Texas Instruments

ADS1286UB - 12-Bit 20 kHz Micropower ADC | Texas Instruments

MPN: ADS1286UB ✓ Aktif
250 µA Vdss 8-lead SOIC Package
MOQ: 1 |

ADS1286UB Ringkasan

Texas Instruments ADS1286UB is a 12-bit, 20 kHz micropower sampling analog-to-digital converter with a differential input, integrated sample-and-hold amplifier, and 8-lead SOIC package. It consumes 250 µA of supply current and provides SPI- and SSI-compatible communication over a two-wire or three-wire serial interface. These characteristics position the ADC for compact, low-power instrumentation that converts small differential sensor signals into serial digital measurements.

A sampling ADC is an analog-to-digital converter category that uses an internal sample-and-hold circuit to capture an input voltage before conversion. The ADS1286 belongs to the broader hierarchy of ADC, data converter, signal-chain IC, and power-management-aware embedded semiconductor. Differential input is particularly useful when the desired signal is smaller than supply-voltage variation or offset, because subtracting two related inputs can reject common-mode noise and reduce the influence of ground disturbances.

The principal features are 12-bit resolution, a 20 kHz sampling rate, and a typical supply current of 250 µA. The differential architecture accepts two input terminals for single-ended or differential signal conditioning, while the sampling front end converts the selected voltage into a 12-bit code. Serial interface compatibility supports connection to embedded processors, sensors, and remote measurement nodes without requiring a parallel data bus.

The ADS1286 is specifically designed for low-power acquisition rather than high-throughput conversion. Its 20 kHz maximum sampling capability supports signals up to 10 kHz under the Nyquist criterion, although the usable analog bandwidth and acquisition time must also be respected. The serial interface reduces pin count and PCB routing requirements, but conversion timing, clocking, settling behavior, reference stability, and input noise still determine practical measurement accuracy.

Typical applications include battery-powered industrial sensing, portable medical instrumentation, remote environmental monitoring, low-energy condition monitoring, and compact process-control nodes. In each case, the 250 µA supply current helps preserve battery life, while differential inputs can simplify connection to bridge sensors, resistive dividers, and current-shunt measurements. The 8-SOIC package also supports conventional surface-mount assembly.

Designers should verify the electrical limits, input range, reference requirements, and acquisition timing in the manufacturer datasheet before fixing the analog frontend. Pay particular attention to source impedance, differential input filtering, reference decoupling, and the relationship between sampling frequency and signal bandwidth. Layout should keep the analog input and reference paths short and separate digital clock activity from sensitive analog nodes.

This page combines the official TI product information with engineering-focused guidance covering low-noise acquisition, serial interfacing, power management, PCB implementation, and practical selection between documented ADS1286 family orderings. It also distinguishes verified drop-in family alternatives from options that require additional electrical review before substitution.

Pilihan pengganti yang segera untuk ADS1286UB — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera ADS1286UB (sama faktor bentuk dan kaki) — berbeza dalam Package.

Texas Instruments
Package: 8-SOIC (0.154", 3.90 mm width)

ADS1286UL/2K5

✅ Masuk Drop-In
📦 8-lead SOIC
Same documented 12-bit, 20 kHz family function and terminal layout; ordering code differs, with temperature and packing details requiring confirmation.

📋 Alternatif rujukan (tidak dalam katalog)

ADS1286U/2K5G4

✅ Masuk Drop-In
Texas Instruments
📦 8-lead SOIC
12 bit · SAR (Successive Approximation) · 1 (single-ended or differential) · 20 kSPS · 0 V to 5.3 V · 5 V · 250 uA · SPI / SSI compatible, 2- or 3-wire serial

Hubungi untuk harga

Lihat Datasheet →

ADS1286UA/2K5G4

✅ Masuk Drop-In
📦 8-lead SOIC
Same documented 12-bit, 20 kHz family function and terminal/package compatibility; suffix indicates ordering-code differences that require confirmation.

📋 Alternatif rujukan (tidak dalam katalog)

ADS1286UG4

✅ Masuk Drop-In
📦 8-lead SOIC
Same documented ADS1286 family conversion function and 8-SOIC footprint; orderable suffix details must be checked before substitution.

📋 Alternatif rujukan (tidak dalam katalog)

ADS1286UB Penilaian maksimum & Ciri-ciri Elektrik

Converter Type 12-bit sampling ADC
Pemecahkatan 12 bit
kadar sampling 20 kHz
Input Architecture Differential input
Input Count 1
Sample-and-Hold Amplifier Integrated
Arus Pemberi Arus 250 µA
Serial Interface SPI and SSI compatible
Serial Interface Wiring 2-wire or 3-wire
Kemasan 8-lead SOIC
Jenis Pemasangan Surface mount
Suhu Operasi -40 °C to +85 °C
Conversion Code Guarantee No missing codes

Panduan Konfigurasi Pin ADS1286UB 8-lead soic

Konfigurasi pin untuk ADS1286UB (8-lead soic pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai 8-lead soic untuk ADS1286UB

Tiada data garisan pin yang diperoleh untuk ADS1286UB.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

ADS1286UB patut untuk 6 aplikasis: Battery-Powered Industrial Sensors, Portable Medical Instrumentation, Remote Environmental Monitoring, Precision Process Measurement, Condition Monitoring Systems, Low-Power IoT Sensor Nodes.

🏭

Battery-Powered Industrial Sensors

The Texas Instruments ADS1286UB fits battery-powered industrial sensing nodes because it combines a 12-bit conversion resolution with a 20 kHz sampling rate and only 250 µA of supply current. A bridge sensor, resistive divider, or current shunt can feed the differential input, allowing the ADC to resolve a small signal superimposed on a larger common-mode voltage. The serial interface supports a compact two-wire or three-wire connection to a microcontroller, while the 8-SOIC package simplifies conventional surface-mount assembly. In a field-installed node, keep the ADC close to the sensor, use symmetric input routing, and decouple the supply and reference locally to preserve measurement stability.

💊

Portable Medical Instrumentation

The ADS1286UB is appropriate for portable medical measurement systems that require compact conversion, differential input, and low supply current. Its 12-bit resolution and 20 kHz sampling capability can support acquisition from pressure, temperature, or biopotential conditioning stages, although each signal requires suitable clinical signal conditioning and safety review. The 250 µA ADC supply current helps limit consumption in battery-operated equipment, and the SPI- or SSI-compatible interface avoids a wide parallel bus. Differential analog routing and a low-noise reference are particularly important when the wanted bioelectric signal is much smaller than the analog-system offset and ground disturbance.

🧩

Remote Environmental Monitoring

The ADS1286UB supports remote environmental-monitoring nodes that combine a low-power MCU with resistive or bridge-based temperature, humidity, pressure, or gas sensors. Its 250 µA supply current and 20 kHz sampling rate provide a practical balance between periodic measurement and low-duty-cycle energy use. The differential input accepts complementary sensor outputs, while SPI or SSI communication reduces the number of signals routed over a potentially long external connection. Place filtering close to the ADC pins, protect exposed sensor lines from switching noise, and use the manufacturer timing data to select an acquisition rate appropriate for slowly varying environmental signals.

⚡

Precision Process Measurement

The ADS1286UB can be used in compact process-measurement modules that acquire slow differential signals from pressure transmitters, strain bridges, or resistive transducers. Its 12-bit output provides 4096 discrete code levels, and the 20 kHz sampling capability is more than sufficient for many process variables when paired with suitable analog filtering. The ADC's low 250 µA supply current is valuable when each sensor node operates from limited power. The main design tradeoff is that switching converters and digital clocks can corrupt small sensor signals, so separate analog and digital return paths, local reference bypassing, and controlled source impedances should be treated as mandatory layout practices.

📡

Condition Monitoring Systems

The ADS1286UB fits low-power vibration, temperature, or electrical-condition monitoring modules that periodically sample a sensor analog channel. The 20 kHz maximum sampling rate supports higher-bandwidth condition signals than a conventional slow meter, while 12-bit resolution provides a practical balance between data size, conversion performance, and communication traffic. Differential input helps when the transducer produces complementary outputs or when the measurement is referenced to a sensor return. Sampling frequency, analog bandwidth, anti-alias filtering, and digital decimation should be selected together; do not treat the converter’s sampling rate as proof that every higher-frequency mechanical signal can be measured accurately.

📱

Low-Power IoT Sensor Nodes

The ADS1286UB is well matched to low-power IoT sensor nodes because it combines a 20 kHz sampling ADC, 12-bit conversion, 250 µA supply current, and a compact serial interface. The ADC can remain associated with a duty-cycled sensor frontend rather than drawing power continuously, allowing the host microcontroller to control acquisition and communication timing. Differential inputs reduce sensitivity to shared ground movement when the sensor uses a bridge or paired divider. Use short analog traces, an appropriate anti-alias filter, and stable reference layout; also confirm the exact supply operating region and acquisition timing in the manufacturer datasheet before finalizing the node architecture.

Ringkasan Produk Disebarkan

ADS1286UB Texas Instruments Dipergunakan di: Battery-Powered Industrial Sensors, Portable Medical Instrumentation, Remote Environmental Monitoring, Precision Process Measurement, Condition Monitoring Systems, Low-Power IoT Sensor Nodes ADS1286UL/2K5 Package-compatible ADS1286 family option Dipergunakan di: Battery-Powered Industrial Sensors, Condition Monitoring Systems ADS1286U/2K5 Package-compatible family ordering Dipergunakan di: Portable Medical Instrumentation, Low-Power IoT Sensor Nodes ADS1286UG4 Compatible ADS1286 family option Dipergunakan di: Remote Environmental Monitoring ADS1286UA/2K5G4 Package-compatible family ordering Dipergunakan di: Precision Process Measurement
What is the ADS1286UB?
The ADS1286UB is a Texas Instruments 12-bit, 20 kHz micropower sampling ADC with differential input, an integrated sample-and-hold amplifier, and an 8-lead SOIC package. According to the Texas Instruments ADS1286 product page, it consumes 250 µA of supply current and supports SPI- and SSI-compatible communication over a two-wire or three-wire interface. It is suited to low-power sensor acquisition, portable measurement, and remote instrumentation.
What are the key specifications of ADS1286UB that engineers should know?
The ADS1286UB combines 12-bit resolution, a 20 kHz sampling rate, differential analog input, and a typical 250 µA supply current in an 8-lead SOIC package. The Texas Instruments product page identifies SPI and SSI compatibility using two-wire or three-wire serial communication. Its integrated sample-and-hold amplifier supports direct acquisition of low-level differential signals, while the serial interface reduces PCB routing compared with a parallel ADC.
What is the operating temperature range of ADS1286UB?
The ADS1286UB is specified for an operating temperature range of -40 °C to +85 °C. The temperature rating appears in the ADS1286 ordering information, while the Texas Instruments product page identifies the 8-lead SOIC package. Confirm the complete electrical limits, reference requirements, and interface timing against the manufacturer datasheet before using the device at temperature extremes.
Where can I download the ADS1286UB datasheet PDF?
The official ADS1286 datasheet and product resources are available from Texas Instruments through the ADS1286 product page at https://www.ti.com/product/ADS1286. The same page links ordering information, technical parameters, and the ADS1286UB part details. Use the manufacturer document for the authoritative pin description, electrical characteristics, timing diagrams, and recommended application circuit.
Where can I find the ADS1286UB pinout?
The ADS1286UB pinout and pin descriptions are shown in the pin-configuration section of the Texas Instruments ADS1286 datasheet. The device uses an 8-lead SOIC package, and the product page is the appropriate starting point for obtaining that document. Use its pin-description table when assigning power, ground, analog inputs, reference connections, and serial-interface signals on the PCB.
Can ADS1286UB measure differential signals?
Yes, the ADS1286UB has a differential input and an integrated sample-and-hold amplifier. According to the Texas Instruments ADS1286 product page, its differential architecture is intended for low-power conversion of differential sensor outputs. In an instrumented bridge, shunt, or ratiometric measurement, maintaining symmetry between the input paths helps limit the effect of common-mode disturbances.
Is ADS1286UB suitable for battery-powered sensing?
The ADS1286UB is well suited to battery-powered sensing because its stated supply current is 250 µA and its maximum sampling rate is 20 kHz. The Texas Instruments product page specifically highlights the combination of micropower consumption and a two-wire serial interface for remote sensing. Actual battery life also depends on the host processor sleep strategy, reference circuitry, sensor current, and the percentage of time the ADC remains active.
What can replace the ADS1286UB?
Documented ADS1286 family orderings with the same 8-lead SOIC footprint include ADS1286UL/2K5, ADS1286U/2K5, ADS1286UA/2K5G4, and ADS1286UG4. Cross-reference information identifies these options as package- and terminal-compatible with ADS1286UB. Before replacement, confirm temperature grade, packing code, reference behavior, interface timing, and acquisition requirements against the manufacturer datasheet.
Is ADS1286UB the same as ADS1286UL/2K5?
ADS1286UL/2K5 is documented as having consistent terminals and packages with ADS1286UB, allowing replacement without changing the existing 8-SOIC circuit footprint. The parts share the ADS1286 family’s 12-bit, 20 kHz conversion function and low-power serial-interface architecture. The ordering suffixes still require review to confirm temperature grade and reel or tape-and-reel packing details before procurement.
When should I choose ADS1286UB over ADS1286U/2K5?
Choose ADS1286UB when the 8-lead SOIC device and its documented -40 °C to +85 °C operating range align with the assembly and environmental requirements. Cross-reference information identifies ADS1286U/2K5 as package- and terminal-compatible with ADS1286UB. The choice should therefore be based on ordering-code details such as packing and temperature qualification rather than a change in the ADC footprint or serial interface.
What is the best drop-in replacement for ADS1286UB?
ADS1286UL/2K5 is the closest documented drop-in candidate because cross-reference information reports consistent terminals and packages with ADS1286UB. ADS1286U/2K5, ADS1286UA/2K5G4, and ADS1286UG4 are also package-compatible family alternatives. No verified cross-manufacturer pin-to-pin equivalent was established, so a procurement substitution should remain within the documented ADS1286 family until interface and electrical characteristics are rechecked.
ADS1286UB vs ADS1286UL/2K5: which is better for a low-power sensor node?
ADS1286UB is preferable when its documented 8-SOIC ordering configuration and -40 °C to +85 °C rating meet the sensor node requirements. ADS1286UL/2K5 is documented as package- and terminal-compatible, making it the natural fallback when ADS1286UB procurement is unsuitable. Because both belong to the ADS1286 family, compare the orderable temperature, packing, and qualification details rather than expecting a different interface architecture.
Where can I buy ADS1286UB and request a quote?
Use the Request a Quote form on this page to request ADS1286UB availability, current pricing, minimum order quantity, and lead time from XAIPART. The form provides a single engineering inquiry path without requiring price assumptions or an unsupported stock claim. Confirm the complete ordering code, shipment packaging, and quantity needed before placing the order.
What is the price of ADS1286UB?
The current ADS1286UB price depends on order quantity, shipment packaging, component availability, and purchasing conditions. Submit the required quantity through the Request a Quote form on this page for a current offer. The structured pricing area can be updated when a qualifying quantity-break listing is available, so a static figure should not be used for budgeting or comparison.
What is the lead time and stock status for ADS1286UB?
ADS1286UB lead time and immediate stock status should be confirmed through the Request a Quote form on this page. The form lets you state the required quantity, shipment format, destination, and target schedule so the purchasing response reflects the actual supply condition. Do not treat a distributor landing page as a guarantee that inventory is presently allocated to your order.
How should ADS1286UB be designed into a low-noise PCB?
Place the ADS1286UB close to the sensor and ADC support components, and route differential inputs as a compact, symmetric pair. Keep the reference and supply bypass connections short, provide a clean return path, and avoid routing serial clock and data signals beneath sensitive analog inputs. Use the manufacturer datasheet for the specified input, reference, and decoupling capacitors rather than treating the 250 µA ADC current as the current drawn by the complete analog frontend.

Data referensi kejuruteraan untuk ADS1286UB — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the ADS1286UB when a design needs a 12-bit, 20 kHz differential ADC with a 250 µA supply current and an 8-lead SOIC footprint. It is particularly suitable for battery-operated sensing, remote instrumentation, and compact process-measurement nodes. ADS1286UL/2K5, ADS1286U/2K5, ADS1286UA/2K5G4, and ADS1286UG4 are documented package-compatible family options and should be considered when ordering availability, packing, or qualification requirements differ. Their suitability still depends on confirming the complete ordering codes and electrical details against the manufacturer datasheet. No verified cross-manufacturer pin-to-pin equivalent was established, so a broader replacement requires a fresh comparison of pinout, input range, reference, acquisition timing, interface protocol, and acquisition timing. If the design needs more resolution, higher throughput, lower offset, or a smaller package, changing only the MPN may not meet the application requirements.

Perbandingan dengan Gantian

Parametr Produk Ini ADS1286UL/2K5 ADS1286U/2K5 ADS1286UA/2K5G4 ADS1286UG4
Package 8-lead SOIC 8-lead SOIC 8-lead SOIC 8-lead SOIC 8-lead SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Resolution 12 bit 12 bit 12 bit 12 bit 12 bit
Sampling Rate 20 kHz 20 kHz 20 kHz 20 kHz 20 kHz
Supply Current 250 µA 250 µA 250 µA 250 µA 250 µA
Input Architecture Differential input Differential input Differential input Differential input Differential input
Serial Interface SPI and SSI compatible, 2-wire or 3-wire SPI and SSI compatible, 2-wire or 3-wire SPI and SSI compatible, 2-wire or 3-wire SPI and SSI compatible, 2-wire or 3-wire SPI and SSI compatible, 2-wire or 3-wire
Sample-and-Hold Amplifier Integrated Integrated Integrated Integrated Integrated
Ordering Code ADS1286UB ADS1286UL/2K5 ADS1286U/2K5 ADS1286UA/2K5G4 ADS1286UG4

Penyeberangsung Jelas

  • Combines 12-bit resolution with a 20 kHz sampling rate in a micropower converter (vsADS1286UL/2K5)
  • Low 250 µA supply current supports duty-cycled and battery-powered acquisition (vsADS1286U/2K5)
  • Differential input and integrated sample-and-hold amplifier simplify low-level sensor acquisition (vsADS1286UA/2K5G4)
  • SPI- and SSI-compatible interface supports flexible serial host connections (vsADS1286UG4)

Catatan Desain

Route the two differential inputs as a compact, symmetric pair and keep them away from serial clock, data, and switching-supply nodes. Place analog filtering and the ADS1286UB close to the sensor so that interference is attenuated before reaching the sampling input. Ground the analog return independently through a controlled path and use the manufacturer pin and layout guidance for the reference and bypass connections.

Select the sampling rate, analog bandwidth, and anti-alias filter as one signal chain rather than choosing them independently. The 20 kHz conversion rate does not by itself guarantee accurate measurement of a 10 kHz input because acquisition time, settling, clocking, and filter behavior also affect the result. Use the manufacturer acquisition and timing characteristics to determine the maximum valid source impedance and the required settling period.

Estimated power consumption is 0.25 mW when the ADC operates from a 1 V supply, using the stated 250 µA supply current; the actual rail voltage and active-duty-cycle fraction must be included in the final energy budget. Bypass the supply and reference at the device with the capacitance and placement specified by the manufacturer datasheet, and account for reference-current demand separately from the ADC conversion current.

Do not treat a matching 8-lead SOIC footprint as sufficient proof of interchangeability. Verify the complete ordering code, temperature grade, packing method, reference implementation, interface timing, input limits, and acquisition behavior. This is particularly important when using a family ordering as a substitute for ADS1286UB because the component suffix can encode commercial and assembly differences even when the electrical function and PCB footprint remain compatible.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The ADS1286 is a general-purpose analog-to-digital converter; automotive qualification was not established. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or the product's material declarations.

Data disahkan pada: 2026-11-09 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

ADS1286UB ADS1286UB datasheet ADS1286UB pinout ADS1286UB datasheet pdf Texas Instruments ADS1286UB ADS1286UB 12-bit ADC ADS1286UB 20 kHz ADC ADS1286UB 250 uA ADS1286UB 8-SOIC ADS1286UB equivalent ADS1286UB replacement ADS1286UB vs ADS1286UL/2K5 ADS1286UB application circuit ADS1286UB price ADS1286UB stock

Komponen dan Tanda berkaitan

Texas Instruments ADS1286UB ADS1286UL/2K5 ADS1286U/2K5 ADS1286UA/2K5G4 ADS1286UG4 analog-to-digital converter ADC sampling ADC 12-bit ADC data converter signal-chain IC semiconductor differential input sample-and-hold amplifier SPI SSI 250 µA supply current 20 kHz sampling rate 8-lead SOIC SOIC family surface-mount package battery-powered sensing industrial instrumentation medical instrumentation environmental monitoring
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ