ADM3485EARZ - 3.3V 12Mbps RS-485/RS-422 Transceiver | ADI
MPN: ADM3485EARZ ✓ AktifADM3485EARZ Ringkasan
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over longer cables or electrically noisy environments. RS-485 supports multipoint half-duplex buses, while RS-422 emphasizes balanced point-to-point or multidrop links. The differential architecture reduces susceptibility to common-mode noise and allows reliable communication across a bus when termination, biasing, and grounding are implemented correctly.
The ADM3485E provides up to 12 Mbps operation from a single 3.3 V supply. Separate driver-enable and receiver-enable controls support directional control in half-duplex designs. Its ±15 kV ESD protection improves robustness against electrostatic discharge encountered during industrial installation, while low-power operation helps limit supply demand in distributed nodes. The 8-pin SOIC package also supports conventional surface-mount assembly and compact board layouts.
This transceiver family is designed for balanced data transmission over multipoint bus lines and for systems requiring controlled driver and receiver operation. The ADM3485EARZ combines a low-voltage supply requirement with a relatively high 12 Mbps data rate, making it adaptable to industrial monitoring, factory equipment, building controls, test systems, and data-acquisition networks. Its half-duplex architecture reduces the number of external interface signals compared with separate full-duplex transceivers.
PCB implementation must preserve the integrity of the differential bus. Place the transceiver close to the line-driver and receiver components, route Y and Z as a tightly coupled pair, provide the bus termination required by the topology, and keep the driver output and receiver input paths away from switching nodes. The receiver enable and driver enable inputs require deliberate control so that the bus is not driven when multiple transmitters could become active simultaneously.
For component selection, compare the ADM3485EARZ against the MAX3485EESA+, ST3485EBDR, ISL83491IBZ, and LTC2854CDD#PBF when an 8-pin surface-mount RS-485/RS-422 transceiver is required. Verify supply voltage, maximum data rate, ESD rating, shutdown behavior, enable polarity, and exact pin assignment before approving any replacement for an existing design.
Pilihan pengganti yang segera untuk ADM3485EARZ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera ADM3485EARZ (sama faktor bentuk dan kaki) — berbeza dalam Package, Supply Voltage, Product Type, Data Rate, Duplex.
MAX3485EESA+
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →ST3485EBDR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ISL83491IBZ
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LTC2854CDD#PBF
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ADM3485EARZ Spesifikasi
| Product Type | RS-485/RS-422 differential line transceiver |
| Tegangan Pemberi Arus | 3.3 V |
| Maximum Data Rate | 12 Mbps |
| ESD Protection | ±15 kV |
| Duplex Mode | Half-duplex |
| Communication Standard | EIA RS-485 and TIA/EIA RS-422 |
| Bus Configuration | Multipoint bus transmission |
| Driver Enable Control | Yes |
| Receiver Enable Control | Yes |
| Low-Power Operation | Yes |
| Kemasan | 8-pin SOIC |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin ADM3485EARZ 8-pin soic
Konfigurasi pin untuk ADM3485EARZ (8-pin soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk ADM3485EARZ.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
ADM3485EARZ patut untuk 6 aplikasis: Industrial Sensor Networks, Factory Automation Equipment, Building Control Networks, Test and Measurement Systems, Data Acquisition Equipment, Remote Monitoring Networks.
Industrial Sensor Networks
The ADM3485EARZ fits distributed industrial sensor networks that use a 3.3 V controller and balanced RS-485 wiring. Its 12 Mbps maximum data rate supports fast polling of multiple remote nodes, while the half-duplex architecture limits the number of bus-interface signals required at each endpoint. The ±15 kV ESD rating is useful in equipment exposed to electrostatic discharge during installation. Place Y and Z on a coupled pair, terminate the bus at its physical ends, and keep the enable signals controlled so only one node drives the bus at a time.
Disebarkan
Factory Automation Equipment
The ADM3485EARZ can connect motor controllers, I/O modules, and programmable equipment over an RS-485 backbone. A 12 Mbps rated interface provides ample bandwidth for command and status traffic, while separate DE and RE controls support deterministic half-duplex traffic management. Its low-power 3.3 V operation suits compact controller boards, and ±15 kV ESD protection improves resilience in electrically active production environments. Validate termination values against cable impedance and avoid long unprotected stubs, which can create reflections and disturb differential signaling.
Disebarkan
Building Control Networks
The ADM3485EARZ is appropriate for building-automation controllers, room modules, and environmental monitors using a 3.3 V RS-485 network. The 12 Mbps capability provides substantial margin for status polling and configuration updates, while the compact 8-pin SOIC simplifies surface-mount assembly. The documented ±15 kV ESD protection supports use in occupied environments where connector discharge is a concern. Bus biasing, common-mode range, grounding, and cable topology must still be checked against the exact system and environmental requirements.
Disebarkan
Test and Measurement Systems
The ADM3485EARZ can connect laboratory instruments, programmable fixtures, and data-acquisition modules to a 3.3 V controller. Its 12 Mbps rate supports rapid transfer of commands and measurement results over a balanced bus, while half-duplex operation simplifies wiring compared with separate full-duplex channels. The ±15 kV ESD rating provides additional margin around frequently connected test equipment. For long cables or laboratory environments with significant ground-potential differences, verify common-mode limits and consider whether galvanic isolation is required.
Disebarkan
Data Acquisition Equipment
The ADM3485EARZ supports compact data-acquisition units that exchange sampled data with a host controller over an RS-485 link. The 3.3 V supply requirement aligns with many embedded processors, and the 12 Mbps rate permits efficient transfer of bursts without requiring a separate full-duplex driver and receiver pair. Separate enable inputs provide clear control of bus direction, while ±15 kV ESD protection helps manage connector transients. Configure the controller to enforce turnaround time, bus ownership, and receiver settling before asserting the driver enable signal.
Disebarkan
Remote Monitoring Networks
The ADM3485EARZ is suited to remote environmental, security, and asset-monitoring nodes linked by a low-power 3.3 V controller. Its 12 Mbps rated performance provides ample headroom for short telemetry and command messages, while the half-duplex interface reduces pin count compared with full-duplex alternatives. The ±15 kV ESD protection is useful where equipment may be touched or connected in uncontrolled environments. Use qualified twisted-pair cabling, maintain consistent reference grounds where permitted, and test system behavior with the longest cable and highest node count planned for deployment.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk ADM3485EARZ — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MAX3485EESA+ | ST3485EBDR | ISL83491IBZ | LTC2854CDD#PBF |
|---|---|---|---|---|---|
| Manufacturer | Analog Devices | Maxim Integrated | STMicroelectronics | Renesas Electronics | Analog Devices |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Penyeberangsung Jelas
- 12 Mbps rated operation (vsST3485EBDR)
- ±15 kV ESD protection (vsISL83491IBZ)
- Low-power 3.3 V operation (vsMAX3485EESA+)
- Separate half-duplex enable controls (vsLTC2854CDD#PBF)
Catatan Desain
Route the Y and Z conductors as a tightly coupled differential pair, minimize stubs, and use the transceiver ground as the local reference for the interface. Place the transceiver close to the connector so discharge current has a short path into the board grounding system. Keep switching regulators, inductors, and high-current outputs away from the Y and Z traces to minimize differential noise coupling.
Enable the driver only when the node owns the bus, and allow the receiver to settle before returning the interface to receive mode. Use the manufacturer timing information to determine receiver turnaround delays. Applying termination indiscriminately to every node can overload the line driver; termination is normally placed at the two physical ends of the bus, with bias resistors placed at one location when fail-safe biasing is required.
Keep the DE and RE traces away from the differential pair and provide pull-up or pull-down resistors only where the selected control logic requires defined disabled states. Connect the transceiver ground to the interface reference ground through a short, low-impedance path. For cables longer than the laboratory bench, validate the complete topology with the intended cable length, node count, baud rate, and termination arrangement rather than relying only on the nominal 12 Mbps capability.
Maklumat Kesediaan
The manufacturer and distributor results establish the electrical function, package, and lifecycle context but do not explicitly state the requested compliance outcomes. Compliance must be confirmed from the current manufacturer product documentation or declaration before qualification.