LM2901NG4 - Quad Open-Collector Comparator | Texas Instruments
MPN: LM2901NG4 ✓ AktifLM2901NG4 Ringkasan
A comparator is an analog integrated circuit that converts the relationship between two voltages into a binary result. The LM2901 belongs to the voltage-comparator hierarchy within the broader amplifier and comparator IC family. Its four independent channels make it useful when a system needs several threshold, level, or crossing-point decisions without using four separate single comparator packages.
The LM2901NG4 supports single supplies from 2 V to 30 V and dual supplies from ±1 V to ±15 V. According to the manufacturer product page, its outputs are compatible with TTL, MOS, and CMOS logic. The wide supply range allows the same device to be used in low-voltage control circuits and higher-voltage industrial interfaces, provided each input and output node remains within its applicable voltage limits.
Each comparator channel is electrically independent, allowing four separate threshold decisions within one package. The open-collector output requires an external pull-up resistor to establish a valid high output state. This arrangement provides flexible interface-voltage selection and can improve system fault tolerance because a wired output can be pulled down by more than one channel. The device does not actively drive the output high.
Typical applications include industrial control and threshold detection, instrumentation signal conditioning, sensor-interface decisions, level translation, and general analog signal processing. The four-channel organization is particularly useful for monitoring multiple control lines, implementing window comparators, or creating digital alarm logic. Open-collector outputs also suit systems that require a wired-AND bus or a pull-up voltage different from the comparator supply.
When laying out a circuit, place the pull-up resistor and any input filtering components close to the relevant device pins, and route sensitive analog inputs away from switching nodes. Verify the common-mode range, differential input range, supply limits, and output pull-up voltage for the exact operating conditions. The 14-PDIP package is intended for through-hole assembly rather than compact surface-mount designs.
This page combines the LM2901NG4 operating limits, interface characteristics, application guidance, package details, and validated drop-in alternatives with practical design notes for engineers comparing legacy quad comparators.
Pilihan pengganti yang segera untuk LM2901NG4 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera LM2901NG4 (sama faktor bentuk dan kaki) — berbeza dalam Logic Compatibility, Package, Number of Channels, Output Type, Mounting Type.
LM2901N
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →LM2901NG
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM339N
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →LM2901NG4 Penilaian maksimum & Ciri-ciri Elektrik
| Comparator Type | Quad differential comparator |
| Number of Channels | 4 channels |
| Jenis Output | Open collector |
| Supply Voltage Range, Single Supply | 2 V to 30 V |
| Supply Voltage Range, Dual Supply | ±1 V to ±15 V |
| Gambaran Suhu Operasi | -40 °C to 125 °C |
| Kemasan | 14-PDIP, 0.300 inch pitch, 7.62 mm |
| Logic Compatibility | TTL, MOS, and CMOS compatible |
| Output Pull-Up Requirement | External pull-up resistor required |
Panduan Konfigurasi Pin LM2901NG4 14-pdip, 0.300 inch pitch, 7.62 mm
Konfigurasi pin untuk LM2901NG4 (14-pdip, 0.300 inch pitch, 7.62 mm pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk LM2901NG4.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
LM2901NG4 patut untuk 6 aplikasis: Industrial Threshold Detection, Instrumentation Signal Conditioning, Sensor Interface Logic, Power Supply Monitoring, Motor Control and Feedback, Digital Logic Level Conditioning.
Industrial Threshold Detection
The LM2901NG4 fits industrial threshold-detection tasks that require four independent comparisons within a 2 V to 30 V single-supply system. Each channel can establish a switching boundary for a sensor or control signal, while its open-collector output provides a flexible logic interface when paired with a pull-up resistor. The -40 °C to 125 °C operating range supports equipment exposed to extended temperature variation. Design protection around external wiring and verify that sensor inputs remain within the comparator’s common-mode limits.
Disebarkan
Instrumentation Signal Conditioning
The LM2901NG4 is useful in instrumentation circuits that convert analog measurements into threshold events. Four independent channels can monitor a measurement window, detect several alarm boundaries, or compare a conditioned sensor signal against separate references. Its open-collector outputs can pull up to the instrumentation system’s selected logic voltage rather than requiring the output high voltage to equal the comparator supply. Keeping the four analog paths short and away from switching circuitry helps preserve the integrity of the decision signals.
Disebarkan
Sensor Interface Logic
The LM2901NG4 can convert sensor-derived voltages into open-collector logic events for monitoring, alarm, or actuator-control circuits. Its four-channel organization allows one package to handle several independently sensed quantities, and the broad 2 V to 30 V single-supply range supports both low-energy sensors and industrial signal levels. An external pull-up resistor establishes the digital high state, while careful common-mode and differential-input checks ensure that sensor transitions are compared correctly.
Disebarkan
Power Supply Monitoring
The LM2901NG4 can supervise several power-related thresholds in a 2 V to 30 V system by comparing divided supply voltages against references. Four open-collector channels can provide separate undervoltage, overvoltage, or sequence-related indications, with each output connected to a pull-up resistor. The wide -40 °C to 125 °C range is useful in power-conversion equipment, but designers must include suitable input filtering and account for the voltage drop across feedback dividers.
Disebarkan
Motor Control and Feedback
The LM2901NG4 can support low-voltage motor-control systems that require independent limit, direction, or feedback comparisons. Each open-collector channel can report a control event to a logic device or participate in a wired-AND alarm function. Operating from 2 V to 30 V allows use in compact control boards and broader industrial controllers, while the -40 °C to 125 °C range covers demanding ambient conditions. Motor transients still require external filtering, clamping, and careful grounding.
Disebarkan
Digital Logic Level Conditioning
The LM2901NG4 is suitable for level conditioning when a system needs an open-collector interface rather than a push-pull logic driver. The outputs are compatible with TTL, MOS, and CMOS logic, and the pull-up voltage can be selected independently to suit the receiving circuit. Four channels allow multiple signal decisions to be handled together. Because open-collector outputs sink current rather than source it, the pull-up resistor value and total sink current must be selected with the output load in mind.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LM2901NG4 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | LM2901N | LM2901NG | LM339N |
|---|---|---|---|---|
| Package | 14-PDIP | 14-PDIP | 14-PDIP | 14-DIP |
| Brand | Texas Instruments | Texas Instruments | onsemi | Texas Instruments |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels |
Penyeberangsung Jelas
- Four independent channels in one through-hole package (vsLM2901NG)
- Single-supply operating range aligned with 30 V industrial systems (vsLM339N)
- Open-collector interface supports flexible logic pull-up (vsLM2901NG)
Catatan Desain
Do not treat the open-collector output as a push-pull logic output. Each used output requires a pull-up resistor to the intended logic rail, and the resistor must be sized for the input current, leakage current, switching speed, and maximum sink-current requirement. Connecting an output directly to a supply or ground without a current-limiting arrangement can exceed the device’s output ratings and damage the comparator channel.
Keep comparator inputs short and route them away from high-current switching paths. Place input filtering or clamp components close to the relevant pins, use a compact ground-return path, and avoid sharing narrow copper traces between sensitive inputs and power-stage connections. If several open-collector outputs share one pull-up node, route the individual channels so that a switching output does not capacitively disturb adjacent analog inputs.
Validate the actual channel count used, the pull-up voltage, and the total output sink current before assigning the LM2901NG4 supply. Although the device supports single supplies from 2 V to 30 V and dual supplies from ±1 V to ±15 V, the selected operating mode still must satisfy each input’s common-mode and differential limits. Account for supply-current changes and output-state transitions when sizing the upstream regulator and bypass capacitance.
Maklumat Kesediaan
The verified product information does not state the RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status of LM2901NG4.