LM2901NG4 - Quad Open-Collector Comparator | Texas Instruments
MPN: LM2901NG4 ✓ פעילLM2901NG4 סקירה
A comparator is an analog integrated circuit that converts the relationship between two voltages into a binary result. The LM2901 belongs to the voltage-comparator hierarchy within the broader amplifier and comparator IC family. Its four independent channels make it useful when a system needs several threshold, level, or crossing-point decisions without using four separate single comparator packages.
The LM2901NG4 supports single supplies from 2 V to 30 V and dual supplies from ±1 V to ±15 V. According to the manufacturer product page, its outputs are compatible with TTL, MOS, and CMOS logic. The wide supply range allows the same device to be used in low-voltage control circuits and higher-voltage industrial interfaces, provided each input and output node remains within its applicable voltage limits.
Each comparator channel is electrically independent, allowing four separate threshold decisions within one package. The open-collector output requires an external pull-up resistor to establish a valid high output state. This arrangement provides flexible interface-voltage selection and can improve system fault tolerance because a wired output can be pulled down by more than one channel. The device does not actively drive the output high.
Typical applications include industrial control and threshold detection, instrumentation signal conditioning, sensor-interface decisions, level translation, and general analog signal processing. The four-channel organization is particularly useful for monitoring multiple control lines, implementing window comparators, or creating digital alarm logic. Open-collector outputs also suit systems that require a wired-AND bus or a pull-up voltage different from the comparator supply.
When laying out a circuit, place the pull-up resistor and any input filtering components close to the relevant device pins, and route sensitive analog inputs away from switching nodes. Verify the common-mode range, differential input range, supply limits, and output pull-up voltage for the exact operating conditions. The 14-PDIP package is intended for through-hole assembly rather than compact surface-mount designs.
This page combines the LM2901NG4 operating limits, interface characteristics, application guidance, package details, and validated drop-in alternatives with practical design notes for engineers comparing legacy quad comparators.
חלופות תחליף ישיר עבור LM2901NG4 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LM2901NG4 (אותו גורם צורה וטביעת רגל) — שונים ב Logic Compatibility, Package, Number of Channels, Output Type, Mounting Type.
LM2901N
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2901NG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM339N
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2901NG4 דירוגים מרביים ומאפיינים חשמליים
| Comparator Type | Quad differential comparator |
| Number of Channels | 4 channels |
| סוג פלט | Open collector |
| Supply Voltage Range, Single Supply | 2 V to 30 V |
| Supply Voltage Range, Dual Supply | ±1 V to ±15 V |
| טווח טמפרטורת פעולה | -40 °C to 125 °C |
| מארז | 14-PDIP, 0.300 inch pitch, 7.62 mm |
| Logic Compatibility | TTL, MOS, and CMOS compatible |
| Output Pull-Up Requirement | External pull-up resistor required |
מדריך תצורת פינים של LM2901NG4 14-pdip, 0.300 inch pitch, 7.62 mm
תצורת פינים עבור LM2901NG4 (מארזת 14-pdip, 0.300 inch pitch, 7.62 mm). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור LM2901NG4.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
LM2901NG4 מתאים עבור 6 יישוםs: Industrial Threshold Detection, Instrumentation Signal Conditioning, Sensor Interface Logic, Power Supply Monitoring, Motor Control and Feedback, Digital Logic Level Conditioning.
Industrial Threshold Detection
The LM2901NG4 fits industrial threshold-detection tasks that require four independent comparisons within a 2 V to 30 V single-supply system. Each channel can establish a switching boundary for a sensor or control signal, while its open-collector output provides a flexible logic interface when paired with a pull-up resistor. The -40 °C to 125 °C operating range supports equipment exposed to extended temperature variation. Design protection around external wiring and verify that sensor inputs remain within the comparator’s common-mode limits.
מומלץ
Instrumentation Signal Conditioning
The LM2901NG4 is useful in instrumentation circuits that convert analog measurements into threshold events. Four independent channels can monitor a measurement window, detect several alarm boundaries, or compare a conditioned sensor signal against separate references. Its open-collector outputs can pull up to the instrumentation system’s selected logic voltage rather than requiring the output high voltage to equal the comparator supply. Keeping the four analog paths short and away from switching circuitry helps preserve the integrity of the decision signals.
מומלץ
Sensor Interface Logic
The LM2901NG4 can convert sensor-derived voltages into open-collector logic events for monitoring, alarm, or actuator-control circuits. Its four-channel organization allows one package to handle several independently sensed quantities, and the broad 2 V to 30 V single-supply range supports both low-energy sensors and industrial signal levels. An external pull-up resistor establishes the digital high state, while careful common-mode and differential-input checks ensure that sensor transitions are compared correctly.
מומלץ
Power Supply Monitoring
The LM2901NG4 can supervise several power-related thresholds in a 2 V to 30 V system by comparing divided supply voltages against references. Four open-collector channels can provide separate undervoltage, overvoltage, or sequence-related indications, with each output connected to a pull-up resistor. The wide -40 °C to 125 °C range is useful in power-conversion equipment, but designers must include suitable input filtering and account for the voltage drop across feedback dividers.
מומלץ
Motor Control and Feedback
The LM2901NG4 can support low-voltage motor-control systems that require independent limit, direction, or feedback comparisons. Each open-collector channel can report a control event to a logic device or participate in a wired-AND alarm function. Operating from 2 V to 30 V allows use in compact control boards and broader industrial controllers, while the -40 °C to 125 °C range covers demanding ambient conditions. Motor transients still require external filtering, clamping, and careful grounding.
מומלץ
Digital Logic Level Conditioning
The LM2901NG4 is suitable for level conditioning when a system needs an open-collector interface rather than a push-pull logic driver. The outputs are compatible with TTL, MOS, and CMOS logic, and the pull-up voltage can be selected independently to suit the receiving circuit. Four channels allow multiple signal decisions to be handled together. Because open-collector outputs sink current rather than source it, the pull-up resistor value and total sink current must be selected with the output load in mind.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LM2901NG4 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LM2901N | LM2901NG | LM339N |
|---|---|---|---|---|
| Package | 14-PDIP | 14-PDIP | 14-PDIP | 14-DIP |
| Brand | Texas Instruments | Texas Instruments | onsemi | Texas Instruments |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels |
מבדילים עיקריים
- Four independent channels in one through-hole package (לעומתLM2901NG)
- Single-supply operating range aligned with 30 V industrial systems (לעומתLM339N)
- Open-collector interface supports flexible logic pull-up (לעומתLM2901NG)
הערות תכנון
Do not treat the open-collector output as a push-pull logic output. Each used output requires a pull-up resistor to the intended logic rail, and the resistor must be sized for the input current, leakage current, switching speed, and maximum sink-current requirement. Connecting an output directly to a supply or ground without a current-limiting arrangement can exceed the device’s output ratings and damage the comparator channel.
Keep comparator inputs short and route them away from high-current switching paths. Place input filtering or clamp components close to the relevant pins, use a compact ground-return path, and avoid sharing narrow copper traces between sensitive inputs and power-stage connections. If several open-collector outputs share one pull-up node, route the individual channels so that a switching output does not capacitively disturb adjacent analog inputs.
Validate the actual channel count used, the pull-up voltage, and the total output sink current before assigning the LM2901NG4 supply. Although the device supports single supplies from 2 V to 30 V and dual supplies from ±1 V to ±15 V, the selected operating mode still must satisfy each input’s common-mode and differential limits. Account for supply-current changes and output-state transitions when sizing the upstream regulator and bypass capacitance.
מידע על תאימות
The verified product information does not state the RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status of LM2901NG4.