DS90LV028ATMX - Dual LVDS Receiver | Texas Instruments
MPN: DS90LV028ATMX ✓ 啟用中DS90LV028ATMX 概覽
An LVDS receiver is an interface IC that recovers a digital signal from two complementary low-voltage differential conductors. LVDS, or Low Voltage Differential Signaling, reduces signal amplitude and common-mode interference compared with single-ended signaling. This dual receiver belongs to the broader line-receiver and interface-IC hierarchy used to connect high-speed digital sources to CMOS processors, FPGAs, transceivers, and communications equipment.
The DS90LV028A family emphasizes low power dissipation, low noise, and high data rates. Its dual-channel architecture can receive two independent differential signals in one package. A nominal 3.3 V supply supports integration with 3 V CMOS systems, while the 350 mV typical differential input aligns with standard LVDS signaling. The 8-SOIC package provides a compact surface-mount footprint suitable for communication cards and embedded control systems.
Internally, the receiver converts small differential voltages into stable CMOS logic levels. Differential reception rejects noise that appears equally on both input conductors, improving signal integrity in cable, backplane, and point-to-point environments. The two-channel organization allows one receiver package to support paired data paths, reducing component count compared with separate single-channel receivers when board area is constrained.
Typical uses include receipt of high-speed LVDS links between boards, recovery of differential clock or data signals, and interfacing LVDS links to CMOS processors, FPGAs, and communications controllers. The device can also be paired with a compatible dual LVDS driver, such as the DS90LV027A, in systems that transmit and receive differential data over a balanced connection.
When laying out the receiver, route the differential pair as a tightly coupled pair, minimize stub branches, and use controlled-impedance PCB geometry. Keep the receiver close to the connector or source when practical, because added trace length and mismatched routing can reduce signal margin. Decoupling capacitors should be placed close to the supply and ground pins to limit transient supply noise.
This page combines the manufacturer device description, interface characteristics, cross-reference options, and practical PCB guidance into a compact engineering reference. The comparison table separates documented electrical ratings from unresolved parameters, helping designers evaluate replacement candidates without overlooking pin compatibility, supply voltage, or application-specific requirements.
直接替換替代品,適用於 DS90LV028ATMX — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: DS90LV028ATMX (相同外形與佔位) — 差異在於 Device Type, Package, Signaling Standard, Supply Voltage.
DS90LV028ATM/NOPB
✅ 直接替換📋 參考替代品(不在目錄中)
DS90LV028ATM
✅ 直接替換聯絡詢價
查看資料表 →DS90LV028ATMXN
✅ 直接替換📋 參考替代品(不在目錄中)
ADN4664BRZ
✅ 直接替換📋 參考替代品(不在目錄中)
STLVDS9637BD
✅ 直接替換📋 參考替代品(不在目錄中)
DS90LV028ATMX 規格
| Device Type | Dual CMOS differential line receiver |
| Channel Count | 2 channels |
| Logic Technology | CMOS |
| 供應電壓 | 3.3 V |
| Minimum Data Rate | Greater than 400 Mbps |
| 最大時脈頻率 | 200 MHz |
| Differential Input Signal | 350 mV typical |
| 工作溫度 | -40 C to +85 C |
| 封裝 | 8-SOIC |
| 腳位數 | 8 pins |
| 安裝類型 | Surface mount |
DS90LV028ATMX 8-soic 腳位配置指南
DS90LV028ATMX(8-soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: DS90LV028ATMX.
請參閱 資料表 以查看完整腳位配置。
典型應用
DS90LV028ATMX 適用於 6 應用s: High-Speed Board-to-Board LVDS Links, FPGA and Processor LVDS Interfaces, Industrial Data Acquisition Equipment, Telecommunications and Network Equipment, Clock and Data Recovery Links, Medical and Instrumentation Signal Interfaces.
High-Speed Board-to-Board LVDS Links
The DS90LV028ATMX fits receive points on compact board-to-board links because it recovers two LVDS signals while operating above 400 Mbps and accepting approximately 350 mV differential input. Place the device near the connector or source termination to minimize trace loss and preserve timing margin. The two channels support paired communication paths in one 8-SOIC package, reducing component count while maintaining a standard 3.3 V CMOS supply. PCB routing should use a coupled differential pair, controlled impedance, and no unterminated stubs.
推薦
FPGA and Processor LVDS Interfaces
The DS90LV028ATMX is useful when an FPGA or processor lacks native LVDS input but requires high-speed differential reception. Its greater-than-400-Mbps capability, corresponding to operation above 200 MHz, supports clock and data paths, while the dual receiver architecture can recover two related channels. The CMOS output interface operates from a nominal 3.3 V supply, simplifying integration with compatible digital logic. Validate output timing, input thresholds, and system skew against the FPGA or processor specifications before finalizing the interface.
推薦
Industrial Data Acquisition Equipment
Industrial measurement and acquisition equipment can use the DS90LV028ATMX to receive low-amplitude differential signals arriving from remote sensors, converters, or test fixtures. Differential reception helps reject common-mode noise encountered in industrial environments, while the device's low-power, low-noise design supports compact multi-channel instruments. Its -40 C to +85 C specified operating range covers many industrial ambient conditions. Design the analog front end and cable return path so differential amplitude and common-mode limits remain within the receiver's electrical requirements.
推薦
Telecommunications and Network Equipment
The DS90LV028ATMX can terminate high-speed LVDS connections inside line cards, interface modules, and communications equipment. A dual receiver supports two channels in one package, helping conserve board area in systems where connector density and card real estate are important. The 3.3 V CMOS supply aligns with common communications logic levels, and the greater-than-400-Mbps capability suits point-to-point backplanes or shielded cable links. Maintain controlled-impedance routing and confirm the source driver's timing, termination, and output voltage against the receiver requirements.
推薦
Clock and Data Recovery Links
The DS90LV028ATMX is suitable for receiving a differential clock alongside a data channel in point-to-point digital systems. Operating above 200 MHz provides margin for communication links, while the two-channel arrangement can reduce package count in clock-and-data architectures. The receiver converts differential LVDS levels to CMOS-compatible outputs for downstream logic. Placement and trace matching are critical: route the clock and data pairs according to the source interface requirements, minimize connector transitions, and verify timing budget across transmitter, channel, receiver, and destination device.
推薦
Medical and Instrumentation Signal Interfaces
The DS90LV028ATMX can serve as the digital interface between instrumentation or medical-control hardware and a remote low-noise sensor module using LVDS. Differential signaling reduces susceptibility to interference compared with single-ended links, and the receiver's low-noise architecture is appropriate for systems transporting precise digital control or measurement information. The device does not directly acquire analog sensor outputs; those signals require suitable front-end conversion before LVDS transmission. Confirm medical-system quality, regulatory, and qualification requirements separately from the device's electrical suitability.
推薦
推薦產品摘要
工程參考資料,適用於 DS90LV028ATMX — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | DS90LV028ATM/NOPB | DS90LV028ATM | DS90LV028ATMXN | ADN4664BRZ | STLVDS9637BD |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | National Semiconductor | Analog Devices | STMicroelectronics |
主要差異化特點
- Two high-speed LVDS receive channels in one package (對比DS90LV028ATM/NOPB)
- Directly documented manufacturer-family alignment (對比ADN4664BRZ)
- Low-power differential receive function with CMOS outputs (對比STLVDS9637BD)
設計說明
Route each LVDS input as a tightly coupled differential pair with symmetric geometry and uninterrupted reference planes. Avoid adding test pads, vias, or component branches unless they are incorporated into the source and receiver impedance models. Keep the route from the external connector to the DS90LV028ATMX as short as practical, because connector transitions and long unmatched traces can increase reflections and reduce timing margin at rates above 200 MHz.
Verify the complete link rather than only the receiver. Confirm the transmitter's differential output voltage, input threshold, propagation delay, termination scheme, and timing against the DS90LV028ATMX specifications. Use the manufacturer receiver test setup and PCB guidance as the basis for controlled-impedance values. Also check differential and common-mode voltage limits so that cable noise or ground-bounce effects do not move the signal outside the valid input range.
Place the required supply bypass capacitor immediately between the device supply and ground pins, with a short via connection to the ground plane. Keep the capacitor footprint and traces compact to suppress switching and ground-bounce noise. Provide clean 3.3 V power from the system rail and avoid sharing long supply traces with high-current loads. Confirm actual supply-current limits and decoupling requirements in the manufacturer electrical-characteristics table.
Do not substitute a receiver solely because it is labeled dual, LVDS, or 8-SOIC. Before using ADN4664BRZ or STLVDS9637BD, compare pin functions, differential input threshold, propagation delay, supply range, output polarity, and any enable or fail-safe pins. For same-family replacements, confirm whether the suffix changes reel form, temperature grade, qualification, or ordering terms. A successful footprint fit alone does not guarantee timing-compatible interchangeability.
合規資訊
Compliance declarations for the exact DS90LV028ATMX orderable code require confirmation from the current manufacturer product documentation. AEC-Q100 status is unknown because automotive qualification was not stated.