DS90LV028ATMX - Dual LVDS Receiver | Texas Instruments
部品番号: DS90LV028ATMX ✓ 生産中DS90LV028ATMX 概要
An LVDS receiver is an interface IC that recovers a digital signal from two complementary low-voltage differential conductors. LVDS, or Low Voltage Differential Signaling, reduces signal amplitude and common-mode interference compared with single-ended signaling. This dual receiver belongs to the broader line-receiver and interface-IC hierarchy used to connect high-speed digital sources to CMOS processors, FPGAs, transceivers, and communications equipment.
The DS90LV028A family emphasizes low power dissipation, low noise, and high data rates. Its dual-channel architecture can receive two independent differential signals in one package. A nominal 3.3 V supply supports integration with 3 V CMOS systems, while the 350 mV typical differential input aligns with standard LVDS signaling. The 8-SOIC package provides a compact surface-mount footprint suitable for communication cards and embedded control systems.
Internally, the receiver converts small differential voltages into stable CMOS logic levels. Differential reception rejects noise that appears equally on both input conductors, improving signal integrity in cable, backplane, and point-to-point environments. The two-channel organization allows one receiver package to support paired data paths, reducing component count compared with separate single-channel receivers when board area is constrained.
Typical uses include receipt of high-speed LVDS links between boards, recovery of differential clock or data signals, and interfacing LVDS links to CMOS processors, FPGAs, and communications controllers. The device can also be paired with a compatible dual LVDS driver, such as the DS90LV027A, in systems that transmit and receive differential data over a balanced connection.
When laying out the receiver, route the differential pair as a tightly coupled pair, minimize stub branches, and use controlled-impedance PCB geometry. Keep the receiver close to the connector or source when practical, because added trace length and mismatched routing can reduce signal margin. Decoupling capacitors should be placed close to the supply and ground pins to limit transient supply noise.
This page combines the manufacturer device description, interface characteristics, cross-reference options, and practical PCB guidance into a compact engineering reference. The comparison table separates documented electrical ratings from unresolved parameters, helping designers evaluate replacement candidates without overlooking pin compatibility, supply voltage, or application-specific requirements.
ドロップイン代替品: DS90LV028ATMX — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DS90LV028ATMX (同一形状・フットプリント) — 相違点: Device Type, Package, Signaling Standard, Supply Voltage.
DS90LV028ATM/NOPB
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DS90LV028ATM
✅ ドロップイン価格はお問い合わせください
データシートを見る →DS90LV028ATMXN
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ADN4664BRZ
✅ ドロップイン📋 参考代替品(カタログ未掲載)
STLVDS9637BD
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DS90LV028ATMX 仕様
| Device Type | Dual CMOS differential line receiver |
| Channel Count | 2 channels |
| Logic Technology | CMOS |
| 電源電圧 | 3.3 V |
| Minimum Data Rate | Greater than 400 Mbps |
| 最大クロック周波数 | 200 MHz |
| Differential Input Signal | 350 mV typical |
| 動作温度 | -40 C to +85 C |
| パッケージ | 8-SOIC |
| ピン数 | 8 pins |
| 実装タイプ | Surface mount |
DS90LV028ATMX 8-soic ピン配置ガイド
DS90LV028ATMX (8-soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: DS90LV028ATMX.
詳細は データシート をご参照ください。
主な用途
DS90LV028ATMX の用途: 6 件s: High-Speed Board-to-Board LVDS Links, FPGA and Processor LVDS Interfaces, Industrial Data Acquisition Equipment, Telecommunications and Network Equipment, Clock and Data Recovery Links, Medical and Instrumentation Signal Interfaces.
High-Speed Board-to-Board LVDS Links
The DS90LV028ATMX fits receive points on compact board-to-board links because it recovers two LVDS signals while operating above 400 Mbps and accepting approximately 350 mV differential input. Place the device near the connector or source termination to minimize trace loss and preserve timing margin. The two channels support paired communication paths in one 8-SOIC package, reducing component count while maintaining a standard 3.3 V CMOS supply. PCB routing should use a coupled differential pair, controlled impedance, and no unterminated stubs.
おすすめ
FPGA and Processor LVDS Interfaces
The DS90LV028ATMX is useful when an FPGA or processor lacks native LVDS input but requires high-speed differential reception. Its greater-than-400-Mbps capability, corresponding to operation above 200 MHz, supports clock and data paths, while the dual receiver architecture can recover two related channels. The CMOS output interface operates from a nominal 3.3 V supply, simplifying integration with compatible digital logic. Validate output timing, input thresholds, and system skew against the FPGA or processor specifications before finalizing the interface.
おすすめ
Industrial Data Acquisition Equipment
Industrial measurement and acquisition equipment can use the DS90LV028ATMX to receive low-amplitude differential signals arriving from remote sensors, converters, or test fixtures. Differential reception helps reject common-mode noise encountered in industrial environments, while the device's low-power, low-noise design supports compact multi-channel instruments. Its -40 C to +85 C specified operating range covers many industrial ambient conditions. Design the analog front end and cable return path so differential amplitude and common-mode limits remain within the receiver's electrical requirements.
おすすめ
Telecommunications and Network Equipment
The DS90LV028ATMX can terminate high-speed LVDS connections inside line cards, interface modules, and communications equipment. A dual receiver supports two channels in one package, helping conserve board area in systems where connector density and card real estate are important. The 3.3 V CMOS supply aligns with common communications logic levels, and the greater-than-400-Mbps capability suits point-to-point backplanes or shielded cable links. Maintain controlled-impedance routing and confirm the source driver's timing, termination, and output voltage against the receiver requirements.
おすすめ
Clock and Data Recovery Links
The DS90LV028ATMX is suitable for receiving a differential clock alongside a data channel in point-to-point digital systems. Operating above 200 MHz provides margin for communication links, while the two-channel arrangement can reduce package count in clock-and-data architectures. The receiver converts differential LVDS levels to CMOS-compatible outputs for downstream logic. Placement and trace matching are critical: route the clock and data pairs according to the source interface requirements, minimize connector transitions, and verify timing budget across transmitter, channel, receiver, and destination device.
おすすめ
Medical and Instrumentation Signal Interfaces
The DS90LV028ATMX can serve as the digital interface between instrumentation or medical-control hardware and a remote low-noise sensor module using LVDS. Differential signaling reduces susceptibility to interference compared with single-ended links, and the receiver's low-noise architecture is appropriate for systems transporting precise digital control or measurement information. The device does not directly acquire analog sensor outputs; those signals require suitable front-end conversion before LVDS transmission. Confirm medical-system quality, regulatory, and qualification requirements separately from the device's electrical suitability.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DS90LV028ATMX — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DS90LV028ATM/NOPB | DS90LV028ATM | DS90LV028ATMXN | ADN4664BRZ | STLVDS9637BD |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | National Semiconductor | Analog Devices | STMicroelectronics |
主な差別化要因
- Two high-speed LVDS receive channels in one package (vs DS90LV028ATM/NOPB)
- Directly documented manufacturer-family alignment (vs ADN4664BRZ)
- Low-power differential receive function with CMOS outputs (vs STLVDS9637BD)
設計ノート
Route each LVDS input as a tightly coupled differential pair with symmetric geometry and uninterrupted reference planes. Avoid adding test pads, vias, or component branches unless they are incorporated into the source and receiver impedance models. Keep the route from the external connector to the DS90LV028ATMX as short as practical, because connector transitions and long unmatched traces can increase reflections and reduce timing margin at rates above 200 MHz.
Verify the complete link rather than only the receiver. Confirm the transmitter's differential output voltage, input threshold, propagation delay, termination scheme, and timing against the DS90LV028ATMX specifications. Use the manufacturer receiver test setup and PCB guidance as the basis for controlled-impedance values. Also check differential and common-mode voltage limits so that cable noise or ground-bounce effects do not move the signal outside the valid input range.
Place the required supply bypass capacitor immediately between the device supply and ground pins, with a short via connection to the ground plane. Keep the capacitor footprint and traces compact to suppress switching and ground-bounce noise. Provide clean 3.3 V power from the system rail and avoid sharing long supply traces with high-current loads. Confirm actual supply-current limits and decoupling requirements in the manufacturer electrical-characteristics table.
Do not substitute a receiver solely because it is labeled dual, LVDS, or 8-SOIC. Before using ADN4664BRZ or STLVDS9637BD, compare pin functions, differential input threshold, propagation delay, supply range, output polarity, and any enable or fail-safe pins. For same-family replacements, confirm whether the suffix changes reel form, temperature grade, qualification, or ordering terms. A successful footprint fit alone does not guarantee timing-compatible interchangeability.
コンプライアンス情報
Compliance declarations for the exact DS90LV028ATMX orderable code require confirmation from the current manufacturer product documentation. AEC-Q100 status is unknown because automotive qualification was not stated.