Texas Instruments

LM258DG4 - Dual 700 kHz Op Amp | Texas Instruments

N.º de pieza: LM258DG4 ✓ Activo
3 V to 32 V Vdss 0.7 mA typical Id 8-SOIC, 0.154 inch body width Package Internal Speed
MOQ: 1 |

LM258DG4 Descripción general

The Texas Instruments LM258DG4 is a dual general-purpose operational amplifier with a gain-bandwidth product of 700 kHz, a slew rate of 0.3 V/us, and operation from a single 3 V to 32 V supply in an 8-pin SOIC package. The device contains two amplifiers and is suited to industrial and consumer circuits that need low supply current, single-supply operation, and an input common-mode range that includes ground.

An operational amplifier is a high-gain analog signal-processing IC used to amplify, buffer, compare, and filter signals. Within the power-management semiconductor hierarchy, the LM258 belongs to the general-purpose operational-amplifier family rather than precision, low-noise, or high-speed amplifier families. Its internally compensated design allows stable operation without external compensation components, while its differential input stage supports a broad range of general-purpose signal conditioning tasks.

Key features include a typical supply-current drain of 0.7 mA per amplifier, a typical input offset voltage of 3 mV, a typical input offset current of 2 nA, and a typical input bias current of 20 nA. The common-mode input range includes ground, which makes the LM258 useful for sensing signals close to the lower supply rail. The device can also operate with split supplies from approximately ±1.5 V to ±16 V.

The internally frequency-compensated architecture is intended for stable closed-loop gain configurations commonly used in voltage followers, transimpedance stages, comparators, and basic active filters. With a 700 kHz gain-bandwidth product and 0.3 V/us slew rate, the amplifiers prioritize low power consumption and wide supply-voltage tolerance rather than high-speed signal processing. Independent channel operation also allows one amplifier in the package to perform a different function from the other.

Typical applications include sensor-interface conditioning, battery-powered instrumentation, industrial control inputs, audio preamplifier stages, and DC motor-control feedback networks. Its ground-referenced common-mode capability is particularly useful when a sensor output lies near 0 V and the circuit has only one positive supply rail. The broad operating supply range also supports legacy industrial equipment operating from 5 V, 12 V, 15 V, or higher rails.

When using the LM258DG4, check the output-voltage swing, input common-mode limits, load current, and operating temperature against the application requirements. Place input and output decoupling capacitors close to the device pins, route sensitive input signals away from high-current switching paths, and account for input offset voltage when the measured signal is small. The manufacturer datasheet pin-description table should be used for final PCB and polarity verification.

This page combines the core electrical characteristics, practical application guidance, package information, and clearly qualified drop-in alternatives for LM258DG4. It is intended to accelerate component selection while keeping the final design decisions tied to the Texas Instruments datasheet and application-specific operating limits.

Alternativas directas para LM258DG4 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con LM258DG4 (mismo factor de forma y huella) — difiere en Package, Slew Rate, RoHS Status, Input Offset Voltage, Number of Channels.

STMicroelectronics
Package: 8-pin SOIC
RoHS Status: unknown
Comparar con LM258DG4 →
onsemi
Package: 8-pin SOIC
Slew Rate: 0.6 V/µs
RoHS Status: ROHS3 compliant
Comparar con LM258DG4 →
Texas Instruments
Package: 8-pin SOIC
Slew Rate: 0.3 V/µs
RoHS Status: unknown
Comparar con LM258DG4 →
Texas Instruments
Package: 8-SOIC (D)
Input Offset Voltage: 2 mV (typical)
Number of Channels: 2
Comparar con LM258DG4 →
STMicroelectronics
Package: SOIC-14
Slew Rate: 0.4 V/µs typical
RoHS Status: Compliant
Comparar con LM258DG4 →

LM258DR

✅ Sustitución directa
STMicroelectronics
📦 8-SOIC
2 circuits · Two independent, internally frequency-compensated operational amplifiers · 30 V · 700 kHz · Single supply or split supply · Extends toward ground and VEE · Low-power class · Standard general-purpose amplifier

Consulte el precio

Ver hoja de datos →

LM258DR2G

✅ Sustitución directa
onsemi
📦 8-SOIC
2 channels · 3 V to 32 V · 0.6 V/µs · -25°C to +85°C · 0.7 mA · 2 mV · 2 nA · 15 nA

Consulte el precio

Ver hoja de datos →

LM258DRG4

✅ Sustitución directa
Texas Instruments
📦 8-SOIC
Dual general-purpose operational amplifier · 2 amplifiers · 30 V · ±1.5 V to ±16 V · 3 V · 700 kHz · 0.3 V/µs · -25°C to 85°C

Consulte el precio

Ver hoja de datos →

LM2904DR

✅ Sustitución directa
Texas Instruments
📦 8-SOIC
2 · 3 V to 26 V · ±1.5 V to ±13 V · 700 kHz · 0.3 V/us · 2 mV (typical) · 500 uA (typical) · 0.7 mA (typical)

Consulte el precio

Ver hoja de datos →

LM324DT

✅ Sustitución directa
STMicroelectronics
📦 8-SOIC
4 · 3 V to 32 V · ±1.5 V to ±16 V · 700 µA typical · 2 mV typical · 20 nA typical · 1.3 MHz typical · 0.4 V/µs typical

✓ En stock

$0.0827 / unidad

Ver hoja de datos →

LM258DG4 Valores máximos y características eléctricas

Amplifier Type General Purpose
Number of Amplifiers 2 circuits
Number of Channels 2 channels
Gain-Bandwidth Product 700 kHz
Slew Rate 0.3 V/us
Single-Supply Operating Voltage 3 V to 32 V
Dual-Supply Operating Voltage ±1.5 V to ±16 V
Quiescent Current per Amplifier 0.7 mA typical
Input Offset Voltage 3 mV typical
Input Offset Current 2 nA typical
Input Bias Current 20 nA typical
Common-Mode Input Range Includes ground
Differential Input Voltage Range ±32 V
Frequency Compensation Internal
Encapsulado 8-SOIC, 0.154 inch body width
Package Width 3.90 mm
Tipo de montaje Surface Mount

Configuración de pines de LM258DG4

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 OUT1 — Output of amplifier 1
Pin 2 IN1- — Inverting input of amplifier 1
Pin 3 IN1+ — Non-inverting input of amplifier 1
Pin 4 V- — Negative supply or ground connection
Pin 5 IN2+ — Non-inverting input of amplifier 2
Pin 6 IN2- — Inverting input of amplifier 2
Pin 7 OUT2 — Output of amplifier 2
Pin 8 V+ — Positive supply connection

Aplicaciones típicas

LM258DG4 es adecuado para 6 aplicacións: Industrial Sensor Signal Conditioning, Single-Supply Audio Preamplifier, Battery-Powered Monitoring Equipment, DC Motor Feedback Control, Threshold and Window Detection, Active Filtering and Analog Control.

🏭

Industrial Sensor Signal Conditioning

The LM258DG4 fits low-frequency sensor interfaces where the sensed voltage can approach ground and the circuit uses a single positive supply. Its common-mode input range includes ground, while the 3 V to 32 V operating range supports multiple industrial rails. The 700 kHz gain-bandwidth product is appropriate for pressure, temperature, and position signals rather than high-frequency transducers. Designers should include the typical 3 mV input offset and 20 nA bias current when defining the accuracy budget, while the 0.3 V/us slew rate prevents abrupt large-signal settling.

🎧

Single-Supply Audio Preamplifier

The LM258DG4 can provide voltage gain for low-level audio or control signals in a single-supply system. Its common-mode range includes ground, enabling biased input signals close to 0 V, and the internally compensated amplifier simplifies stable gain configuration. The 700 kHz gain-bandwidth product covers the audio band, while the 0.3 V/us slew rate is adequate for modest signal amplitudes. Headroom must remain between the input and output limits, and the 3 mV typical offset can create audible noise in very quiet stages unless gain and filtering are selected carefully.

🔋

Battery-Powered Monitoring Equipment

The LM258DG4 is appropriate for portable monitoring equipment that prioritizes low supply-current consumption over high bandwidth. The LM258 family specifies a 0.7 mA typical supply-current drain per amplifier and can operate from a 3 V supply, allowing operation from regulated battery rails without a high-voltage supply requirement. The common-mode input range including ground supports sensors powered from the same rail. Because the amplifier is not rail-to-rail at every output condition, the usable signal range and output-swing limits must be checked against the battery voltage.

⚡

DC Motor Feedback Control

The LM258DG4 can amplify a motor-position or current-feedback signal within a control loop while operating from an industrial voltage rail. Its 700 kHz gain-bandwidth product and 0.3 V/us slew rate support common feedback-control bandwidths, and the 3 V to 32 V supply range accommodates legacy 12 V and 24 V systems. Internal frequency compensation supports straightforward closed-loop implementation. Loop stability, output saturation recovery, and common-mode limits should be verified with the motor driver and worst-case supply tolerances because electrical offsets can influence steady-state control error.

📺

Threshold and Window Detection

The LM258DG4 is commonly used as an open-loop comparator for threshold, level, or window detection because it can accept inputs whose common-mode range includes ground. With a 3 V to 32 V single-supply range, it suits low-voltage logic-level sensing as well as higher-voltage industrial signals. The 3 mV typical input offset and 20 nA typical bias current determine threshold accuracy and input loading. A reference voltage must remain inside the allowable common-mode range, and output pull-up or pull-down arrangements may be required for the intended logic interface.

🔧

Active Filtering and Analog Control

The LM258DG4 can implement active filters and proportional analog-control paths when the signal bandwidth is well below its 700 kHz gain-bandwidth product. Its dual channels can form a two-stage amplifier, active filter, or cascaded controller while consuming approximately 0.7 mA per amplifier typically. Internally compensated operation simplifies many voltage-feedback designs, although filter component tolerances and amplifier offset still influence cutoff frequency and DC accuracy. Avoid operating the outputs near the supply rails, and check the common-mode range before including the device in a precision filter.

What are the key specifications of LM258DG4 that engineers should know?
The LM258DG4 is a dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product, 0.3 V/us slew rate, and operation from 3 V to 32 V on a single supply. According to the Texas Instruments LM258 datasheet, it uses 0.7 mA typical supply-current drain per amplifier and provides internal frequency compensation. The device is packaged in an 8-pin SOIC, and its common-mode input range includes ground for practical single-supply sensing near 0 V.
Where can I download the LM258DG4 datasheet PDF?
The LM258DG4 datasheet PDF can be downloaded from the manufacturer datasheet link listed on this page. The document describes the dual-amplifier configuration, electrical characteristics, typical performance curves, pin functions, and application information. According to Texas Instruments, the LM258 family is an industry-standard dual operational-amplifier design intended for broad supply-voltage operation and low supply-current consumption.
Where can I find the LM258DG4 pinout?
The LM258DG4 uses an 8-pin SOIC with standard dual-amplifier assignments: outputs at pins 1 and 7, inverting inputs at pins 2 and 6, non-inverting inputs at pins 3 and 5, ground at pin 4, and positive supply at pin 8. Use the pin-description table in the Texas Instruments datasheet when assigning PCB tracks because pin 1 orientation must follow the package marker.
Can LM258DG4 operate from a single 5 V supply?
Yes, the LM258DG4 can operate from a 5 V single supply because its specified single-supply range is 3 V to 32 V. According to the Texas Instruments LM258 datasheet, the common-mode input range includes ground, making the device suitable for sensor outputs near the lower rail. Verify the required output swing and load current because the input range does not imply that the output can reach every supply voltage exactly.
What is the gain-bandwidth product of LM258DG4?
The LM258DG4 has a typical gain-bandwidth product of 700 kHz. According to the Texas Instruments LM258 datasheet, this bandwidth supports general-purpose closed-loop amplification and filtering rather than high-speed signal processing. At a gain of 10, the approximate closed-loop bandwidth is 70 kHz, while a voltage follower offers approximately 700 kHz bandwidth before accounting for gain-bandwidth-product variation and practical stability margin.
What is the typical slew rate of LM258DG4?
The LM258DG4 has a typical slew rate of 0.3 V/us. According to the Texas Instruments LM258 datasheet, this value limits how quickly the output can follow a large voltage step. It is suitable for sensor signals, control voltages, and audio-band applications, but it is not optimized for fast pulse edges, high-frequency waveform generation, or wideband communications signals.
Where can I buy LM258DG4 and check its price?
Use the Request a Quote form on this page to request LM258DG4 pricing, availability, lead time, and order quantity. The form allows purchasing teams to obtain a current quotation for the exact 8-pin SOIC ordering code without relying on a static price that can become outdated. The requested MPN should be written as LM258DG4 when submitting the request.
What is the lead time for LM258DG4?
The current lead time for LM258DG4 should be requested through the Request a Quote form on this page. Lead time can vary with the requested quantity, shipment configuration, and current supplier allocation. Include the tube or other required shipping format in the request so that the quotation reflects the intended production assembly method.
Is LM258DG4 in stock?
Current LM258DG4 inventory status should be confirmed through the Request a Quote form on this page. Because stock levels and production allocation can change rapidly, request the exact MPN and required quantity through that form. The part is listed for current sourcing, but an order confirmation should remain the authoritative indication of available supply.
What can replace LM258DG4?
LM258DG4 can be replaced by pin-compatible LM258-family ordering codes when their temperature, screening, and shipping options meet the design requirements. LM2904 and LM324 are also dual-amplifier SOIC alternatives cited in LM358-equivalent references, but their operating limits and performance differ. Confirm pin assignments, supply range, common-mode range, offset, bandwidth, and temperature rating in the manufacturer datasheet before releasing a substitution.
What is the best LM2904 equivalent for LM258DG4?
The LM2904 is a dual operational amplifier that can serve as a functional alternative to LM258DG4 in many 8-pin SOIC circuits, but it is not a blanket drop-in choice. According to LM358-equivalent references, LM2904 shares the general dual-amplifier architecture and pin arrangement. Its supply-voltage ceiling, input characteristics, bandwidth, and temperature grade must be compared with the LM258 requirements before selecting it.
What is the difference between LM258DG4 and LM258DR?
LM258DG4 and LM258DR share the same LM258 dual-amplifier family, 8-pin SOIC footprint, 700 kHz gain-bandwidth product, and 0.3 V/us slew rate. Their principal documented difference is the ordering or shipping suffix rather than a change in the core performance values. Confirm the exact temperature grade, reel configuration, and any qualification markings required by the finished product before substituting one code for the other.
Is LM324 the same as LM258DG4?
No, LM324 is similar to LM258DG4 but is not electrically identical. According to the LM358-equivalent reference, both use an 8-pin dual-amplifier arrangement, while the LM324 is commonly associated with a 1 MHz gain-bandwidth product rather than the LM258's 700 kHz. The faster bandwidth can change stability and noise behavior, and the operating limits must be checked for the intended supply and temperature range.
When should I choose LM258DG4 instead of LM2904?
Choose LM258DG4 when the circuit is designed around the LM258 family's 700 kHz bandwidth, 0.3 V/us slew rate, low supply-current drain, and specified common-mode behavior. Choose LM2904 when its alternative electrical ratings better match the actual application. For either device, compare input offset, input bias current, output swing, supply limits, operating temperature, and channel-to-channel behavior rather than relying only on the shared package.
Is LM258DG4 suitable for sensor and industrial control applications?
Yes, LM258DG4 is suitable for many sensor and industrial-control signal-conditioning circuits. Its 700 kHz gain-bandwidth product, 0.3 V/us slew rate, 3 V to 32 V single-supply range, and common-mode input capability that includes ground support low-frequency sensor signals and process-control voltages. For precision measurement, include the 3 mV typical input offset and 20 nA typical bias current in the error budget.

Datos de referencia de ingeniería para LM258DG4 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose LM258DG4 for legacy-style single-supply signal conditioning where low supply current, a common-mode input range that includes ground, and a 700 kHz gain-bandwidth product are important. LM258DR, LM258DR2G, and LM258DRG4 are the closest ordering-code choices when their temperature grade, qualification marking, and shipment configuration meet the finished-product requirements. LM2904 is appropriate when its electrical characteristics and higher 36 V supply ceiling provide a specific design benefit, but it should not replace the LM258 without checking offset, bias current, common-mode limits, and bandwidth. LM324 provides more bandwidth, approximately 1 MHz versus 700 kHz, which may suit some wider-band filters but can alter loop gain, stability, noise, and transient response. For all candidates, verify the 8-pin SOIC footprint, pin functions, supply range, temperature rating, output swing, and production qualifications before release.

Comparación con alternativas

Parámetro Este producto LM258DR LM258DR2G LM258DRG4 LM2904 LM324
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments STMicroelectronics STMicroelectronics
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Number of Amplifiers 2 2 2 2 2 2
Maximum Single-Supply Voltage 32 V 32 V 32 V 32 V 36 V 30 V

Diferenciadores clave

  • Matches the 700 kHz bandwidth of the closest LM258 ordering variants (frente a LM258DR)
  • Lower listed supply-voltage ceiling than the LM2904 option (frente a LM2904)
  • Lower bandwidth can simplify familiarity with legacy LM258 loop compensation (frente a LM324)

Notas de diseño

Calculate the worst-case supply dissipation from the actual output voltage, load current, and quiescent current. For a single 5 V supply at a 2.5 V output and 10 mA load, the estimated load dissipation is (5 V - 2.5 V) × 0.01 A = 25 mW, while each amplifier adds approximately 0.7 mA of quiescent current. These estimates use VIN = 5 V, VOUT = 2.5 V, IOUT = 10 mA, and IQ = 0.7 mA per amplifier. Include regulator tolerances, output-load transients, and adjacent heat sources in the final thermal margin.

Place the decoupling capacitor from the positive supply pin to ground as close as practical to the SOIC, and keep the ground connection short and low-impedance. Route the two inverting inputs directly to their feedback resistors or sensing source to minimize parasitic capacitance and susceptibility to interference. For the common-mode input range that includes ground, maintain a clean ground reference under the package because input offset and bias-current errors are strongly influenced by ground-potential differences.

Do not assume that an input or output can swing exactly to 0 V or the positive supply rail. Although the common-mode input range includes ground, output swing and input range boundaries depend on supply voltage, load, output configuration, and device grade. Check the output-voltage swing curves and electrical limits for the highest signal and lowest supply condition. Also avoid using input or output pins as power rails, and verify that adjacent package pins are not left inconsistent with the selected single- or dual-supply topology.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not explicitly identified in the cited listings. AEC-Q100 qualification is not indicated for this general-purpose amplifier ordering code.

Datos verificados el: 2026-11-10 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

LM258DG4 datasheet LM258DG4 pinout LM258DG4 datasheet pdf LM258DG4 specifications Texas Instruments LM258DG4 LM258DG4 equivalent LM258DG4 replacement LM258DG4 vs LM2904 LM258DG4 vs LM324 LM258DG4 700 kHz amplifier LM258DG4 8-SOIC LM258DG4 sensor application LM258DG4 price LM258DG4 stock LM258DG4 schematic

Componentes & términos relacionados

Texas Instruments LM258DG4 LM258DR LM258DR2G LM258DRG4 LM2904 LM324 operational amplifier dual operational amplifier general-purpose amplifier analog IC integrated circuit semiconductor single-supply amplifier gain-bandwidth product slew rate common-mode input range input offset voltage input bias current internal frequency compensation 8-SOIC SOIC package family surface-mount package industrial sensor conditioning motor feedback control
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ