ISL84051IB - 8:1 100Ω Analog Multiplexer | Renesas
MPN: ISL84051IB ✓ AktifISL84051IB Ringkasan
An analog multiplexer is an interface IC that connects one of several input channels to a shared output path. It belongs to the broader analog switch and signal-routing hierarchy, which sits within interface semiconductors and embedded control systems. Multiplexers reduce the number of physical connections required by sensors, test equipment, data acquisition systems, and communication equipment while allowing one converter or processor input to monitor multiple signals.
The ISL84051IB's principal benefits include its 8:1 channel ratio, maximum on-resistance of 100 ohm at ±5 V, low-voltage operation, and pin compatibility with established multiplexers. The inhibit pin simplifies system control because all signal paths can be disconnected simultaneously. TTL and CMOS-compatible address and select inputs also support a broad range of digital control circuits without requiring elevated input levels.
Internally, the device uses controlled analog switches to route one selected input to the common output. Its on-resistance matching between channels keeps similar resistance characteristics across the selected paths, helping preserve signal amplitude consistency. Because it is a passive switch rather than an active amplifier, it introduces insertion loss determined principally by on-resistance and does not provide gain or level shifting.
Typical applications include battery-powered instrumentation, automated test equipment, data acquisition, communication routing, sample-and-hold systems, and microcontroller-based sensor interfaces. The low +2 V minimum supply is useful for portable equipment, while dual-supply operation is valuable when signals can be bipolar. The 16-pin SOIC package also supports conventional surface-mount assembly and board-level manual inspection.
Designers should verify signal amplitude, bandwidth, injection charge, off leakage, and the complete logic truth table against the manufacturer datasheet. Keep high-impedance routing paths short, provide a stable ground reference, and account for the resistance of PCB traces when precision measurements depend on total path resistance.
This page combines the manufacturer device description with a focused engineering comparison, replacement guidance, pin-level sourcing information, and practical application guidance for engineers evaluating the ISL84051IB in multiplexed analog signal paths.
Pilihan pengganti yang segera untuk ISL84051IB — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
ISL84051IBZ
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MAX4051
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MAX4051A
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MAX4581
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
74HC4051
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
ISL84051IB Spesifikasi
| Multiplexer Configuration | 8:1 |
| Number of Circuits | 1 circuit |
| On-Resistance | 100 ohm maximum at ±5 V |
| Single-Supply Voltage Range | +2 V to +12 V |
| Dual-Supply Operation | Supported |
| Control Input Compatibility | TTL and CMOS |
| Inhibit Function | Simultaneously opens all signal paths |
| Kemasan | 16-pin SOIC |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin ISL84051IB 16-pin soic
Konfigurasi pin untuk ISL84051IB (16-pin soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk ISL84051IB.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
ISL84051IB patut untuk 6 aplikasis: Battery-Powered Sensor Multiplexing, Automated Test Equipment, Data Acquisition Systems, Communication Signal Routing, Sample-and-Hold Systems, Programmable Instrument Control.
Battery-Powered Sensor Multiplexing
The ISL84051IB fits portable sensor systems that need to monitor multiple inputs without allocating a separate converter channel to each sensor. Its +2 V to +12 V single-supply range accommodates low-energy rails, while the 8:1 configuration reduces external routing requirements. TTL and CMOS-compatible control inputs allow a microcontroller to select channels directly. The manufacturer specifies a maximum on-resistance of 100 ohm at ±5 V, which should be included in the sensor-loading calculation for high-impedance sources. The inhibit function can disconnect all paths during idle periods or measurement resets.
Disebarkan
Automated Test Equipment
The ISL84051IB can route one of eight test points to a shared measurement front end in automated test equipment. Its 100 ohm maximum on-resistance at ±5 V provides a defined basis for insertion-loss budgeting, and the common inhibit input supports safe isolation between measurement phases. The 16-pin SOIC package simplifies assembly on test fixture and instrument control boards. Engineers should verify bandwidth, switching time, leakage, and charge injection against the signal amplitude and source impedance, especially for sub-nanovolt or high-gain measurements.
Disebarkan
Data Acquisition Systems
The ISL84051IB is suitable for multiplexing resistive, voltage, and low-level sensor inputs into a shared data-acquisition channel. Its 8:1 organization reduces converter inputs, while the inhibit pin can provide deliberate isolation during channel settling or calibration. With a maximum on-resistance of 100 ohm at ±5 V, total path resistance must be added to the sensor's effective output impedance for accuracy analysis. The low-voltage single-supply capability also helps reduce the complexity of portable acquisition systems. Keep routed traces short, provide solid grounding, and account for PCB leakage at the required measurement bandwidth.
Disebarkan
Communication Signal Routing
The ISL84051IB can select among eight communication-related paths when a board must route one source to a shared receiver, monitoring point, or test port. Its TTL and CMOS-compatible selection inputs simplify interfacing with common digital controllers, and the simultaneous inhibit function helps prevent unintended signal propagation. The device does not amplify or level-shift signals, so insertion loss and off-channel behavior remain important. For high-frequency links, verify the specified bandwidth, on-resistance flatness, capacitance, and switching speed before using it near the data-rate limit.
Disebarkan
Sample-and-Hold Systems
The ISL84051IB can select one of eight sampled inputs for a sample-and-hold or comparator front end when the source count exceeds the available analog inputs. The 8:1 organization concentrates switching in one package, while the inhibit input allows all paths to open during acquisition or reset intervals. The 100 ohm maximum on-resistance at ±5 V adds to the charging resistance presented to the selected source, affecting acquisition time. Confirm charge injection, switch capacitance, leakage, and off isolation from the manufacturer datasheet before using the multiplexer in precision settling-sensitive circuits.
Disebarkan
Programmable Instrument Control
The ISL84051IB fits programmable instrument and interface boards that must connect one of eight external or internal nodes to a common control or measurement circuit. Its low-voltage operation allows the multiplexer to share a compact digital control domain, while TTL and CMOS-compatible inputs broaden controller compatibility. The inhibit function can support deterministic isolation during calibration or relay transition periods. Because the SOIC package exposes sensitive analog pins, use a quiet ground plane, minimize long traces, and place protection components where they will not materially degrade switch capacitance or leakage.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk ISL84051IB — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | ISL84051IBZ | MAX4051 | MAX4051A | MAX4581 | 74HC4051 |
|---|---|---|---|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Brand | Renesas Electronics | Renesas Electronics | Maxim Integrated | Maxim Integrated | Maxim Integrated | Texas Instruments |
| Multiplexer Configuration | 8:1 | 8:1 | 8:1 | 8:1 | 8:1 | 8:1 |
| Number of Pins | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins |
Penyeberangsung Jelas
- Low-voltage 8:1 multiplexing in the same 16-pin footprint (vs74HC4051)
- Documented drop-in relationship with an established Maxim family (vsMAX4051)
- Common inhibit control for simultaneous path isolation (vsMAX4581)
Catatan Desain
Include the 100 ohm maximum switch on-resistance in the complete source-impedance calculation at ±5 V. Add connector resistance, protection-device resistance, and PCB trace resistance to determine the actual attenuation seen by the downstream receiver. For high-impedance sensors, use short traces, a low-leakage protection network, and a grounded guard where practical. These precautions are especially important because a passive multiplexer cannot correct amplitude errors introduced by its finite path resistance.
Place the ISL84051IB close to the common analog output and the routed signal sources. Keep channel traces short, avoid sharing sensitive paths with high-current return currents, and provide a continuous ground reference beneath the analog section. The inhibit and address traces should be routed away from sensitive switching nodes where practical. Confirm that exposed SOIC leads have adequate solder-joint fillet formation and that copper thermal and current paths match the assembly process.
Do not select a replacement solely because it is labeled an 8:1 multiplexer. Verify the complete 16-pin map, select logic, inhibit polarity, supply range, control thresholds, on-resistance, leakage, bandwidth, and switching timing. The ISL84051 family datasheet documents compatibility with MAX4051, MAX4051A, MAX4581, and 74HC4051, but existing boards may also contain peripheral circuitry that assumes the original device's inactive-state behavior. Preserve the selected channel only after the system-level truth table is checked.
Maklumat Kesediaan
The manufacturer device description and the listed distributor pages do not provide a complete component-level compliance declaration for this ordering code. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status with the manufacturer before release.