DS90LV017ATM-NS - 600 Mbps LVDS Driver | Texas Instruments
MPN: DS90LV017ATM-NS ✓ AktifDS90LV017ATM-NS Ringkasan
An LVDS driver is a differential-signaling interface device that converts a low-voltage single-ended logic input into two complementary outputs whose voltage difference carries the data. Current-mode LVDS drivers combine high-speed operation with controlled output current, reduced power dissipation, and low electromagnetic interference. The DS90LV017A family therefore belongs to the hierarchy of interface ICs, line drivers, LVDS transceivers, and semiconductor interface components.
The device supports switching rates above 600 Mbps and uses a 3.3 V power supply. Differential skew is typically 0.3 ns and limited to 0.7 ns under specified conditions. Maximum propagation delay is 1.5 ns, helping preserve timing margin in high-speed point-to-point systems. The typical differential output swing of 355 mV and minimized short-circuit fault current support reliable operation while reducing power dissipation at elevated signaling rates.
The current-mode architecture keeps dissipation low even at high frequency and avoids the voltage-dependent behavior associated with some older driver approaches. Differential signaling also provides rejection of common-mode noise, while the compact 8-lead SOIC footprint simplifies routing from logic circuitry to a balanced connector or cable interface. The flow-through pin arrangement supports straight-through PCB signal paths and can reduce trace turns on critical high-speed links.
Typical uses include clock distribution, high-speed serial data links, industrial control interfaces, instrumentation, test-and-measurement equipment, and embedded systems that transmit one LVDS signal over a controlled point-to-point route. The driver can be paired with a compatible LVDS receiver such as the DS90LV018A, allowing a transmitting endpoint and receiving endpoint to implement a balanced differential link.
PCB implementation should preserve a short, continuous differential path with closely matched trace lengths and a continuous ground reference. Decoupling capacitors should be connected directly between the supply and ground pins. The differential output should terminate according to the receiver and transmission-line requirements rather than adding arbitrary resistive loading that could increase edge degradation or reduce signal margin.
This page combines the manufacturer's interface specifications with practical package, timing, application, and replacement guidance. It also highlights the distinction between electrically equivalent orderable variants and the conditions under which a same-footprint substitution preserves signal timing, supply requirements, and board-level implementation.
Pilihan pengganti yang segera untuk DS90LV017ATM-NS — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera DS90LV017ATM-NS (sama faktor bentuk dan kaki) — berbeza dalam Package, Short-Circuit Fault Current.
DS90LV017ATM
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →DS90LV017ATM/NOPB
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DS90LV017AM
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
DS90LV017AMX
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
DS90LV017ATMX/NOPB
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
DS90LV017ATM-NS Spesifikasi
| Product Type | Single LVDS differential line driver |
| Number of Channels | 1 channel |
| Logic Input Style | 1/0 driver |
| Maximum Data Rate | >600 Mbps |
| Frekuensi Klock Maksimum | >300 MHz |
| Tegangan Pemberi Arus | 3.3 V |
| Typical Differential Output Swing | ±355 mV |
| Typical Differential Skew | 0.3 ns |
| Maximum Differential Skew | 0.7 ns |
| Maximum Propagation Delay | 1.5 ns |
| Output Architecture | Current-mode differential driver |
| Short-Circuit Fault Current | Minimized; exact current not stated |
| Kemasan | 8-lead SOIC |
| PCB Layout | Flow-through pin arrangement |
| Jenis Pemasangan | Surface mount |
Konfigurasi Pin DS90LV017ATM-NS
| Pin 1 | VCC — Positive supply connection |
| Pin 2 | IN — Single-ended data input |
| Pin 3 | EN — Driver enable input |
| Pin 4 | GND — Ground connection |
| Pin 5 | NC — Not connected |
| Pin 6 | OUT- — Inverting differential output |
| Pin 7 | OUT+ — Non-inverting differential output |
| Pin 8 | NC — Not connected |
Aplikasi Biasa
DS90LV017ATM-NS patut untuk 6 aplikasis: High-Speed Point-to-Point Data Links, Clock Distribution, Industrial Control Interfaces, Test and Measurement Instrumentation, Instrumentation and Sensor Signal Paths, Embedded Serial Communication.
High-Speed Point-to-Point Data Links
The DS90LV017ATM-NS fits point-to-point digital links that require data rates above 600 Mbps but only one transmitted differential signal. Its current-mode architecture supports low power dissipation at high frequency, while the typical 355 mV differential swing provides a compact LVDS interface. The 0.3 ns typical differential skew and 1.5 ns maximum propagation delay help preserve source-to-sink timing margin. Place the driver near the transmitting logic, route the differential pair over a continuous reference plane, and pair it with a compatible receiver such as the DS90LV018A.
Disebarkan
Clock Distribution
The DS90LV017ATM-NS is suitable for transmitting a high-frequency differential clock when edge-to-edge alignment is important. It supports signaling above 300 MHz, with differential skew typically limited to 0.3 ns and to 0.7 ns under the manufacturer's maximum specification. Its 3.3 V current-mode output reduces power dissipation as clock activity increases. Use short matched traces, maintain a continuous ground reference, and include receiver and connector delays in the system-level skew budget.
Disebarkan
Industrial Control Interfaces
The DS90LV017ATM-NS can provide the transmitter side of a noise-resistant balanced link in industrial control equipment. LVDS differential signaling rejects common-mode disturbance better than a single-ended interface, while the greater-than-600-Mbps capability supports high-rate command or status channels. The 3.3 V supply and compact 8-lead SOIC package simplify integration near control logic. Keep the differential pair tightly coupled, provide local supply bypassing, and verify cable, connector, and receiver characteristics in the final channel.
Disebarkan
Test and Measurement Instrumentation
The DS90LV017ATM-NS suits test and measurement modules that must transfer timing-sensitive data over a balanced cable or board-level channel. Its 0.3 ns typical differential skew and 1.5 ns maximum propagation delay support deterministic timing analysis, while the current-mode output maintains low dissipation at high data activity. The flow-through 8-lead SOIC arrangement also supports compact routing. Designers should still account for probe loading, connector transitions, cable loss, and the selected receiver's input threshold.
Disebarkan
Instrumentation and Sensor Signal Paths
The DS90LV017ATM-NS can transmit data from a remote instrumentation or sensor module where the cable may encounter electrical noise. Differential current-mode signaling provides a typical ±355 mV output and supports rates above 600 Mbps for high-resolution measurement data. Its compact 8-lead SOIC package and flow-through layout reduce routing complexity near sensor-processing logic. Use a receiver with suitable input thresholds, terminate as required by the channel design, and preserve closely matched differential impedance throughout the cable and connector transition.
Disebarkan
Embedded Serial Communication
The DS90LV017ATM-NS is appropriate for embedded systems that require a fast, balanced, point-to-point communication channel between two circuit boards. The greater-than-600-Mbps capability accommodates serialized data while differential signaling improves common-noise tolerance. A 3.3 V current-mode driver limits power dissipation as transfer activity rises, and the 8-lead SOIC package supports compact layouts. Choose a compatible receiver, preserve impedance continuity across connectors or flex circuits, and include board skew in the timing specification.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk DS90LV017ATM-NS — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | DS90LV017ATM | DS90LV017ATM/NOPB | DS90LV017AM | DS90LV017AMX | DS90LV017ATMX/NOPB |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC |
| Product Type | Single LVDS differential driver | Single LVDS differential driver | Single LVDS differential driver | Single LVDS differential driver | Single LVDS differential driver | Single LVDS differential driver |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Maximum Data Rate | >600 Mbps | >600 Mbps | >600 Mbps | >600 Mbps | >600 Mbps | >600 Mbps |
| Maximum Clock Frequency | >300 MHz | >300 MHz | >300 MHz | >300 MHz | >300 MHz | >300 MHz |
| Typical Differential Skew | 0.3 ns | 0.3 ns | 0.3 ns | 0.3 ns | 0.3 ns | 0.3 ns |
| Maximum Differential Skew | 0.7 ns | 0.7 ns | 0.7 ns | 0.7 ns | 0.7 ns | 0.7 ns |
| Maximum Propagation Delay | 1.5 ns | 1.5 ns | 1.5 ns | 1.5 ns | 1.5 ns | 1.5 ns |
| Typical Differential Output Swing | ±355 mV | ±355 mV | ±355 mV | ±355 mV | ±355 mV | ±355 mV |
Penyeberangsung Jelas
- High-speed single-channel LVDS performance (vsDS90LV017ATM)
- Controlled differential edge timing (vsDS90LV017ATM/NOPB)
- Low-power current-mode output (vsDS90LV017AM)
- Compact 8-lead SOIC implementation (vsDS90LV017AMX)
Catatan Desain
Route OUT+ and OUT- as a closely coupled differential pair over a continuous ground plane. Avoid changing layer, adding stubs, or breaking symmetry between the outputs. The manufacturer's flow-through package arrangement is intended to support straight routing, so orient the device to minimize trace turns and keep the driver close to the logic source.
Do not treat the LVDS output as a conventional single-ended logic output or add an arbitrary resistive load at the transmitter. Use the termination required by the receiver and transmission-line configuration. Account for connector and cable impedance, receiver thresholds, and differential skew when calculating system timing; the device's 0.7 ns maximum differential skew is only one part of the total budget.
Connect the 3.3 V supply through a short, low-impedance trace and place the bypass capacitor directly between VCC and GND. Follow the manufacturer's pin-description and decoupling recommendations during PCB implementation. This is especially important because a supply disturbance at a greater-than-600-Mbps data rate can reduce receiver eye margin even when the LVDS differential amplitude is nominal.
Maklumat Kesediaan
Compliance status was not established for the exact DS90LV017ATM-NS orderable code. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations against the manufacturer documentation for the selected suffix before production release.