ISL83488IB - 3.3V 250kbps RS-485/RS-422 Transceiver | Renesas
MPN: ISL83488IB ✓ AktifISL83488IB Ringkasan
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over cables or PCB interconnects. RS-485 supports multipoint bus networks with driver-enable control, while RS-422 generally describes a point-to-point differential interface. The ISL83488 family supports both standards, and its full-duplex configuration avoids multiplexing the transmitter and receiver through a shared bus.
The primary operating characteristics are a 3.3V power supply, a maximum data rate of 250kbps, and one transmit and one receive channel in an 8-SOIC package. Slew-rate limiting reduces the high-frequency content of the driver output, which can help limit EMI and reflections on longer interconnects. The receiver converts the differential bus voltage into a single-ended logic output for the host controller.
Technically, the ISL83488 is a BiCMOS interface device optimized for low-power, 3.3V balanced communication. The ISL83488 and related ISL83490 devices use separate receive and transmit paths, while the ISL83488 configuration is intended for applications that do not require independent receiver and transmitter output-disable functions. Its 250kbps rate favors noise-limited data links over high-speed differential communication.
Typical uses include industrial control links, test and measurement systems, building automation equipment, point-to-point sensor interfaces, and embedded serial networks. The full-duplex arrangement is particularly useful where the master must receive a response while transmitting a command, or where a node communicates over a dedicated balanced pair rather than a shared multidrop bus.
PCB design should preserve the differential signal path, connect the transceiver ground reference close to the device, and provide controlled termination appropriate to the cable length and topology. Disable functions and bus direction control must be handled by the host circuitry when the selected family member does not provide dedicated enable pins. Confirm the exact pin assignments and termination strategy against the manufacturer datasheet before layout release.
This product record combines the device function, package and operating characteristics with practical interface-design guidance, verified replacement analysis, and an engineering-focused comparison of directly related ISL83488-family transceivers.
Pilihan pengganti yang segera untuk ISL83488IB — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera ISL83488IB (sama faktor bentuk dan kaki) — berbeza dalam Package, Product Type, Maximum Data Rate, Supported Standards.
ISL83488IB-T
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ISL83490IB
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →ISL83491IB
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →ISL83488IBZ
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ISL83488IB Spesifikasi
| Product Type | Full-duplex RS-485/RS-422 transceiver |
| Tegangan Pemberi Arus | 3.3 V |
| Maximum Data Rate | 250 kbps |
| Driver Configuration | 1 transmitter |
| Receiver Configuration | 1 receiver |
| Duplex Mode | Full duplex |
| Supported Standards | RS-485 and RS-422 |
| Process Technology | BiCMOS |
| Output Slew Rate | Slew-rate limited |
| Kemasan | 8-lead SOIC |
| Kiraan Pin | 8 pins |
| Jenis Pemasangan | Surface mount |
| Gambaran Suhu Operasi | -40°C to +85°C |
| Automotive Qualification | Not applicable; commercial interface IC |
Panduan Konfigurasi Pin ISL83488IB 8-lead soic
Konfigurasi pin untuk ISL83488IB (8-lead soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk ISL83488IB.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
ISL83488IB patut untuk 6 aplikasis: Industrial Point-to-Point Control Links, RS-422 Sensor and Instrumentation Links, Building Automation and Environmental Control, Test and Measurement Data Acquisition, Embedded Serial Gateways, Balanced Communication in Portable Equipment.
Industrial Point-to-Point Control Links
The ISL83488IB fits dedicated controller-to-controller links where a 3.3V system needs simultaneous balanced transmission and reception at rates up to 250kbps. Its full-duplex arrangement keeps the driver and receiver on separate paths, avoiding direction multiplexing and simplifying request-response exchanges. The slew-rate-limited output also helps control high-frequency content on industrial cables. Designers should use the manufacturer application circuit for decoupling, differential routing, and termination, and should validate conducted and radiated emissions for the completed enclosure and cable configuration.
Disebarkan
RS-422 Sensor and Instrumentation Links
The ISL83488IB is appropriate for RS-422 measurement systems that need a 3.3V, 250kbps differential data path and full-duplex operation. Separate transmit and receive channels allow the controller to command an instrument while simultaneously receiving measurement data. Because the interface is not isolated, applications requiring galvanic separation need external isolation and an appropriately designed isolated power path. Cable length, grounding strategy, and termination must be evaluated together to prevent loss of differential signaling.
Disebarkan
Building Automation and Environmental Control
The ISL83488IB can connect low-speed building-control equipment over a dedicated balanced pair while operating from a 3.3V controller supply. A 250kbps slew-rate-limited link is suitable for command and status traffic, and full duplex permits simultaneous sensor reporting and actuator control. In a building network with multiple cable runs, keep each differential pair routed as a controlled impedance pair and apply termination only where required by the physical topology. Verify the operating temperature requirement against the intended installation environment.
Disebarkan
Test and Measurement Data Acquisition
The ISL83488IB supports bench and laboratory equipment that exchanges commands and results over a balanced serial connection. The 250kbps rate provides adequate throughput for many instrument-control protocols, while full-duplex operation removes the need to switch a shared transceiver direction. The 3.3V supply also simplifies integration with modern mixed-signal controllers. For high-accuracy analog measurement systems, keep the transceiver supply and digital return path separate from sensitive analog grounds where possible, and use controlled impedance routing between the IC and connector.
Disebarkan
Embedded Serial Gateways
The ISL83488IB is useful in an embedded gateway that must bridge a 3.3V host processor to a balanced industrial bus. Its single full-duplex channel supports simultaneous host commands and peripheral responses at up to 250kbps, while the slew-rate-limited driver favors controlled transitions over long interconnect paths. Firmware must manage protocol timing, fault detection, and bus state even though the family member does not require every output-disable function used by half-duplex alternatives. Protective circuitry should be selected separately for exposed cables.
Disebarkan
Balanced Communication in Portable Equipment
The ISL83488IB can support a compact 3.3V peripheral that communicates with a host through a short balanced cable. Its 8-SOIC package and full-duplex architecture permit separate receive and transmit connections, while the 250kbps rate is suitable for command, status, and low-volume sensor traffic. Portable products still need careful grounding because the interface is non-isolated. Keep the connector return close to the cable reference, route the differential pair as a pair, and evaluate ESD protection at the external interface without degrading signal integrity.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk ISL83488IB — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | ISL83488IB-T | ISL83490IB | ISL83491IB | ISL83488IBZ |
|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
| Duplex Mode | Full duplex | Full duplex | Full duplex | Full duplex | Full duplex |
| Transmitter Count | 1 | 1 | 1 | 1 | 1 |
| Receiver Count | 1 | 1 | 1 | 1 | 1 |
| Supported Standards | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
| Process Technology | BiCMOS | BiCMOS | BiCMOS | BiCMOS | BiCMOS |
Penyeberangsung Jelas
- Direct full-duplex architecture without half-duplex multiplexing (vsISL83485IBZ)
- 3.3V operation supports direct integration with low-voltage controllers (vsISL83490IB)
- Documented same-family ordering option with identical core interface (vsISL83488IB-T)
Catatan Desain
Route each differential pair as a tightly coupled, controlled-impedance pair from the transceiver to the connector. Keep the two conductors over a continuous reference plane, minimize stub branches, and avoid crossing digital return-current paths on adjacent layers. Place the device close to the interface connector so transient-energy and common-mode currents do not traverse sensitive logic areas.
Place the manufacturer's recommended supply and bypass capacitors immediately across the device power and ground pins. Keep the high-frequency return current within the capacitor connection loop and avoid routing driver-return currents through the receiver reference path. This separation is particularly important because the transceiver combines a switching-edge output stage with a differential input that responds to small signal imbalances.
Do not assume that a family member with the same 8-SOIC outline is electrically interchangeable. ISL83488, ISL83490, and ISL83491 can differ in enable or output-disable behavior, so compare the pin-description table, driver and receiver disable timing, and electrical limits before substitution. Also verify the ordering suffix and delivery configuration to avoid receiving an unexpected package format.
Use the 250kbps slew-rate-limited output for the intended balanced link and retain the manufacturer's recommended termination arrangement. Proper common-mode behavior depends on cable balance, connector grounding, and stub control; termination alone cannot correct a poor ground reference. Validate the finished system for emissions and ESD immunity because the transceiver itself does not provide galvanic isolation.
Maklumat Kesediaan
The device is a commercial RS-485/RS-422 interface IC rather than an automotive-qualified component. Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation or declaration.