BCM5221A4KMLG - 10/100 Ethernet PHY, 48-QFN | Broadcom
MPN: BCM5221A4KMLG ✓ AktifBCM5221A4KMLG Ringkasan
An Ethernet PHY is the physical-layer component within the Ethernet hierarchy of network interface controller, transceiver, and communications semiconductor. It converts digital Ethernet data from a MAC into signals suitable for a twisted-pair or fiber interface and converts received signals back into digital data. The BCM5221 therefore occupies the boundary between a host controller and physical network medium, allowing embedded systems to connect directly to 10/100BASE-T networks.
The device can be powered from either 2.5 V or 3.3 V and incorporates an integrated voltage regulator. Its 175 mW dissipation figure supports compact, power-conscious equipment designs. The -40°C to 85°C industrial temperature range also allows operation across commercial and industrial environments. An RMII-oriented product description and integrated regulator simplify implementation compared with a PHY requiring a larger external supply arrangement.
The BCM5221 family combines a 10/100BASE-TX/FX-capable physical layer with low-power operation and intelligent power-down states. These states are useful in systems that must reduce energy use without losing the ability to resume network operation. Exact media-interface details, clocking requirements, magnetics recommendations, and exposed-pad thermal guidance should be implemented from the pin-description table and application information in the manufacturer datasheet 5221-DS07-405-RDS.
Typical uses include industrial Ethernet controllers, embedded gateways, set-top equipment, printer electronics, automotive or transportation networking equipment, and compact communication modules. In an RMII design, the PHY connects to a network MAC or controller through its digital interface, while the analog side interfaces through magnetics to copper cabling. The 48-QFN footprint requires careful grounding and thermal design around its exposed pad.
A key implementation consideration is that Ethernet PHY performance depends on the complete signal chain, including supply filtering, magnetics, cable routing, and reference-clock quality. Follow the reference schematic and component recommendations in the manufacturer datasheet rather than treating the PHY as a standalone Ethernet interface. Confirm that the selected RMII timing, cable, and magnetics arrangement satisfies the system link budget and electromagnetic-emissions requirements.
This page combines the manufacturer datasheet, distributor product records, cross-reference findings, package information, application guidance, and drop-in replacement analysis for BCM5221A4KMLG. The comparison and design notes are intended to make footprint, voltage, interface, and sourcing decisions easier while keeping unresolved engineering details explicit.
Pilihan pengganti yang segera untuk BCM5221A4KMLG — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera BCM5221A4KMLG (sama faktor bentuk dan kaki) — berbeza dalam Product Type.
BCM5221A4KPT
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
BCM5221A4KMLG Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | Single-port Ethernet physical-layer transceiver |
| Ethernet Data Rate | 10 Mbps or 100 Mbps |
| Driver/Receiver Configuration | 1 driver / 1 receiver |
| Supply Voltage Range | 2.5 V to 3.3 V |
| Power Dissipation | 175 mW |
| Gambaran Suhu Operasi | -40°C to +85°C |
| Kemasan | 48-pin QFN |
| Jenis Pemasangan | Surface mount |
| Integrated Voltage Regulator | Yes |
| Intelligent Power-Down States | Yes |
| Media Interface | 10/100BASE-TX/FX |
| Digital Interface | RMII |
| Kiraan Pin | 48 pins |
| Channel Count | 1 channel |
Panduan Konfigurasi Pin BCM5221A4KMLG 48-pin qfn
Konfigurasi pin untuk BCM5221A4KMLG (48-pin qfn pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk BCM5221A4KMLG.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
BCM5221A4KMLG patut untuk 6 aplikasis: Embedded Linux Ethernet Gateway, Industrial Automation Controller, Network Print and Copy Equipment, Industrial IoT Sensor Gateway, Set-Top and Media Adapter, Compact Communication Module.
Embedded Linux Ethernet Gateway
The BCM5221A4KMLG fits an embedded Linux gateway requiring one 10/100 Fast Ethernet copper port. Its 10 Mbps and 100 Mbps support, one-driver/one-receiver configuration, and 2.5 V or 3.3 V supply operation align with a host processor providing the digital MAC interface through RMII. The stated 175 mW dissipation limits thermal impact compared with a typical continuously active network interface. The PHY should be placed close to the magnetics and connector, with its supply and reference components placed in accordance with the manufacturer application layout. Linux driver compatibility, cable diagnostics, EMI behavior, and exact magnetics selection must still be validated at the system level.
Disebarkan
Industrial Automation Controller
The BCM5221A4KMLG is suitable for industrial automation equipment requiring a stable 10/100BASE-T connection in a -40°C to +85°C environment. Its single-port architecture avoids unnecessary multi-channel PHY overhead, while the integrated regulator and support for either 2.5 V or 3.3 V simplify power planning. In a controller, the PHY connects the digital MAC interface to copper network circuitry through the appropriate isolation and magnetics arrangement. Layout should preserve short high-frequency return paths, isolate analog and digital grounds as directed by the manufacturer, and account for the QFN exposed pad in thermal analysis. Functional safety, surge, conducted-emissions, and industrial-network certification remain system-level validation items.
Disebarkan
Network Print and Copy Equipment
The BCM5221A4KMLG can provide the physical layer for a 10/100 Ethernet port in a printer, copier, or multifunction office device. A single Fast Ethernet link matches the common networking requirement of these products without imposing the power and area requirements of a multi-port gigabit PHY. The 175 mW device dissipation and intelligent power-down states are useful in office equipment that spends substantial time idle. The implementation should use the manufacturer's recommended magnetics, termination, reference-clock arrangement, and decoupling. Firmware must support the PHY's required status, auto-negotiation, and link-management functions while preserving compliance with the product's EMC and safety standards.
Disebarkan
Industrial IoT Sensor Gateway
The BCM5221A4KMLG is appropriate for a compact industrial IoT gateway that must bridge local processing to a 10/100 Mbps Ethernet network. Its low 175 mW power dissipation helps conserve power in panel-mounted or remotely powered equipment, and the 2.5 V or 3.3 V supply flexibility can reduce system power-tree complexity. The PHY's intelligent power-down behavior supports low-activity operating modes without abandoning link management. Place the device, magnetics, and connector in a controlled signal-chain layout, with uninterrupted return paths and minimal high-speed trace length. The gateway designer must verify wake-up timing, cable reach, surge protection, EMC margins, and network-driver behavior across temperature and voltage corners.
Disebarkan
Set-Top and Media Adapter
The BCM5221A4KMLG fits a set-top box or media adapter that needs a single wired 10/100 Ethernet connection. The device provides one driver and one receiver, avoiding the overhead of multiple channels while supporting both 10 Mbps and 100 Mbps link rates. Its 48-pin QFN construction supports compact consumer-electronics layouts, although the exposed pad and magnetics require deliberate thermal and signal-integrity planning. Use the Broadcom reference arrangement for reference-clock components, supplies, and analog network connections to minimize radiated emissions. Product-specific requirements such as secure boot, network authentication, remote diagnostics, and standby behavior should be implemented around the PHY rather than changing its electrical interface without datasheet review.
Disebarkan
Compact Communication Module
The BCM5221A4KMLG can be used inside a compact Fast Ethernet communication module that exposes a copper-network port to a host processor or controller. The 10/100 Mbps capability, integrated regulation, and 175 mW dissipation fit compact industrial and commercial modules where size and energy use are important. The 2.5 V and 3.3 V supply options can simplify interface with multiple host platforms. Designers should reserve the 48-pin footprint in the PCB before finalizing the enclosure and connector, and route the PHY-to-magnetics section away from switching nodes and noisy power-conversion areas. Thermal verification must include worst-case link activity and ambient temperature, while production testing should cover link negotiation, cable insertion, and recovery from power-down transitions.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk BCM5221A4KMLG — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | BCM5221A4KPT |
|---|---|---|
| Brand | Broadcom | Broadcom |
| Package | 48-pin QFN | 48-pin QFN |
| Product Type | Single-port Ethernet PHY | Single-port Ethernet PHY |
| Ethernet Data Rate | 10 Mbps or 100 Mbps | 10 Mbps or 100 Mbps |
| Supply Voltage Range | 2.5 V to 3.3 V | 2.5 V to 3.3 V |
| Power Dissipation | 175 mW | 175 mW |
| Driver/Receiver Configuration | 1 driver / 1 receiver | 1 driver / 1 receiver |
| Digital Interface | RMII | RMII |
| Integrated Voltage Regulator | Yes | Yes |
Penyeberangsung Jelas
- Very low stated power dissipation for a 10/100 PHY (vsBCM5221A4KPT)
- Single-port configuration keeps the interface focused (vsBCM5221A4KPT)
- Integrated regulator supports flexible supply design (vsBCM5221A4KPT)
- Documented 48-pin QFN package enables compact layouts (vsBCM5221A4KPT)
Catatan Desain
Place the PHY, magnetics, and network connector as a compact signal-chain group, and keep the RMII traces short and continuously referenced to ground. Follow the component placement and high-speed trace geometry in Broadcom datasheet 5221-DS07-405-RDS. Do not route sensitive clock or analog-network paths beneath a switching regulator or beside an LCD timing converter. A solid, quiet ground plane reduces the coupling risk that can otherwise appear as link errors or electromagnetic-emissions failures.
Treat the 48-QFN exposed pad as both an electrical connection and a thermal path. Use the manufacturer land pattern and thermal-via recommendation rather than inventing via counts, then provide sufficient top- and bottom-layer copper for the system's worst-case ambient temperature and link activity. Although the manufacturer identifies 175 mW power dissipation, a higher junction temperature can be caused by limited copper, enclosure restrictions, or adjacent heat sources. Validate the assembled thermal path under realistic airflow and enclosure conditions.
Design the 2.5 V or 3.3 V supply path so the selected rail remains within the BCM5221 operating limits under cable insertion, link activity, and neighboring circuit transients. Place the manufacturer's recommended supply-decoupling components directly at the relevant pins and use the exact values and layout from the datasheet. Confirm startup and power-down sequencing with the RMII host because abrupt rail changes can affect link detection, reference-clock startup, and system-level brownout behavior.
Use the datasheet's reference-clock, magnetics, termination, and analog-network component values without substitution based on generic Ethernet guidance. The clock and PHY-to-magnetics paths carry high-frequency content even when the negotiated data rate is only 100 Mbps. Maintain the specified return path, avoid stubs, and observe the recommended component placement. If link negotiation or EMI testing is unstable, check the clock source and reference network before changing the magnetics or PHY settings.
Maklumat Kesediaan
The Broadcom datasheet states that BCM5221 components are not designed, intended, or certified for military, nuclear, medical, mass transportation, aviation, navigation, pollution control, hazardous-substances management, or other high-risk applications. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from current manufacturer declarations.