LM258DG4 - Dual 700 kHz Op Amp | Texas Instruments
MPN: LM258DG4 ✓ AktifLM258DG4 Ringkasan
An operational amplifier is a high-gain analog signal-processing IC used to amplify, buffer, compare, and filter signals. Within the power-management semiconductor hierarchy, the LM258 belongs to the general-purpose operational-amplifier family rather than precision, low-noise, or high-speed amplifier families. Its internally compensated design allows stable operation without external compensation components, while its differential input stage supports a broad range of general-purpose signal conditioning tasks.
Key features include a typical supply-current drain of 0.7 mA per amplifier, a typical input offset voltage of 3 mV, a typical input offset current of 2 nA, and a typical input bias current of 20 nA. The common-mode input range includes ground, which makes the LM258 useful for sensing signals close to the lower supply rail. The device can also operate with split supplies from approximately ±1.5 V to ±16 V.
The internally frequency-compensated architecture is intended for stable closed-loop gain configurations commonly used in voltage followers, transimpedance stages, comparators, and basic active filters. With a 700 kHz gain-bandwidth product and 0.3 V/us slew rate, the amplifiers prioritize low power consumption and wide supply-voltage tolerance rather than high-speed signal processing. Independent channel operation also allows one amplifier in the package to perform a different function from the other.
Typical applications include sensor-interface conditioning, battery-powered instrumentation, industrial control inputs, audio preamplifier stages, and DC motor-control feedback networks. Its ground-referenced common-mode capability is particularly useful when a sensor output lies near 0 V and the circuit has only one positive supply rail. The broad operating supply range also supports legacy industrial equipment operating from 5 V, 12 V, 15 V, or higher rails.
When using the LM258DG4, check the output-voltage swing, input common-mode limits, load current, and operating temperature against the application requirements. Place input and output decoupling capacitors close to the device pins, route sensitive input signals away from high-current switching paths, and account for input offset voltage when the measured signal is small. The manufacturer datasheet pin-description table should be used for final PCB and polarity verification.
This page combines the core electrical characteristics, practical application guidance, package information, and clearly qualified drop-in alternatives for LM258DG4. It is intended to accelerate component selection while keeping the final design decisions tied to the Texas Instruments datasheet and application-specific operating limits.
Pilihan pengganti yang segera untuk LM258DG4 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera LM258DG4 (sama faktor bentuk dan kaki) — berbeza dalam Package, Slew Rate, RoHS Status, Input Offset Voltage, Number of Channels.
LM258DR
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM258DR2G
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM258DRG4
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM2904DR
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM324DT
✅ Masuk Drop-In✓ Ada di Stok
$0.0827 / Unit
Lihat Datasheet →LM258DG4 Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | General Purpose |
| Number of Amplifiers | 2 circuits |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/us |
| Single-Supply Operating Voltage | 3 V to 32 V |
| Dual-Supply Operating Voltage | ±1.5 V to ±16 V |
| Quiescent Current per Amplifier | 0.7 mA typical |
| Input Offset Voltage | 3 mV typical |
| Input Offset Current | 2 nA typical |
| Input Bias Current | 20 nA typical |
| Common-Mode Input Range | Includes ground |
| Differential Input Voltage Range | ±32 V |
| Frequency Compensation | Internal |
| Kemasan | 8-SOIC, 0.154 inch body width |
| Package Width | 3.90 mm |
| Jenis Pemasangan | Surface Mount |
Konfigurasi Pin LM258DG4
| Pin 1 | OUT1 — Output of amplifier 1 |
| Pin 2 | IN1- — Inverting input of amplifier 1 |
| Pin 3 | IN1+ — Non-inverting input of amplifier 1 |
| Pin 4 | V- — Negative supply or ground connection |
| Pin 5 | IN2+ — Non-inverting input of amplifier 2 |
| Pin 6 | IN2- — Inverting input of amplifier 2 |
| Pin 7 | OUT2 — Output of amplifier 2 |
| Pin 8 | V+ — Positive supply connection |
Aplikasi Biasa
LM258DG4 patut untuk 6 aplikasis: Industrial Sensor Signal Conditioning, Single-Supply Audio Preamplifier, Battery-Powered Monitoring Equipment, DC Motor Feedback Control, Threshold and Window Detection, Active Filtering and Analog Control.
Industrial Sensor Signal Conditioning
The LM258DG4 fits low-frequency sensor interfaces where the sensed voltage can approach ground and the circuit uses a single positive supply. Its common-mode input range includes ground, while the 3 V to 32 V operating range supports multiple industrial rails. The 700 kHz gain-bandwidth product is appropriate for pressure, temperature, and position signals rather than high-frequency transducers. Designers should include the typical 3 mV input offset and 20 nA bias current when defining the accuracy budget, while the 0.3 V/us slew rate prevents abrupt large-signal settling.
Disebarkan
Single-Supply Audio Preamplifier
The LM258DG4 can provide voltage gain for low-level audio or control signals in a single-supply system. Its common-mode range includes ground, enabling biased input signals close to 0 V, and the internally compensated amplifier simplifies stable gain configuration. The 700 kHz gain-bandwidth product covers the audio band, while the 0.3 V/us slew rate is adequate for modest signal amplitudes. Headroom must remain between the input and output limits, and the 3 mV typical offset can create audible noise in very quiet stages unless gain and filtering are selected carefully.
Disebarkan
Battery-Powered Monitoring Equipment
The LM258DG4 is appropriate for portable monitoring equipment that prioritizes low supply-current consumption over high bandwidth. The LM258 family specifies a 0.7 mA typical supply-current drain per amplifier and can operate from a 3 V supply, allowing operation from regulated battery rails without a high-voltage supply requirement. The common-mode input range including ground supports sensors powered from the same rail. Because the amplifier is not rail-to-rail at every output condition, the usable signal range and output-swing limits must be checked against the battery voltage.
Disebarkan
DC Motor Feedback Control
The LM258DG4 can amplify a motor-position or current-feedback signal within a control loop while operating from an industrial voltage rail. Its 700 kHz gain-bandwidth product and 0.3 V/us slew rate support common feedback-control bandwidths, and the 3 V to 32 V supply range accommodates legacy 12 V and 24 V systems. Internal frequency compensation supports straightforward closed-loop implementation. Loop stability, output saturation recovery, and common-mode limits should be verified with the motor driver and worst-case supply tolerances because electrical offsets can influence steady-state control error.
Disebarkan
Threshold and Window Detection
The LM258DG4 is commonly used as an open-loop comparator for threshold, level, or window detection because it can accept inputs whose common-mode range includes ground. With a 3 V to 32 V single-supply range, it suits low-voltage logic-level sensing as well as higher-voltage industrial signals. The 3 mV typical input offset and 20 nA typical bias current determine threshold accuracy and input loading. A reference voltage must remain inside the allowable common-mode range, and output pull-up or pull-down arrangements may be required for the intended logic interface.
Disebarkan
Active Filtering and Analog Control
The LM258DG4 can implement active filters and proportional analog-control paths when the signal bandwidth is well below its 700 kHz gain-bandwidth product. Its dual channels can form a two-stage amplifier, active filter, or cascaded controller while consuming approximately 0.7 mA per amplifier typically. Internally compensated operation simplifies many voltage-feedback designs, although filter component tolerances and amplifier offset still influence cutoff frequency and DC accuracy. Avoid operating the outputs near the supply rails, and check the common-mode range before including the device in a precision filter.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LM258DG4 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | LM258DR | LM258DR2G | LM258DRG4 | LM2904 | LM324 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics | STMicroelectronics |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
| Maximum Single-Supply Voltage | 32 V | 32 V | 32 V | 32 V | 36 V | 30 V |
Penyeberangsung Jelas
- Matches the 700 kHz bandwidth of the closest LM258 ordering variants (vsLM258DR)
- Lower listed supply-voltage ceiling than the LM2904 option (vsLM2904)
- Lower bandwidth can simplify familiarity with legacy LM258 loop compensation (vsLM324)
Catatan Desain
Calculate the worst-case supply dissipation from the actual output voltage, load current, and quiescent current. For a single 5 V supply at a 2.5 V output and 10 mA load, the estimated load dissipation is (5 V - 2.5 V) × 0.01 A = 25 mW, while each amplifier adds approximately 0.7 mA of quiescent current. These estimates use VIN = 5 V, VOUT = 2.5 V, IOUT = 10 mA, and IQ = 0.7 mA per amplifier. Include regulator tolerances, output-load transients, and adjacent heat sources in the final thermal margin.
Place the decoupling capacitor from the positive supply pin to ground as close as practical to the SOIC, and keep the ground connection short and low-impedance. Route the two inverting inputs directly to their feedback resistors or sensing source to minimize parasitic capacitance and susceptibility to interference. For the common-mode input range that includes ground, maintain a clean ground reference under the package because input offset and bias-current errors are strongly influenced by ground-potential differences.
Do not assume that an input or output can swing exactly to 0 V or the positive supply rail. Although the common-mode input range includes ground, output swing and input range boundaries depend on supply voltage, load, output configuration, and device grade. Check the output-voltage swing curves and electrical limits for the highest signal and lowest supply condition. Also avoid using input or output pins as power rails, and verify that adjacent package pins are not left inconsistent with the selected single- or dual-supply topology.
Maklumat Kesediaan
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not explicitly identified in the cited listings. AEC-Q100 qualification is not indicated for this general-purpose amplifier ordering code.