ADM3485EARZ - 3.3V 12Mbps RS-485/RS-422 Transceiver | ADI
MPN: ADM3485EARZ ✓ AktifADM3485EARZ Genel Bakış
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over longer cables or electrically noisy environments. RS-485 supports multipoint half-duplex buses, while RS-422 emphasizes balanced point-to-point or multidrop links. The differential architecture reduces susceptibility to common-mode noise and allows reliable communication across a bus when termination, biasing, and grounding are implemented correctly.
The ADM3485E provides up to 12 Mbps operation from a single 3.3 V supply. Separate driver-enable and receiver-enable controls support directional control in half-duplex designs. Its ±15 kV ESD protection improves robustness against electrostatic discharge encountered during industrial installation, while low-power operation helps limit supply demand in distributed nodes. The 8-pin SOIC package also supports conventional surface-mount assembly and compact board layouts.
This transceiver family is designed for balanced data transmission over multipoint bus lines and for systems requiring controlled driver and receiver operation. The ADM3485EARZ combines a low-voltage supply requirement with a relatively high 12 Mbps data rate, making it adaptable to industrial monitoring, factory equipment, building controls, test systems, and data-acquisition networks. Its half-duplex architecture reduces the number of external interface signals compared with separate full-duplex transceivers.
PCB implementation must preserve the integrity of the differential bus. Place the transceiver close to the line-driver and receiver components, route Y and Z as a tightly coupled pair, provide the bus termination required by the topology, and keep the driver output and receiver input paths away from switching nodes. The receiver enable and driver enable inputs require deliberate control so that the bus is not driven when multiple transmitters could become active simultaneously.
For component selection, compare the ADM3485EARZ against the MAX3485EESA+, ST3485EBDR, ISL83491IBZ, and LTC2854CDD#PBF when an 8-pin surface-mount RS-485/RS-422 transceiver is required. Verify supply voltage, maximum data rate, ESD rating, shutdown behavior, enable polarity, and exact pin assignment before approving any replacement for an existing design.
Drop-in alternatifler için ADM3485EARZ — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller ADM3485EARZ (aynı form faktörü ve ayağa oturma) — farklı olan Package, Supply Voltage, Product Type, Data Rate, Duplex.
MAX3485EESA+
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →ST3485EBDR
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
ISL83491IBZ
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
LTC2854CDD#PBF
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
ADM3485EARZ Özellikler
| Product Type | RS-485/RS-422 differential line transceiver |
| Besleme Gerilimi | 3.3 V |
| Maximum Data Rate | 12 Mbps |
| ESD Protection | ±15 kV |
| Duplex Mode | Half-duplex |
| Communication Standard | EIA RS-485 and TIA/EIA RS-422 |
| Bus Configuration | Multipoint bus transmission |
| Driver Enable Control | Yes |
| Receiver Enable Control | Yes |
| Low-Power Operation | Yes |
| Paket | 8-pin SOIC |
| Montaj Türü | Surface mount |
ADM3485EARZ 8-pin soic Pin Yapısı Kılavuzu
ADM3485EARZ (8-pin soic paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: ADM3485EARZ.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
ADM3485EARZ için uygundur 6 uygulamas: Industrial Sensor Networks, Factory Automation Equipment, Building Control Networks, Test and Measurement Systems, Data Acquisition Equipment, Remote Monitoring Networks.
Industrial Sensor Networks
The ADM3485EARZ fits distributed industrial sensor networks that use a 3.3 V controller and balanced RS-485 wiring. Its 12 Mbps maximum data rate supports fast polling of multiple remote nodes, while the half-duplex architecture limits the number of bus-interface signals required at each endpoint. The ±15 kV ESD rating is useful in equipment exposed to electrostatic discharge during installation. Place Y and Z on a coupled pair, terminate the bus at its physical ends, and keep the enable signals controlled so only one node drives the bus at a time.
Önerilen
Factory Automation Equipment
The ADM3485EARZ can connect motor controllers, I/O modules, and programmable equipment over an RS-485 backbone. A 12 Mbps rated interface provides ample bandwidth for command and status traffic, while separate DE and RE controls support deterministic half-duplex traffic management. Its low-power 3.3 V operation suits compact controller boards, and ±15 kV ESD protection improves resilience in electrically active production environments. Validate termination values against cable impedance and avoid long unprotected stubs, which can create reflections and disturb differential signaling.
Önerilen
Building Control Networks
The ADM3485EARZ is appropriate for building-automation controllers, room modules, and environmental monitors using a 3.3 V RS-485 network. The 12 Mbps capability provides substantial margin for status polling and configuration updates, while the compact 8-pin SOIC simplifies surface-mount assembly. The documented ±15 kV ESD protection supports use in occupied environments where connector discharge is a concern. Bus biasing, common-mode range, grounding, and cable topology must still be checked against the exact system and environmental requirements.
Önerilen
Test and Measurement Systems
The ADM3485EARZ can connect laboratory instruments, programmable fixtures, and data-acquisition modules to a 3.3 V controller. Its 12 Mbps rate supports rapid transfer of commands and measurement results over a balanced bus, while half-duplex operation simplifies wiring compared with separate full-duplex channels. The ±15 kV ESD rating provides additional margin around frequently connected test equipment. For long cables or laboratory environments with significant ground-potential differences, verify common-mode limits and consider whether galvanic isolation is required.
Önerilen
Data Acquisition Equipment
The ADM3485EARZ supports compact data-acquisition units that exchange sampled data with a host controller over an RS-485 link. The 3.3 V supply requirement aligns with many embedded processors, and the 12 Mbps rate permits efficient transfer of bursts without requiring a separate full-duplex driver and receiver pair. Separate enable inputs provide clear control of bus direction, while ±15 kV ESD protection helps manage connector transients. Configure the controller to enforce turnaround time, bus ownership, and receiver settling before asserting the driver enable signal.
Önerilen
Remote Monitoring Networks
The ADM3485EARZ is suited to remote environmental, security, and asset-monitoring nodes linked by a low-power 3.3 V controller. Its 12 Mbps rated performance provides ample headroom for short telemetry and command messages, while the half-duplex interface reduces pin count compared with full-duplex alternatives. The ±15 kV ESD protection is useful where equipment may be touched or connected in uncontrolled environments. Use qualified twisted-pair cabling, maintain consistent reference grounds where permitted, and test system behavior with the longest cable and highest node count planned for deployment.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: ADM3485EARZ — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MAX3485EESA+ | ST3485EBDR | ISL83491IBZ | LTC2854CDD#PBF |
|---|---|---|---|---|---|
| Manufacturer | Analog Devices | Maxim Integrated | STMicroelectronics | Renesas Electronics | Analog Devices |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Ana Farklılayıcılar
- 12 Mbps rated operation (karşılaştırma:ST3485EBDR)
- ±15 kV ESD protection (karşılaştırma:ISL83491IBZ)
- Low-power 3.3 V operation (karşılaştırma:MAX3485EESA+)
- Separate half-duplex enable controls (karşılaştırma:LTC2854CDD#PBF)
Tasarım Notları
Route the Y and Z conductors as a tightly coupled differential pair, minimize stubs, and use the transceiver ground as the local reference for the interface. Place the transceiver close to the connector so discharge current has a short path into the board grounding system. Keep switching regulators, inductors, and high-current outputs away from the Y and Z traces to minimize differential noise coupling.
Enable the driver only when the node owns the bus, and allow the receiver to settle before returning the interface to receive mode. Use the manufacturer timing information to determine receiver turnaround delays. Applying termination indiscriminately to every node can overload the line driver; termination is normally placed at the two physical ends of the bus, with bias resistors placed at one location when fail-safe biasing is required.
Keep the DE and RE traces away from the differential pair and provide pull-up or pull-down resistors only where the selected control logic requires defined disabled states. Connect the transceiver ground to the interface reference ground through a short, low-impedance path. For cables longer than the laboratory bench, validate the complete topology with the intended cable length, node count, baud rate, and termination arrangement rather than relying only on the nominal 12 Mbps capability.
Uyumluluk Bilgisi
The manufacturer and distributor results establish the electrical function, package, and lifecycle context but do not explicitly state the requested compliance outcomes. Compliance must be confirmed from the current manufacturer product documentation or declaration before qualification.