MAX202ECUE+T - 120kbps 5V RS-232 Transceiver | ADI
MPN: MAX202ECUE+T ✓ AktifMAX202ECUE+T Ringkasan
An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 bipolar voltage levels and converts received RS-232 signals back into CMOS-compatible logic. The MAX202E family satisfies EIA/TIA-232E and CCITT V.28 requirements, placing it within the hierarchy of interface transceivers, serial communication controllers, and broader industrial interface semiconductors.
Key features include two transmit channels, two receive channels, operation across a supply range tolerant of ±10% power-supply variation, and a maximum loaded data rate of 120 kbps. The on-chip charge pump generates the positive and negative voltage levels required by RS-232 drivers, eliminating external charge-pump capacitors. Its 16-pin TSSOP body is suitable for compact surface-mount assemblies, while the integrated ESD protection improves resilience in industrial cabinets and systems with long external cables.
The MAX202E uses complementary driver and receiver stages to interface with a UART, microcontroller, or other CMOS logic device. Driver outputs swing to positive and negative RS-232 levels, while receiver inputs translate the bipolar signal into a valid logic-high or logic-low output. Because RS-232 is a point-to-point, unbalanced interface, each channel is normally routed through dedicated signal and return conductors rather than a multi-drop bus.
Typical applications include industrial serial consoles, barcode and label scanners, test and measurement equipment, programmable-logic-controller service ports, medical-instrument diagnostic interfaces, and embedded control systems that retain a legacy RS-232 connector. The device is especially useful where 120 kbps performance and ESD resilience are more important than the smaller footprint of a modern differential transceiver.
When laying out the PCB, keep the transceiver close to the connector and route driver outputs and receiver inputs away from clocks, switching regulators, and high-current traces. Confirm the board’s RS-232 connector pinout, grounding strategy, and protection-network requirements before applying the device to a new system.
This page combines package, electrical, interface, and application information with drop-in alternatives and practical PCB guidance. It is designed to help engineers identify whether the MAX202ECUE+T fits a 5 V RS-232 design and how it compares with pin-compatible MAX202E variants.
Pilihan pengganti yang segera untuk MAX202ECUE+T — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MAX202ECUE+T (sama faktor bentuk dan kaki) — berbeza dalam ESD Protection, Charge Pump, Product Type, Interface Standard, Supply Voltage.
MAX202EEUE+T
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX202CPWR
✅ Masuk Drop-In✓ Ada di Stok
$0.9023 / Unit
Lihat Datasheet →MAX202ECUE+T Spesifikasi
| Product Type | Dual RS-232 transceiver with 2 drivers and 2 receivers |
| Number of Drivers | 2 channels |
| Number of Receivers | 2 channels |
| Tegangan Pemberi Arus | 5 V nominal, tolerant of ±10% supply variation |
| Maximum Data Rate | 120 kbps when loaded |
| Interface Standard | EIA/TIA-232E and CCITT V.28 |
| ESD Protection | ±15 kV human body model |
| Charge Pump | Integrated, no external charge-pump capacitors required |
| Logic Compatibility | CMOS UART logic |
| Kemasan | 16-pin TSSOP |
| Jenis Pemasangan | Surface mount |
Konfigurasi Pin MAX202ECUE+T
| Pin 1 | VCC — Positive supply-voltage connection |
| Pin 2 | R1OUT — Receiver 1 logic output |
| Pin 3 | R2OUT — Receiver 2 logic output |
| Pin 4 | R2IN — Receiver 2 RS-232 input |
| Pin 5 | R1IN — Receiver 1 RS-232 input |
| Pin 6 | GND — Ground connection |
| Pin 7 | T1OUT — Transmitter 1 RS-232 output |
| Pin 8 | T2OUT — Transmitter 2 RS-232 output |
| Pin 9 | T2IN — Transmitter 2 logic input |
| Pin 10 | T1IN — Transmitter 1 logic input |
| Pin 11 | GND — Ground connection |
| Pin 12 | GND — Ground connection |
| Pin 13 | VCC — Positive supply-voltage connection |
| Pin 14 | V+ — Charge-pump positive voltage storage node |
| Pin 15 | GND — Ground connection |
| Pin 16 | VCC — Positive supply-voltage connection |
Aplikasi Biasa
MAX202ECUE+T patut untuk 6 aplikasis: Industrial Serial Control Console, Barcode and Label Scanner Interface, Test and Measurement Instrument, Embedded Controller Service Port, Medical Instrument Diagnostic Interface, Programmable Logic Controller Communication.
Industrial Serial Control Console
The MAX202ECUE+T fits a legacy RS-232 service console that must communicate with a controller or data-acquisition unit over a wired link. Its two transmitters and two receivers support both command and response paths, while the 120 kbps maximum data rate is suitable for configuration menus, diagnostic logs, and short data exchanges. The integrated charge pump eliminates external pumping capacitors, simplifying a compact industrial controller. Place the device near the DB9 or equivalent connector, maintain a low-impedance ground reference, and verify that the selected connector wiring matches the receiver and driver assignments in the MAX202E pin-description table.
Disebarkan
Barcode and Label Scanner Interface
The MAX202ECUE+T can serve as the electrical interface between an embedded controller and a barcode or label scanner that retains an RS-232 output. The 120 kbps capability provides ample margin for scanner data bursts, while the ±15 kV human-body-model ESD rating adds protection for a connector exposed to routine operator contact. Because the transceiver operates from one nominal 5 V rail, it fits compact scanner-control boards with limited supply capacity. Route the two receiver channels toward the scanner inputs and the driver channels toward the connector, and keep external switching regulators and relay traces away from the signal path.
Disebarkan
Test and Measurement Instrument
Instrumentation systems often retain an RS-232 port for calibration utilities, remote commands, and logged measurement data. The MAX202ECUE+T provides two full-duplex-compatible RS-232 channels, 120 kbps operation, and standards conformance to EIA/TIA-232E and CCITT V.28, making it appropriate for a laboratory front panel or remote test head. Its integrated charge pump avoids external pump components and leaves more board area for analog or precision circuitry. Keep the interface section separated from high-impedance measurement nodes, and provide a stable ground plane so receiver thresholds remain reliable under laboratory load transients.
Disebarkan
Embedded Controller Service Port
A microcontroller-based product can use the MAX202ECUE+T to add a wired service or configuration port without implementing RS-232 level conversion in discrete components. The device interfaces directly with CMOS UART logic while presenting the bipolar voltage swings required by the RS-232 standard. Its 16-pin TSSOP package suits compact controller boards, and the 120 kbps rate is more than adequate for firmware download functions, diagnostic commands, and configuration scripts. Follow the datasheet’s recommended decoupling, route the serial lines away from switching nodes, and verify the host computer’s TXD-to-RXD and ground wiring before deployment.
Disebarkan
Medical Instrument Diagnostic Interface
The MAX202ECUE+T can support a service-only RS-232 diagnostic connection in medical equipment where the main clinical interface uses another protocol. Its 120 kbps data rate is suitable for maintenance logs, self-test reports, and configuration transfer, while ±15 kV human-body-model ESD protection strengthens the external connector interface. The single 5 V supply operation and integrated charge pump reduce the component count beside the main controller. Confirm the required operating-temperature grade, isolation strategy, and regulatory architecture for the complete medical product, and do not treat the transceiver’s ESD rating as a substitute for the required isolation barrier.
Disebarkan
Programmable Logic Controller Communication
The MAX202ECUE+T is suitable for an RS-232 communication link between a programmable logic controller or embedded automation module and an external operator terminal. The dual transmitter and dual receiver arrangement supports bidirectional command and status traffic, while 120 kbps capability provides sufficient bandwidth for short control packets and diagnostic sequences. The 16-pin TSSOP package is compact, and the integrated charge pump simplifies single-rail power design. For reliable industrial operation, use the manufacturer’s recommended bypass capacitors, maintain a low-impedance ground connection to the connector shell where applicable, and verify the PLC’s RS-232 electrical specification and handshaking requirements.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MAX202ECUE+T — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MAX202EEUE+T | MAX202CPWR |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Transceiver Configuration | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Maximum Data Rate | 120 kbps | 120 kbps | 120 kbps |
| Nominal Supply Voltage | 5 V | 5 V | 5 V |
| Interface Compliance | EIA/TIA-232E and CCITT V.28 | EIA/TIA-232E and CCITT V.28 | RS-232 and V.28 interface family |
| Charge Pump | Integrated | Integrated | Integrated charge-pump circuitry |
Penyeberangsung Jelas
- Maintains the same 16-pin TSSOP interface while offering documented suffix-grade alternatives (vsMAX202EEUE+T)
- Closely matched MAX202C drop-in with published compatibility information (vsMAX202CPWR)
- Single-supply operation with integrated level-shift generation (vsMAX202CPWR)
- Adds interface-level ESD resilience for connector-based equipment (vsMAX202EEUE+T)
Catatan Desain
Place the MAX202ECUE+T close to the RS-232 connector so driver outputs and receiver inputs remain short. Keep switching-regulator nodes, clock edges, and high-current return paths outside the interface area. Provide a continuous ground plane beneath the device and route connector returns directly to the interface ground reference. This arrangement reduces receiver sensitivity to external cable transients and helps prevent driver currents from disturbing nearby logic.
Decouple the device at its VCC pins with the capacitance and placement specified in the MAX202E datasheet. The integrated charge pump generates the bipolar RS-232 output levels from the 5 V rail, but local supply decoupling remains essential because driver transitions can produce fast current pulses. Keep the charge-pump nodes and bypass connection compact, and avoid routing those traces between or beneath unrelated high-speed signals.
Do not treat the MAX202ECUE+T as an RS-485 device: its driver outputs are bipolar RS-232 levels intended for point-to-point links. Confirm TXD-to-RXD wiring, signal polarity, and connector pin assignments for both ends of the cable. When substituting MAX202EEUE+T or MAX202CPWR, verify the ordering suffix, temperature grade, ESD rating, and supply limits because the package match alone does not establish full application equivalence.
RS-232 driver outputs carry high-voltage transitions even though the logic-side data rate is moderate. Keep the two driver traces away from receiver inputs and sensitive analog circuits, and avoid long parallel runs with power or clock traces. If the cable leaves the enclosure, place the transceiver near the connector so conducted and radiated disturbances are confined to the protected interface section rather than spreading across the PCB.
Maklumat Kesediaan
The manufacturer materials describe the MAX202E as a current RS-232 transceiver family. RoHS, REACH, halogen-free, and conflict-minerals statements were not confirmed for this exact ordering code and therefore remain unknown.