LM339DTBR2G - Quad Open-Collector Comparator | onsemi
MPN: LM339DTBR2G ✓ AktifLM339DTBR2G Ringkasan
A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level result indicating which input is higher. The LM339 family combines four independent comparison channels in one package, reducing component count and simplifying board layout in threshold detection, sensor conditioning, level detection, memory, and control systems. Its open-collector outputs require an external pull-up resistor when a passive-high output is required.
Key features include a wide 3 V to 36 V supply operating range, a quad-comparator configuration, CMOS-compatible open-collector outputs, and TTL-compatible output behavior. The open-collector output structure can sink current from an output node while remaining electrically isolated from the supply rail, making the device useful in systems that use different logic voltage levels. The 14-pin TSSOP package supports automated surface-mount assembly and compact PCB layouts.
The LM339DTBR2G is intended for general-purpose comparison rather than precision voltage-reference use. Its four channels can be assigned to independent sensing or control functions, and the common supply architecture simplifies power distribution. Open-collector outputs allow several comparator outputs to share a pull-up node, provided the resulting sink-current and logic-level requirements are checked for the application.
Typical applications include automotive sensor interfaces, industrial control systems, consumer level detection, memory-device sensing, power-supply supervision, battery monitoring, and general threshold switching. The device is particularly useful when multiple analog quantities must be compared against independent thresholds or when the output must interface with a higher-voltage or open-drain bus.
When designing a board around the LM339DTBR2G, verify the comparator input common-mode range, output pull-up voltage, output sink current, and supply bypass requirements against the manufacturer datasheet. Place the input and supply-ground connections to minimize noise coupling, and use a suitable pull-up resistor on each output that must drive a logic input. Do not assume the open-collector output can source current without an external pull-up.
This product page combines the LM339DTBR2G package and ordering information with practical comparator-selection guidance, same-package alternatives, and design notes covering pull-up resistors, input common-mode limits, supply bypassing, and open-collector output behavior.
Pilihan pengganti yang segera untuk LM339DTBR2G — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera LM339DTBR2G (sama faktor bentuk dan kaki) — berbeza dalam Comparator Type, Output Type, Output Compatibility, Supply Configuration, Supply Voltage Range.
LM339PW
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM239PT
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
LM339PWG4
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LM339DTBR2G Penilaian maksimum & Ciri-ciri Elektrik
| Comparator Type | Quad differential comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | 3 V to 36 V |
| Supply Configuration | Single supply |
| Jenis Output | Open collector |
| Logic Compatibility | CMOS and TTL compatible |
| Operating Temperature Grade | Commercial temperature grade |
| Kemasan | 14-pin TSSOP |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin LM339DTBR2G 14-pin tssop
Konfigurasi pin untuk LM339DTBR2G (14-pin tssop pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk LM339DTBR2G.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
LM339DTBR2G patut untuk 6 aplikasis: Automotive Sensor Threshold Detection, Industrial Level Detection, Memory and Logic Control, Power Supply Supervision, Consumer Battery Monitoring, Open-Drain Interface and Wired-AND Control.
Automotive Sensor Threshold Detection
The LM339DTBR2G fits automotive and industrial sensor interfaces where several analog signals must be compared against independent thresholds. Its four open-collector channels can provide separate high, low, or over-range indications without requiring four separate packages. The 3 V to 36 V single-supply range supports systems using a common protected rail, while the TSSOP package helps reduce board area. Each open-collector output needs a pull-up matched to the receiving logic voltage. Because the input common-mode range and automotive qualification are product-specific, confirm both in the onsemi documentation before deploying the device in a safety-relevant or production automotive circuit.
Disebarkan
Industrial Level Detection
The LM339DTBR2G is suitable for industrial level and limit detection in tanks, machinery, and process equipment. Four comparator channels can monitor multiple sensor outputs or compare a sensed voltage against a reference threshold, providing open-collector status signals to PLC or relay-driver circuits. Its wide 3 V to 36 V supply capability is useful for industrial environments, while the open-collector outputs simplify interfacing to isolated or low-voltage logic when an external pull-up is fitted. Keep input and output routing separate from high-current switching paths, and verify the comparator's input common-mode limits for the exact sensor voltage range.
Disebarkan
Memory and Logic Control
The LM339DTBR2G can be used in memory-related sensing and logic-control circuits where a signal must be compared against a threshold and translated into an open-collector status. The four-channel arrangement allows compact implementation of multiple control decisions, while open-collector outputs permit wired-AND behavior with a shared pull-up. This is useful in legacy control logic and board-level supervision systems. Design the pull-up rail for the receiving logic, confirm that only one output drives the shared node low at a time, and provide local supply bypassing close to the device to reduce comparator noise and switching transients.
Disebarkan
Power Supply Supervision
The LM339DTBR2G can supervise multiple power rails by comparing divided supply voltages with reference thresholds and driving open-collector fault signals. The quad architecture provides independent positive and negative rail checks, overvoltage indication, or power-good signaling within one package. A pull-up allows the fault output to operate at the voltage expected by a supervisor, microcontroller, or system controller. Use resistor dividers with suitable tolerance and temperature characteristics, keep the comparator inputs away from switching-node noise, and check the minimum supply voltage needed for valid operation in the target power tree.
Disebarkan
Consumer Battery Monitoring
The LM339DTBR2G is appropriate for battery-powered products requiring simple voltage threshold indicators or charger-state decisions. Its four channels can monitor pack voltage, cell balance conditions, or charger status signals, while the 3 V to 36 V supply range accommodates protected battery-derived rails. Open-collector outputs can drive a pull-up to a low-energy system rail or communicate with a host controller. In a portable design, minimize leakage paths, select resistor dividers carefully for battery life, and keep the comparator supply current and operating range aligned with the product's battery budget.
Disebarkan
Open-Drain Interface and Wired-AND Control
The LM339DTBR2G is well suited to systems requiring an open-collector status bus rather than a push-pull logic output. Multiple comparator channels can share a pull-up node to create a wired-AND fault indication, allowing a supervisor to detect any asserted condition. This arrangement is useful in test equipment, control boards, and legacy industrial interfaces. Specify the maximum pull-up voltage, output sink current, and allowable total bus capacitance before assigning the node. Avoid simultaneous opposing drive conditions, provide a defined state during power-up, and route the shared node away from adjacent high-speed signals to minimize transient coupling.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LM339DTBR2G — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | LM339PW | LM239PT | LM339PWG4 |
|---|---|---|---|---|
| Package | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP |
| Brand | onsemi | Texas Instruments | STMicroelectronics | Texas Instruments |
| Comparator Channels | 4 | 4 | 4 | 4 |
| Output Type | Open collector | Open collector | Open collector | Open collector |
Penyeberangsung Jelas
- Four-channel integration in a 14-pin TSSOP (vsLM339PW)
- Open-collector output architecture (vsLM239PT)
- Wide single-supply operating range (vsLM339PWG4)
- Commercial-grade onsemi ordering option (vsLM239PT)
Catatan Desain
Use a dedicated pull-up resistor on every open-collector output that must drive a logic input. Select the pull-up rail from the receiving circuit's voltage domain, then check the comparator sink-current limit and the input current requirement. Keep the pull-up value high enough to preserve the required logic-low sink current and low enough to achieve the required rise time.
Place the device close to the signals it compares and route the input traces away from switching nodes, relay contacts, and high-current power paths. Keep the four comparator channels physically separated when their inputs switch at different rates, because shared ground impedance can move input thresholds. Follow the datasheet's recommended bypass-capacitor placement and provide a low-impedance return path.
Do not treat the open-collector output as a push-pull logic driver or use the supply voltage as an automatic output-high source. Verify that the pull-up voltage, input common-mode voltage, differential input voltage, and total supply range are valid at every operating condition. For wired-AND outputs, confirm that no two channels can sink the shared node simultaneously.
An open-collector output transitions high through the pull-up rather than an active driver, so its rising edge can be slow when the node has capacitance. Keep output traces short, minimize load capacitance, and avoid adding an excessive pull-up resistance. If a fast rising edge is required, verify the output timing and use a receiver with suitable input characteristics.
The comparator's normal dissipation is generally modest, but supply voltage, output sink current, and ambient temperature still affect junction temperature. Use the manufacturer thermal information for the TSSOP package and avoid placing the device beside a high-power regulator or heat source. Confirm the operating-temperature grade for the final assembly environment.
Maklumat Kesediaan
The product information identifies automotive and industrial applications but does not establish the exact orderable part's RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.