Texas Instruments

DS90LV028ATMX - Dual LVDS Receiver | Texas Instruments

MPN: DS90LV028ATMX ✓ Aktif
3.3 V Vdss 8-SOIC Package 200 MHz Speed
MOQ: 1 |

DS90LV028ATMX Ringkasan

The Texas Instruments DS90LV028ATMX is a dual CMOS differential line receiver designed for low-power, low-noise LVDS data links, supporting data rates in excess of 400 Mbps, equivalent to 200 MHz, in an 8-pin SOIC package. It accepts differential input signals of approximately 350 mV typical amplitude and translates each differential pair into a CMOS-compatible output.

An LVDS receiver is an interface IC that recovers a digital signal from two complementary low-voltage differential conductors. LVDS, or Low Voltage Differential Signaling, reduces signal amplitude and common-mode interference compared with single-ended signaling. This dual receiver belongs to the broader line-receiver and interface-IC hierarchy used to connect high-speed digital sources to CMOS processors, FPGAs, transceivers, and communications equipment.

The DS90LV028A family emphasizes low power dissipation, low noise, and high data rates. Its dual-channel architecture can receive two independent differential signals in one package. A nominal 3.3 V supply supports integration with 3 V CMOS systems, while the 350 mV typical differential input aligns with standard LVDS signaling. The 8-SOIC package provides a compact surface-mount footprint suitable for communication cards and embedded control systems.

Internally, the receiver converts small differential voltages into stable CMOS logic levels. Differential reception rejects noise that appears equally on both input conductors, improving signal integrity in cable, backplane, and point-to-point environments. The two-channel organization allows one receiver package to support paired data paths, reducing component count compared with separate single-channel receivers when board area is constrained.

Typical uses include receipt of high-speed LVDS links between boards, recovery of differential clock or data signals, and interfacing LVDS links to CMOS processors, FPGAs, and communications controllers. The device can also be paired with a compatible dual LVDS driver, such as the DS90LV027A, in systems that transmit and receive differential data over a balanced connection.

When laying out the receiver, route the differential pair as a tightly coupled pair, minimize stub branches, and use controlled-impedance PCB geometry. Keep the receiver close to the connector or source when practical, because added trace length and mismatched routing can reduce signal margin. Decoupling capacitors should be placed close to the supply and ground pins to limit transient supply noise.

This page combines the manufacturer device description, interface characteristics, cross-reference options, and practical PCB guidance into a compact engineering reference. The comparison table separates documented electrical ratings from unresolved parameters, helping designers evaluate replacement candidates without overlooking pin compatibility, supply voltage, or application-specific requirements.

Pilihan pengganti yang segera untuk DS90LV028ATMX — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera DS90LV028ATMX (sama faktor bentuk dan kaki) — berbeza dalam Device Type, Package, Signaling Standard, Supply Voltage.

Texas Instruments
Device Type: Dual differential line receiver (LVDS)
Signaling Standard: LVDS (Low Voltage Differential Signaling)
Supply Voltage: 3.3 V (3-V LVDS)
Bandingkan Dengan DS90LV028ATMX →
Texas Instruments
Package: 8-pin SOIC
Signaling Standard: Low Voltage Differential Signaling (LVDS)
Bandingkan Dengan DS90LV028ATMX →

DS90LV028ATM/NOPB

✅ Masuk Drop-In
📦 8-SOIC
Same documented dual CMOS receiver class, 3.3 V nominal supply, and greater-than-400-Mbps capability; ordering suffix differs with 0% stated core-rating difference.

📋 Alternatif rujukan (tidak dalam katalog)

DS90LV028ATM

✅ Masuk Drop-In
Texas Instruments
📦 8-SOIC
Dual CMOS differential line receiver · 2 channels · Low Voltage Differential Signaling (LVDS) · 400 Mbps (200 MHz) · 350 mV · 3 V · 1.5 ns · 9 mA

Hubungi untuk harga

Lihat Datasheet →

DS90LV028ATMXN

✅ Masuk Drop-In
📦 8-SOIC
Same DS90LV028A receiver family and 8-SOIC format; 0% documented difference in the identified core ratings, with suffix-specific order details requiring confirmation.

📋 Alternatif rujukan (tidak dalam katalog)

ADN4664BRZ

✅ Masuk Drop-In
📦 8-SOIC
Cross-reference-listed dual LVDS receiver in the same 8-SOIC class; core data-rate difference is not quantified in the cross-reference listing, so verify it is within 30%.

📋 Alternatif rujukan (tidak dalam katalog)

STLVDS9637BD

✅ Masuk Drop-In
📦 8-SOIC
Cross-reference-listed dual LVDS receiver in the same 8-SOIC class; core data-rate difference is not quantified in the cross-reference listing, so verify it is within 30%.

📋 Alternatif rujukan (tidak dalam katalog)

DS90LV028ATMX Spesifikasi

Device Type Dual CMOS differential line receiver
Channel Count 2 channels
Logic Technology CMOS
Tegangan Pemberi Arus 3.3 V
Minimum Data Rate Greater than 400 Mbps
Frekuensi Klock Maksimum 200 MHz
Differential Input Signal 350 mV typical
Suhu Operasi -40 C to +85 C
Kemasan 8-SOIC
Kiraan Pin 8 pins
Jenis Pemasangan Surface mount

Panduan Konfigurasi Pin DS90LV028ATMX 8-soic

Konfigurasi pin untuk DS90LV028ATMX (8-soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 8-soic untuk DS90LV028ATMX

Tiada data garisan pin yang diperoleh untuk DS90LV028ATMX.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

DS90LV028ATMX patut untuk 6 aplikasis: High-Speed Board-to-Board LVDS Links, FPGA and Processor LVDS Interfaces, Industrial Data Acquisition Equipment, Telecommunications and Network Equipment, Clock and Data Recovery Links, Medical and Instrumentation Signal Interfaces.

🖥️

High-Speed Board-to-Board LVDS Links

The DS90LV028ATMX fits receive points on compact board-to-board links because it recovers two LVDS signals while operating above 400 Mbps and accepting approximately 350 mV differential input. Place the device near the connector or source termination to minimize trace loss and preserve timing margin. The two channels support paired communication paths in one 8-SOIC package, reducing component count while maintaining a standard 3.3 V CMOS supply. PCB routing should use a coupled differential pair, controlled impedance, and no unterminated stubs.

⚡

FPGA and Processor LVDS Interfaces

The DS90LV028ATMX is useful when an FPGA or processor lacks native LVDS input but requires high-speed differential reception. Its greater-than-400-Mbps capability, corresponding to operation above 200 MHz, supports clock and data paths, while the dual receiver architecture can recover two related channels. The CMOS output interface operates from a nominal 3.3 V supply, simplifying integration with compatible digital logic. Validate output timing, input thresholds, and system skew against the FPGA or processor specifications before finalizing the interface.

🏭

Industrial Data Acquisition Equipment

Industrial measurement and acquisition equipment can use the DS90LV028ATMX to receive low-amplitude differential signals arriving from remote sensors, converters, or test fixtures. Differential reception helps reject common-mode noise encountered in industrial environments, while the device's low-power, low-noise design supports compact multi-channel instruments. Its -40 C to +85 C specified operating range covers many industrial ambient conditions. Design the analog front end and cable return path so differential amplitude and common-mode limits remain within the receiver's electrical requirements.

🌐

Telecommunications and Network Equipment

The DS90LV028ATMX can terminate high-speed LVDS connections inside line cards, interface modules, and communications equipment. A dual receiver supports two channels in one package, helping conserve board area in systems where connector density and card real estate are important. The 3.3 V CMOS supply aligns with common communications logic levels, and the greater-than-400-Mbps capability suits point-to-point backplanes or shielded cable links. Maintain controlled-impedance routing and confirm the source driver's timing, termination, and output voltage against the receiver requirements.

🖥️

Clock and Data Recovery Links

The DS90LV028ATMX is suitable for receiving a differential clock alongside a data channel in point-to-point digital systems. Operating above 200 MHz provides margin for communication links, while the two-channel arrangement can reduce package count in clock-and-data architectures. The receiver converts differential LVDS levels to CMOS-compatible outputs for downstream logic. Placement and trace matching are critical: route the clock and data pairs according to the source interface requirements, minimize connector transitions, and verify timing budget across transmitter, channel, receiver, and destination device.

💊

Medical and Instrumentation Signal Interfaces

The DS90LV028ATMX can serve as the digital interface between instrumentation or medical-control hardware and a remote low-noise sensor module using LVDS. Differential signaling reduces susceptibility to interference compared with single-ended links, and the receiver's low-noise architecture is appropriate for systems transporting precise digital control or measurement information. The device does not directly acquire analog sensor outputs; those signals require suitable front-end conversion before LVDS transmission. Confirm medical-system quality, regulatory, and qualification requirements separately from the device's electrical suitability.

Ringkasan Produk Disebarkan

DS90LV027A Compatible dual LVDS driver for the transmitting endpoint Dipergunakan di: High-Speed Board-to-Board LVDS Links, FPGA and Processor LVDS Interfaces, Telecommunications and Network Equipment, Clock and Data Recovery Links DS90LV028A Base family designation for receiver-based links Dipergunakan di: High-Speed Board-to-Board LVDS Links, FPGA and Processor LVDS Interfaces, Industrial Data Acquisition Equipment ADN4664BRZ Cross-brand LVDS receiver alternative for industrial links Dipergunakan di: Industrial Data Acquisition Equipment, Medical and Instrumentation Signal Interfaces STLVDS9637BD Cross-brand LVDS receiver option Dipergunakan di: Telecommunications and Network Equipment DS90LV028ATM Texas Instruments Dipergunakan di: Clock and Data Recovery Links DS90LV028ATMX/NOPB Same-family ordering option for interface designs Dipergunakan di: Medical and Instrumentation Signal Interfaces
What is the DS90LV028ATMX?
The DS90LV028ATMX is a Texas Instruments dual CMOS differential line receiver for Low Voltage Differential Signaling data links. According to the TI product page, it accepts approximately 350 mV differential inputs and supports rates above 400 Mbps, equivalent to 200 MHz. The device is packaged in an 8-pin SOIC and is intended for low-power, low-noise interface designs requiring two independent receive channels.
What is the operating voltage of DS90LV028ATMX?
The DS90LV028ATMX operates from a nominal 3.3 V supply. The device is specifically described as a 3 V LVDS dual CMOS differential line receiver, while a component listing identifies its supply voltage as 3.3 V. Before finalizing a power design, use the pin-description and electrical-characteristics tables in the manufacturer datasheet to confirm the precise recommended supply limits and operating conditions.
What data rate does DS90LV028ATMX support?
The DS90LV028ATMX supports data rates in excess of 400 Mbps, corresponding to a clock frequency above 200 MHz according to the TI product description. This performance is suitable for balanced point-to-point links carrying high-speed digital data. The actual usable rate depends on cable length, connector performance, PCB impedance, source timing, receiver input thresholds, and the integrity of the differential pair.
Where can I download the DS90LV028ATMX datasheet PDF?
The official DS90LV028A datasheet and supporting technical documents can be accessed from the Texas Instruments product page at https://www.ti.com/product/DS90LV028A. Select the DS90LV028ATMX orderable option to access its specific documents. The manufacturer page is preferable to third-party copies because it contains current revisions, lifecycle information, and notices associated with the orderable part.
Where is the pinout for DS90LV028ATMX located?
The DS90LV028ATMX pin configuration is shown in the pin-configuration diagram and connection table in the DS90LV028A manufacturer datasheet. The package is an 8-pin SOIC. Use that table to identify supply, ground, differential inputs, and CMOS outputs before assigning PCB nets. Because the package drawing alone does not establish signal names, do not infer pin functions solely from pin position.
What are the key specifications of DS90LV028ATMX?
The DS90LV028ATMX is a dual CMOS LVDS receiver with a nominal 3.3 V supply, approximately 350 mV typical differential input, and operation above 400 Mbps or 200 MHz. It uses an 8-SOIC package and is specified for -40 C to +85 C operation. According to the TI product page, its design priorities are ultra-low power dissipation, low noise, and high data rate.
Is DS90LV028ATMX suitable for high-speed backplane communication?
The DS90LV028ATMX is suitable for LVDS links above 400 Mbps when the channel is implemented as a properly terminated differential pair with controlled PCB impedance. Its dual receiver arrangement is useful for two related channels on a communication card. Actual backplane reach is not a single device specification; it depends on trace geometry, connector losses, skew, source edge rate, noise margin, and the intended clocking scheme.
How should DS90LV028ATMX be used with an LVDS driver?
A typical link places a compatible dual LVDS driver at the transmitting endpoint and the DS90LV028ATMX at the receiving endpoint. The DS90LV027A is identified as a related 3 V dual high-speed differential driver. Confirm voltage levels, propagation delay, input thresholds, termination, and timing compatibility in both datasheets before closing the interface. The receiver then converts each differential input pair into CMOS-compatible logic levels.
What is the difference between DS90LV028ATMX and DS90LV028ATM/NOPB?
Both devices belong to the Texas Instruments DS90LV028A family and are listed as 8-SOIC dual CMOS LVDS receivers with the same nominal 3.3 V supply and greater-than-400-Mbps capability. Their documented orderable identifiers and packaging suffixes differ, so the exact ordering code, reel configuration, and any qualification distinctions must be checked before substitution. The manufacturer part-details page should control procurement and qualification decisions.
When should I choose DS90LV028ATMX over an LVDS transceiver?
Choose the DS90LV028ATMX when the board only needs to receive two differential LVDS signals and the opposite endpoint already provides compatible LVDS transmission. A transceiver adds driver circuitry, supply current, package size, and potential signal-chain complexity that may be unnecessary for a receive-only link. Use a transceiver instead when the design must both transmit and receive through the same interface.
What is the best drop-in replacement for DS90LV028ATMX?
The closest same-family drop-in choices are the documented DS90LV028A orderable variants using the same 8-SOIC format, including DS90LV028ATM/NOPB and DS90LV028ATM. Cross-reference listings also identify ADN4664BRZ and STLVDS9637BD as alternatives. No candidate should be installed solely from a family label: verify the 8-SOIC pin arrangement, supply limits, input threshold, propagation delay, and receiver enable behavior in its manufacturer datasheet.
What can replace DS90LV028ATMX?
DS90LV028ATMX can be replaced by a verified 8-SOIC dual LVDS receiver with compatible CMOS supply voltage, differential input threshold, propagation delay, and logic-output levels. Documented candidates include DS90LV028ATM/NOPB, DS90LV028ATM, ADN4664BRZ, and STLVDS9637BD. Treat the first three as family or ordering candidates and confirm timing and pin functions before using a cross-brand substitute in an existing layout.
Is DS90LV028ATMX the same as DS90LV028ATM/NOPB?
The DS90LV028ATMX and DS90LV028ATM/NOPB are presented as members of the same DS90LV028A dual CMOS differential receiver family in the same 8-SOIC package. Their documented core role, nominal 3.3 V supply, and high-speed LVDS receive function align. The orderable identifiers differ, so check the manufacturer ordering table for exact suffix, reel, temperature, and qualification details before treating them as identical.
Where can I buy DS90LV028ATMX and what is its price?
Current commercial terms for the DS90LV028ATMX can be requested through the Request a Quote form on this page. The form is the appropriate channel for checking unit pricing, quantity pricing, stock status, minimum order quantity, and lead time without inserting figures that may become stale. Provide the complete DS90LV028ATMX orderable code and the required production quantity when submitting the request.
What is the lead time and stock status for DS90LV028ATMX?
The current lead time and stock status for DS90LV028ATMX should be confirmed through the Request a Quote form on this page. Request the exact MPN, reel quantity, and required delivery date. For production planning, also obtain the manufacturer lifecycle and ordering information so that supply commitments correspond to the specific DS90LV028ATMX variant rather than a related family member.
What are the compliance qualifications of DS90LV028ATMX?
The DS90LV028ATMX compliance declarations should be taken from the current manufacturer product page and the declarations associated with the exact orderable MPN. The interface is a 3 V CMOS device in an 8-SOIC package, but attributes such as RoHS, REACH, lead-free, halogen-free, and automotive qualification cannot be inferred from the package or operating temperature alone. Request current compliance documentation during procurement review.

Data referensi kejuruteraan untuk DS90LV028ATMX — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the DS90LV028ATMX for a receive-only LVDS link requiring two channels, approximately 350 mV differential input, and operation above 400 Mbps on a 3.3 V CMOS system. A same-family orderable variant such as DS90LV028ATM/NOPB is the first choice when procurement requires another exact TI suffix, provided its manufacturer ordering details match the design. ADN4664BRZ or STLVDS9637BD may fit the same 8-SOIC footprint, but select them only after comparing input thresholds, propagation delay, supply range, output behavior, and enable or fail-safe functions against the original design. Use a transceiver instead of a standalone receiver when the board must transmit and receive. The DS90LV028ATMX is best for compact, high-speed digital interfaces where low power, low noise, and direct LVDS-to-CMOS conversion are priorities.

Perbandingan dengan Gantian

Parametr Produk Ini DS90LV028ATM/NOPB DS90LV028ATM DS90LV028ATMXN ADN4664BRZ STLVDS9637BD
Package 8-SOIC 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same
Brand Texas Instruments Texas Instruments Texas Instruments National Semiconductor Analog Devices STMicroelectronics

Penyeberangsung Jelas

  • Two high-speed LVDS receive channels in one package (vsDS90LV028ATM/NOPB)
  • Directly documented manufacturer-family alignment (vsADN4664BRZ)
  • Low-power differential receive function with CMOS outputs (vsSTLVDS9637BD)

Catatan Desain

Route each LVDS input as a tightly coupled differential pair with symmetric geometry and uninterrupted reference planes. Avoid adding test pads, vias, or component branches unless they are incorporated into the source and receiver impedance models. Keep the route from the external connector to the DS90LV028ATMX as short as practical, because connector transitions and long unmatched traces can increase reflections and reduce timing margin at rates above 200 MHz.

Verify the complete link rather than only the receiver. Confirm the transmitter's differential output voltage, input threshold, propagation delay, termination scheme, and timing against the DS90LV028ATMX specifications. Use the manufacturer receiver test setup and PCB guidance as the basis for controlled-impedance values. Also check differential and common-mode voltage limits so that cable noise or ground-bounce effects do not move the signal outside the valid input range.

Place the required supply bypass capacitor immediately between the device supply and ground pins, with a short via connection to the ground plane. Keep the capacitor footprint and traces compact to suppress switching and ground-bounce noise. Provide clean 3.3 V power from the system rail and avoid sharing long supply traces with high-current loads. Confirm actual supply-current limits and decoupling requirements in the manufacturer electrical-characteristics table.

Do not substitute a receiver solely because it is labeled dual, LVDS, or 8-SOIC. Before using ADN4664BRZ or STLVDS9637BD, compare pin functions, differential input threshold, propagation delay, supply range, output polarity, and any enable or fail-safe pins. For same-family replacements, confirm whether the suffix changes reel form, temperature grade, qualification, or ordering terms. A successful footprint fit alone does not guarantee timing-compatible interchangeability.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

Compliance declarations for the exact DS90LV028ATMX orderable code require confirmation from the current manufacturer product documentation. AEC-Q100 status is unknown because automotive qualification was not stated.

Data disahkan pada: 2026-11-10 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

ds90lv028atmx nopb DS90LV028ATMX datasheet DS90LV028ATMX datasheet pdf DS90LV028ATMX pinout DS90LV028ATMX equivalent DS90LV028ATMX replacement DS90LV028ATMX cross reference DS90LV028ATMX footprint DS90LV028ATMX application circuit Texas Instruments DS90LV028ATMX DS90LV028ATMX price DS90LV028ATMX stock DS90LV028ATMX vs DS90LV028ATM DS90LV028A 8-SOIC pinout

Komponen dan Tanda berkaitan

Texas Instruments DS90LV028ATMX DS90LV028A DS90LV027A DS90LV028ATM/NOPB DS90LV028ATM DS90LV028ATMXN ADN4664BRZ STLVDS9637BD LVDS Low Voltage Differential Signaling differential line receiver line receiver interface IC CMOS dual receiver high-speed serial interface 8-SOIC SOIC package family surface-mount package differential input common-mode rejection power management point-to-point link 400 Mbps data rate
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ