DG408DYZ - 8:1 CMOS Analog Multiplexer | Renesas Electronics
MPN: DG408DYZ ✓ AktifDG408DYZ Ringkasan
An analog multiplexer is a switch matrix that routes one of several signal sources onto a shared output path. The DG408 belongs to the analog switch and multiplexer hierarchy, where its CMOS construction supports low power consumption and wide input voltage range compared with relay-based selectors. Its 8:1 configuration gives an eight-channel instrument, data-acquisition system, or automated test fixture a compact way to share one analog front end among multiple sources.
The device uses three address lines for binary channel selection and an active-low or active-high ENABLE control according to the manufacturer logic specification. A TTL/CMOS-compatible decoder accepts standard logic levels, while the internal voltage reference establishes stable switching thresholds across supply conditions. Because the analog paths are bidirectional, the same DG408DYZ can be used to route a common signal toward one of eight external terminals as well as to select an incoming source.
The DG408 series is documented as a drop-in replacement for the popular DG508A and DG509A families. Renesas also positions the DG408 and DG409 as pin-compatible single-ended 8-channel and differential 4-channel options respectively. The industrial DG408DYZ grade is suited to test and measurement, data acquisition, signal routing, control systems, and industrial interface boards where a SOIC footprint and deterministic logic decoding are preferred.
Bidirectional operation simplifies PCB routing because the channel pins are not restricted to a dedicated input or output role. Nevertheless, keep all external analog nodes within the absolute maximum ratings listed in the manufacturer datasheet, and use input protection networks when signals can exceed the selected supply rails. Account for the 100 ohm maximum on-resistance when calculating source impedance, especially when driving high-impedance sensors or precision measurement chains.
This page combines the manufacturer family information with distributor specifications, package details, equivalent-device references, and practical design guidance. It also identifies where a drop-in comparison should focus on package geometry, logic decoding, channel count, on-resistance, signal range, and temperature grade rather than on the DG408 name alone.
Pilihan pengganti yang segera untuk DG408DYZ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera DG408DYZ (sama faktor bentuk dan kaki) — berbeza dalam Package, On-Resistance, Channel Matching, Multiplexer Configuration, Switch Architecture.
DG408DY+
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →DG408DY+
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →DG408DY+
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →DG408DY+
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →TSX-310
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
DG408DYZ Spesifikasi
| Multiplexer Configuration | Single 8:1 |
| Number of Circuits | 1 circuit |
| Number of Channels | 8 channels |
| On-Resistance | 100 ohm maximum |
| Analog Signal Direction | Bidirectional |
| Switch Architecture | Eight analog switches with TTL/CMOS-compatible digital decode |
| Process Technology | CMOS |
| Logic Threshold Reference | Internal voltage reference |
| Device Selection Control | ENABLE input |
| Kemasan | 16-pin SOIC |
| Jenis Pemasangan | Surface mount |
| Gambaran Suhu Operasi | -40 C to +85 C |
| Industrial Grade | Yes |
| Legacy Compatibility | Drop-in replacement for DG508A and DG509A series devices |
Panduan Konfigurasi Pin DG408DYZ 16-pin soic
Konfigurasi pin untuk DG408DYZ (16-pin soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk DG408DYZ.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
DG408DYZ patut untuk 6 aplikasis: Multichannel Data Acquisition, Automated Test Equipment Signal Routing, Industrial Sensor Interface, Programmable Signal Conditioning, Battery-Powered Monitoring Equipment, Communication and RF Signal Routing.
Multichannel Data Acquisition
The DG408DYZ fits a data-acquisition front end that selects among eight analog sources with one shared amplifier chain. Its bidirectional analog paths allow either source selection or common-signal distribution, while the TTL/CMOS-compatible decoder and ENABLE input can be driven directly by a microcontroller or FPGA. The published 100 ohm maximum on-resistance must be included in the source-impedance budget, especially when measuring high-impedance sensors. Use the manufacturer pin table to assign tracks and confirm the allowed signal range before routing external inputs.
Disebarkan
Automated Test Equipment Signal Routing
In automated test equipment, the DG408DYZ can route one of eight test points, excitation nodes, or instrument channels through a common fixture interface. The ENABLE input allows a controller to disable the mux during fixture transitions, while the binary decoder selects the active path. Because the analog channels are bidirectional, the same device can also distribute a reference or stimulus to one selected branch. Maintain consistent impedance across all eight routes so switching does not create measurement errors, and include protection ahead of externally accessible nodes.
Disebarkan
Industrial Sensor Interface
The DG408DYZ can consolidate eight analog sensor outputs onto a single controller input, reducing the number of separate front-end channels in industrial monitoring equipment. Its -40 C to +85 C industrial temperature range suits equipment exposed to variable ambient conditions, and the TTL/CMOS-compatible control inputs simplify interfacing with standard digital logic. The 100 ohm maximum on-resistance can become significant with high-impedance sensors, so place a low-input-impedance buffer after the mux when full-scale accuracy is required. Keep sensor returns and mux ground paths within the device's rated common-mode limits.
Disebarkan
Programmable Signal Conditioning
A programmable signal-conditioning system can use the DG408DYZ to route different amplifier, filter, or reference taps into a common processing chain. This approach makes the board flexible without requiring a separate connector for every source and allows software to configure the channel address through the digital decoder. Bidirectional operation supports feedback-style measurements as well as source selection. The mux's 100 ohm maximum on-resistance introduces channel-dependent loading unless all branches are matched, so characterize the complete network and place any precision amplifier immediately after the selected node.
Disebarkan
Battery-Powered Monitoring Equipment
Portable monitoring equipment can use the DG408DYZ to reduce the number of analog inputs handled by a low-power controller. The CMOS multiplexer is designed for low-power operation, and the ENABLE control lets firmware disable the device when no channel needs to be observed. The shared-output topology also reduces board area compared with eight separate signal paths. Verify supply-current behavior and analog signal limits in the manufacturer datasheet for the intended battery voltage, and use a buffered output when the source impedance approaches the mux's 100 ohm maximum on-resistance.
Disebarkan
Communication and RF Signal Routing
The DG408DYZ can select low-level analog branches in communication equipment, instrumentation, or controlled test paths where a compact SOIC multiplexer is preferred. Bidirectional channels make it possible to route a common signal toward one of eight destinations as well as select a source for a receiver chain. The 100 ohm maximum on-resistance is modest for precision measurement but must be checked against the termination and noise requirements of the application. Keep sensitive traces away from digital address and ENABLE lines, and confirm the permitted signal swing in the manufacturer datasheet.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk DG408DYZ — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | DG408DY | DG408DY+ | DG408DY | DG408DY+ | TSX-310 |
|---|---|---|---|---|---|---|
| Manufacturer | Renesas Electronics | Renesas Electronics | Renesas Electronics | Vishay Intertechnology | Vishay Intertechnology | Texas Instruments |
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Multiplexer Configuration | Single 8:1 | Single 8:1 | Single 8:1 | 8-channel | 8-channel | 8:1 analog multiplexer |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Maximum On-Resistance | 100 ohm | 100 ohm | 100 ohm | 100 ohm class | 100 ohm class | Approximately 80 ohm |
| Analog Channel Direction | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional |
| Technology | CMOS | CMOS | CMOS | CMOS | CMOS | CMOS |
| Operating Temperature Range | -40 C to +85 C | Industrial grade | Industrial grade | Industrial grade | Industrial grade | -40 C to +85 C |
| Logic Compatibility | TTL/CMOS-compatible decode with ENABLE input | TTL/CMOS-compatible decode with ENABLE input | TTL/CMOS-compatible decode with ENABLE input | TTL/CMOS-compatible decode | TTL/CMOS-compatible decode | TTL/CMOS-compatible control |
| Legacy Replacement Target | DG508A and DG509A series | DG508A/DG509A family | DG508A/DG509A family | High-performance CMOS mux family | High-performance CMOS mux family | 8-channel analog multiplexer |
Penyeberangsung Jelas
- Single-ended 8-channel multiplexing with bidirectional analog paths (vsTSX-310)
- Documented compatibility with established DG508A and DG509A designs (vsTSX-310)
- Internal threshold reference and ENABLE control in the same 16-pin SOIC (vsMAX4634)
Catatan Desain
Treat the mux on-resistance as part of the source impedance. At the 100 ohm maximum, attenuation and thermal noise become more significant when the selected branch drives a high-impedance amplifier. Place a low-input-impedance buffer after the mux when the sensor impedance is high, and keep channel routing geometry similar so switching does not create gain or phase discontinuities between channels.
Route the eight analog paths as compact, mutually separated traces and connect the multiplexer ground reference to the quiet analog ground region. Keep the address and ENABLE traces away from sensitive analog nets. Because the channels are bidirectional, provide input protection at external connectors and ensure every external node remains inside the absolute maximum ratings in the manufacturer datasheet.
Do not assume that every part labeled DG408 is interchangeable solely from its multiplex ratio. Check the 16-pin SOIC pin map, supply-voltage range, ENABLE polarity, address convention, analog signal range, and switching specifications. Also verify the exact orderable suffix and packing method, because tape-and-reel, tube, and temperature-grade order codes can describe different purchasing configurations of the same device family.
Maklumat Kesediaan
The industrial temperature grade is documented, but no specific RoHS, REACH, halogen-free, or conflict-minerals declaration was identified in the available manufacturer and distributor records.