltage, logic threshold, and permitted over-rail condition before routing it through the switch. Input and ground connections should have low impedance paths, while unused control pins should be driven to a defined state. Because on resistance contributes insertion loss and consumes power, sensitive high-frequency or precision analog paths should be checked for bandwidth and attenuation rather than relying only on nominal transition time. This product page combines the MAX4851 family specifications, package details, sourcing information, and engineering guidance with same-package replacement analysis. It also highlights the practical distinction between fast semiconductor switching, over-rail operation, channel isolation, and the trade-offs associated with the device’s 4.5 ohm on resistance.

RFC Hubungi kami
MAX4852ETE+T - Dual SPDT Over-Rail Switch | Analog Devices
MAX4852ETE+T

MAX4852ETE+T - Dual SPDT Over-Rail Switch | Analog Devices

The Analog Devices MAX4852ETE+T is a dual SPDT analog switch with over-rail signal handling, 4.5 ohm on-resistance, and a 16-pin TQFN package measuring 3 mm by 3 mm. It supports a +2 V to +5.5 V supply range, 1.8 V-compatible logic, 135 MHz -3 dB bandwidth, and signals extending to 5.5 V even beyond the positive supply rail. An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The MAX4852 belongs to the analog-switch and multiplexer hierarchy, where SPDT means single-pole, double-throw switching. Two independently controlled switches can select one of two signal paths for each pole. Over-rail handling distinguishes this device from conventional rail-to-rail switches by allowing a signal to pass through without distortion when it exceeds the positive supply voltage. The MAX4852 provides low 4.5 ohm on-resistance, 1 microamp low supply current, and a 0.1 ns differential skew specification. Its 135 MHz -3 dB bandwidth supports high-frequency signal routing. The device is also identified as compliant with USB 2.0 full-speed and USB 1.1 signal-switching requirements, making it suitable for low-speed USB signal paths and other data-selection circuits. Internally, each SPDT switch uses CMOS-compatible control inputs and supports over-rail signal passage. According to the Analog Devices product information, the MAX4852 uses the pass-through arrangement in which a signal up to 5.5 V can pass through even when the positive supply rail is exceeded. By contrast, the MAX4852H family places the switch input into a high-impedance state when the input exceeds the supply rail. Typical uses include audio routing, USB signal selection, test and measurement systems, communication interfaces, and industrial control equipment. The two-switch configuration allows a signal source to be routed to one of two destinations or, using suitable wiring, to select between two inputs. This makes the MAX4852 useful where compact routing, low supply current, and signal handling beyond the supply rail are important. Designers should verify control-logic levels, signal amplitude, bandwidth, and on-resistance against the application before finalizing the layout. Keep routed signal traces short, use a continuous ground reference, and place bypass capacitance near the supply pins. Account for the 4.5 ohm on-resistance when calculating insertion loss, especially when driving capacitive or low-impedance downstream loads. This page combines manufacturer specifications, verified sourcing records, same-family drop-in options, application guidance, and design considerations to support faster component evaluation and PCB-level decision-making.

RFC Hubungi kami
MAX4852HETE+ Dual SPDT Analog Switch | Analog Devices
MAX4852HETE+

MAX4852HETE+ Dual SPDT Analog Switch | Analog Devices

The Analog Devices MAX4852HETE+ is a dual SPDT analog switch with over-rail signal handling, supplied in a 16-terminal TQFN surface-mount package. The device provides two independent single-pole, double-throw switching functions in one IC, supporting analog signal routing where one input must connect to one of two possible outputs. Its industrial temperature grade and surface-mount construction suit compact signal-conditioning and test equipment designs. An analog switch is a semiconductor-controlled routing component that connects or disconnects signal paths under digital control. A dual SPDT device extends this category by combining two SPDT channels in a single package. The MAX4852 belongs to the broader analog-switch and multiplexer hierarchy, where it sits between passive mechanical switching and more complex multiplexed signal-acquisition systems. Key features include two SPDT analog switches, over-rail signal handling, 16 terminals, and an exposed-pad TQFN package identified by package code HVQCCN. The square surface-mount package supports compact PCB layouts, while the exposed pad provides a thermal and ground connection when the manufacturer land pattern is followed. Analog Devices identifies the MAX4852 as being in production. The MAX4852 combines two separately controlled routing sections in one IC rather than requiring two discrete single-switch packages. Each SPDT section can direct a common signal toward one of two outputs, making the device useful for source selection, polarity routing, measurement-path switching, and signal-path isolation. Over-rail signal handling identifies the intended capability for signals extending beyond the nominal supply range, subject to the operating limits and absolute maximum ratings in the manufacturer datasheet. Typical applications include automated test equipment, data-acquisition modules, instrumentation, communication equipment, and embedded control systems where analog signals must be routed under software control. Integrating both SPDT channels into one package can simplify routing logic and reduce the number of separate switch components, although each board must still provide proper grounding, signal conditioning, and protection appropriate to its external interfaces. Designers should follow the TQFN exposed-pad land pattern and connect the pad as directed in the manufacturer datasheet. Keep sensitive analog traces away from high-current switching paths, provide a low-impedance ground reference, and verify absolute maximum voltage and current limits against the exact operating conditions. The dual architecture is useful only when both switch sections can use the same supply and ground arrangement. This page consolidates the verified MAX4852 device identity, package details, lifecycle information, application guidance, comparison criteria, and sourcing workflow into one engineering-focused reference. Use the Request a Quote form for current availability, lead time, and commercial terms.

RFC Hubungi kami