Texas Instruments

LM2901NG4 - Quad Open-Collector Comparator | Texas Instruments

部品番号: LM2901NG4 ✓ 生産中
2 V to 30 V Vdss 14-PDIP, 0.300 inch pitch, 7.62 mm Package
MOQ: 1 |

LM2901NG4 概要

The Texas Instruments LM2901NG4 is a four-channel general-purpose differential comparator with open-collector outputs, single-supply operation from 2 V to 30 V, and a 14-PDIP package. Each of the four independent channels compares two input voltages and provides a logic-level indication of their relationship. The open-collector architecture allows the outputs to be pulled up to a suitable logic voltage and enables wired-AND operation when multiple channels share an output node.

A comparator is an analog integrated circuit that converts the relationship between two voltages into a binary result. The LM2901 belongs to the voltage-comparator hierarchy within the broader amplifier and comparator IC family. Its four independent channels make it useful when a system needs several threshold, level, or crossing-point decisions without using four separate single comparator packages.

The LM2901NG4 supports single supplies from 2 V to 30 V and dual supplies from ±1 V to ±15 V. According to the manufacturer product page, its outputs are compatible with TTL, MOS, and CMOS logic. The wide supply range allows the same device to be used in low-voltage control circuits and higher-voltage industrial interfaces, provided each input and output node remains within its applicable voltage limits.

Each comparator channel is electrically independent, allowing four separate threshold decisions within one package. The open-collector output requires an external pull-up resistor to establish a valid high output state. This arrangement provides flexible interface-voltage selection and can improve system fault tolerance because a wired output can be pulled down by more than one channel. The device does not actively drive the output high.

Typical applications include industrial control and threshold detection, instrumentation signal conditioning, sensor-interface decisions, level translation, and general analog signal processing. The four-channel organization is particularly useful for monitoring multiple control lines, implementing window comparators, or creating digital alarm logic. Open-collector outputs also suit systems that require a wired-AND bus or a pull-up voltage different from the comparator supply.

When laying out a circuit, place the pull-up resistor and any input filtering components close to the relevant device pins, and route sensitive analog inputs away from switching nodes. Verify the common-mode range, differential input range, supply limits, and output pull-up voltage for the exact operating conditions. The 14-PDIP package is intended for through-hole assembly rather than compact surface-mount designs.

This page combines the LM2901NG4 operating limits, interface characteristics, application guidance, package details, and validated drop-in alternatives with practical design notes for engineers comparing legacy quad comparators.

ドロップイン代替品: LM2901NG4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: LM2901NG4 (同一形状・フットプリント) — 相違点: Logic Compatibility, Package, Number of Channels, Output Type, Mounting Type.

Texas Instruments
Logic Compatibility: TTL, DTL, MOS, ECL, and CMOS output compatibility
Package: 14-pin DIP
Mounting Type: Through hole
比較対象 LM2901NG4 →
onsemi
Logic Compatibility: TTL and CMOS
Mounting Type: Through-hole
比較対象 LM2901NG4 →
Texas Instruments
Package: 14-pin PDIP
Number of Channels: 4
Output Type: Open-collector
比較対象 LM2901NG4 →

LM2901N

✅ ドロップイン ⚠️ 仕様未検証
Texas Instruments
📦 14-PDIP
Quad differential comparator · 4 channels · Single or split supply · 36 V · 25 nA typical · ±5.0 nA typical · 800 µA typical · Open collector

価格はお問い合わせください

データシートを見る →

LM2901NG

✅ ドロップイン
onsemi
📦 14-PDIP
Quad differential comparator · 4 channels · 3 V to 36 V · Single supply · Open collector · TTL and CMOS · 130 mV at 4 mA · Includes ground

価格はお問い合わせください

データシートを見る →

LM339N

✅ ドロップイン ⚠️ 仕様未検証
Texas Instruments
📦 14-PDIP
Quad differential comparator · 4 · 2 V to 36 V · +/- 1 V to +/- 18 V · 1.3 microseconds · Open-collector · 14-pin PDIP · Through-hole

価格はお問い合わせください

データシートを見る →

LM2901NG4 最大定格&電気的特性

Comparator Type Quad differential comparator
Number of Channels 4 channels
出力タイプ Open collector
Supply Voltage Range, Single Supply 2 V to 30 V
Supply Voltage Range, Dual Supply ±1 V to ±15 V
動作温度範囲 -40 °C to 125 °C
パッケージ 14-PDIP, 0.300 inch pitch, 7.62 mm
Logic Compatibility TTL, MOS, and CMOS compatible
Output Pull-Up Requirement External pull-up resistor required

LM2901NG4 14-pdip, 0.300 inch pitch, 7.62 mm ピン配置ガイド

LM2901NG4 (14-pdip, 0.300 inch pitch, 7.62 mm パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。

LM2901NG4 の 14-pdip, 0.300 inch pitch, 7.62 mm パッケージピン配置図

詳細なピン配置データはありません: LM2901NG4.

詳細は データシート をご参照ください。

主な用途

LM2901NG4 の用途: 6 件s: Industrial Threshold Detection, Instrumentation Signal Conditioning, Sensor Interface Logic, Power Supply Monitoring, Motor Control and Feedback, Digital Logic Level Conditioning.

🏭

Industrial Threshold Detection

The LM2901NG4 fits industrial threshold-detection tasks that require four independent comparisons within a 2 V to 30 V single-supply system. Each channel can establish a switching boundary for a sensor or control signal, while its open-collector output provides a flexible logic interface when paired with a pull-up resistor. The -40 °C to 125 °C operating range supports equipment exposed to extended temperature variation. Design protection around external wiring and verify that sensor inputs remain within the comparator’s common-mode limits.

🔧

Instrumentation Signal Conditioning

The LM2901NG4 is useful in instrumentation circuits that convert analog measurements into threshold events. Four independent channels can monitor a measurement window, detect several alarm boundaries, or compare a conditioned sensor signal against separate references. Its open-collector outputs can pull up to the instrumentation system’s selected logic voltage rather than requiring the output high voltage to equal the comparator supply. Keeping the four analog paths short and away from switching circuitry helps preserve the integrity of the decision signals.

🧩

Sensor Interface Logic

The LM2901NG4 can convert sensor-derived voltages into open-collector logic events for monitoring, alarm, or actuator-control circuits. Its four-channel organization allows one package to handle several independently sensed quantities, and the broad 2 V to 30 V single-supply range supports both low-energy sensors and industrial signal levels. An external pull-up resistor establishes the digital high state, while careful common-mode and differential-input checks ensure that sensor transitions are compared correctly.

⚡

Power Supply Monitoring

The LM2901NG4 can supervise several power-related thresholds in a 2 V to 30 V system by comparing divided supply voltages against references. Four open-collector channels can provide separate undervoltage, overvoltage, or sequence-related indications, with each output connected to a pull-up resistor. The wide -40 °C to 125 °C range is useful in power-conversion equipment, but designers must include suitable input filtering and account for the voltage drop across feedback dividers.

🏭

Motor Control and Feedback

The LM2901NG4 can support low-voltage motor-control systems that require independent limit, direction, or feedback comparisons. Each open-collector channel can report a control event to a logic device or participate in a wired-AND alarm function. Operating from 2 V to 30 V allows use in compact control boards and broader industrial controllers, while the -40 °C to 125 °C range covers demanding ambient conditions. Motor transients still require external filtering, clamping, and careful grounding.

🖥️

Digital Logic Level Conditioning

The LM2901NG4 is suitable for level conditioning when a system needs an open-collector interface rather than a push-pull logic driver. The outputs are compatible with TTL, MOS, and CMOS logic, and the pull-up voltage can be selected independently to suit the receiving circuit. Four channels allow multiple signal decisions to be handled together. Because open-collector outputs sink current rather than source it, the pull-up resistor value and total sink current must be selected with the output load in mind.

What is the operating voltage range of LM2901NG4?
The LM2901NG4 operates from 2 V to 30 V with a single supply and from ±1 V to ±15 V with dual supplies. According to the Texas Instruments LM2901 product information, the wide operating range supports both low-voltage logic circuits and higher-voltage industrial systems. The circuit designer must also confirm that every input voltage and pull-up voltage remains within the limits of the selected operating condition.
How many comparators are in LM2901NG4?
The LM2901NG4 contains four independent differential comparator channels in one 14-PDIP package. According to the Texas Instruments product description, it is a general-purpose quad comparator, and each channel can perform a separate threshold or voltage-crossing decision. The open-collector outputs require pull-up resistors, while the four independent channels permit simultaneous monitoring or control functions without separate single-channel packages.
Does LM2901NG4 have open-collector outputs?
Yes, all four LM2901NG4 channels use open-collector outputs. According to the manufacturer product information, the outputs are compatible with TTL, MOS, and CMOS logic. Because an open-collector stage can pull low but cannot actively drive high, each output needs an external pull-up resistor connected to the desired logic supply. Multiple channels may also share a pull-up for wired-AND operation.
What is the LM2901NG4 operating temperature range?
The LM2901NG4 is specified for an operating temperature range of -40 °C to 125 °C. The Texas Instruments LM2901 family information identifies the device for general-purpose industrial and instrumentation applications across that range. Temperature qualification does not replace careful DC and transient design: input common-mode voltage, supply voltage, output current, and power dissipation must remain valid at the highest ambient temperature expected in the finished equipment.
Where can I download the LM2901NG4 datasheet PDF?
The official Texas Instruments LM2901 product page is the appropriate starting point for the LM2901NG4 datasheet, electrical characteristics, ordering information, and package drawings. The same page also identifies the LM2901B as a drop-in replacement for LM239, LM339, and original LM2901 versions. Use the LM2901NG4 orderable-part information and the package data to confirm the 14-PDIP configuration before beginning a PCB or firmware revision.
Where can I find the LM2901NG4 pinout?
The LM2901NG4 pin assignment is shown in the pin-configuration section of the manufacturer datasheet. The device is a 14-PDIP containing four differential comparator channels, a common supply connection, ground, and four open-collector outputs. Use the numbered package drawing rather than inferring connections from a different LM2901 package, because ordering suffixes and package variants can use different physical formats.
What can replace LM2901NG4?
The LM2901NG4 can be replaced by a pin-compatible quad open-collector comparator that uses the same 14-PDIP footprint and satisfies the original supply, common-mode, offset-current, and temperature requirements. The Texas Instruments LM2901N is the closest ordering option, while the onsemi LM2901NG is a cross-brand 14-PDIP alternative. The LM339N is also a legacy quad comparator option, but its supply and input limits must be checked against the original design.
Is LM2901NG4 the same as onsemi LM2901NG?
The Texas Instruments LM2901NG4 and onsemi LM2901NG are both quad open-collector comparators offered in a 14-PDIP format, but interchangeability must be established from the individual electrical tables. Check supply current, input offset voltage, input bias current, common-mode range, differential input range, propagation delay, output saturation voltage, and temperature grade. The manufacturer product information also states that the LM2901B is a drop-in replacement for legacy LM2901, LM339, and LM239 versions.
LM2901NG4 vs LM339N - which is better for a 30 V industrial control circuit?
The LM2901NG4 is usually the better match for a circuit whose supply remains at or below 30 V, while the LM339N supports a wider single-supply range extending to 36 V. Both provide four comparator channels and open-collector outputs in 14-pin DIP packages. The Texas Instruments LM2901 family information identifies the LM2901B as a drop-in replacement for LM339, but designers should still compare input common-mode limits and output-current requirements.
When should I choose LM2901NG4 over LM2901NG?
Choose LM2901NG4 when the finished product requires the Texas Instruments source, the specific 14-PDIP ordering configuration, and the documented LM2901 electrical limits across -40 °C to 125 °C. The onsemi LM2901NG is useful when its cross-brand sourcing and electrical characteristics are acceptable. For either device, verify the pull-up voltage, input common-mode range, output sink current, supply current, and production qualification before approving a substitution.
Is LM2901NG4 suitable for industrial threshold detection?
The LM2901NG4 is suitable for many industrial threshold-detection circuits because it combines four independent comparator channels, a 2 V to 30 V single-supply range, and a -40 °C to 125 °C operating range. Its open-collector outputs can interface with TTL, MOS, or CMOS logic through pull-up resistors. Industrial suitability still depends on transient protection, sensor grounding, diagnostic coverage, and compliance requirements for the finished equipment.
Where can I buy LM2901NG4 and what is its lead time?
Use the Request a Quote form on this page to request LM2901NG4 availability, current commercial terms, and lead time for the exact 14-PDIP ordering configuration. Stock and lead time can change with manufacturing conditions, so confirm the quantity, shipment location, and target date when requesting the quotation. The manufacturer product page and its ordering information are the appropriate references for identifying the exact device.
What is the price of LM2901NG4?
Current commercial pricing for LM2901NG4 is best obtained through the Request a Quote form on this page. Quote requests can account for the requested quantity, procurement method, delivery location, and current factory availability. For engineering comparisons, use the structured product data rather than a historical listing price, because legacy comparator pricing and inventory can change independently of the device’s technical specifications.
Is LM2901NG4 in stock?
LM2901NG4 availability should be confirmed through the Request a Quote form on this page for the exact quantity and required delivery date. The component is offered by multiple authorized channels, but listing status does not guarantee inventory for every order quantity. A quotation response provides the most appropriate confirmation for current stock, production allocation, and lead time.
What are the key specifications of LM2901NG4 that engineers should know?
The key LM2901NG4 specifications are four independent comparator channels, open-collector outputs, a 2 V to 30 V single-supply range, ±1 V to ±15 V dual-supply operation, and a -40 °C to 125 °C temperature range. According to the Texas Instruments product page, the outputs support TTL, MOS, and CMOS interfaces. The device uses a 14-PDIP package and requires an external pull-up resistor on each used output.

エンジニアリング参考データ: LM2901NG4 — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose LM2901NG4 when the design needs four independent general-purpose comparisons in a 14-PDIP package, a single-supply operating range of 2 V to 30 V, and operation from -40 °C to 125 °C. Select LM2901N when that exact Texas Instruments ordering configuration is preferred and its complete electrical limits match the original design. Consider onsemi LM2901NG for a cross-brand sourcing option after checking offset voltage, bias current, propagation delay, common-mode range, output sink current, and temperature limits. Choose LM339N when its wider 36 V single-supply capability is useful, but verify the original circuit’s input-range and switching requirements. For every option, confirm the 14-pin DIP footprint, external pull-up arrangement, supply tolerances, and production status before releasing a substitution.

代替品との比較

パラメータ この製品 LM2901N LM2901NG LM339N
Package 14-PDIP 14-PDIP 14-PDIP 14-DIP
Brand Texas Instruments Texas Instruments onsemi Texas Instruments
Comparator Channels 4 channels 4 channels 4 channels 4 channels

主な差別化要因

  • Four independent channels in one through-hole package (vs LM2901NG)
  • Single-supply operating range aligned with 30 V industrial systems (vs LM339N)
  • Open-collector interface supports flexible logic pull-up (vs LM2901NG)

設計ノート

Do not treat the open-collector output as a push-pull logic output. Each used output requires a pull-up resistor to the intended logic rail, and the resistor must be sized for the input current, leakage current, switching speed, and maximum sink-current requirement. Connecting an output directly to a supply or ground without a current-limiting arrangement can exceed the device’s output ratings and damage the comparator channel.

Keep comparator inputs short and route them away from high-current switching paths. Place input filtering or clamp components close to the relevant pins, use a compact ground-return path, and avoid sharing narrow copper traces between sensitive inputs and power-stage connections. If several open-collector outputs share one pull-up node, route the individual channels so that a switching output does not capacitively disturb adjacent analog inputs.

Validate the actual channel count used, the pull-up voltage, and the total output sink current before assigning the LM2901NG4 supply. Although the device supports single supplies from 2 V to 30 V and dual supplies from ±1 V to ±15 V, the selected operating mode still must satisfy each input’s common-mode and differential limits. Account for supply-current changes and output-state transitions when sizing the upstream regulator and bypass capacitance.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The verified product information does not state the RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status of LM2901NG4.

関連検索

lm2901n datasheet LM2901NG4 datasheet LM2901NG4 datasheet pdf LM2901NG4 pinout LM2901NG4 specifications LM2901NG4 equivalent LM2901NG4 replacement LM2901NG4 vs LM339N LM2901NG4 open collector comparator LM2901NG4 14-PDIP LM2901NG4 industrial threshold detection LM2901NG4 price LM2901NG4 stock Texas Instruments LM2901NG4

関連部品&用語

Texas Instruments LM2901NG4 LM2901N LM2901NG LM339N onsemi quad differential comparator comparator IC analog comparator voltage comparator open-collector output TTL CMOS MOS logic 14-PDIP DIP package through-hole package single-supply operation dual-supply operation common-mode input voltage differential input voltage industrial threshold detection instrumentation signal conditioning power-supply monitoring wired-AND logic
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示