Analog Devices

MAX3232EWE+T - 1Mbps RS-232 Transceiver | Analog Devices

MPN: MAX3232EWE+T ✓ Aktif
3.0 V to 5.5 V Vdss Down to 10 nA Id 16-SOIC Package
MOQ: 1 |

MAX3232EWE+T Ringkasan

The Analog Devices MAX3232EWE+T is a 3.0 V to 5.5 V, low-power, true RS-232 transceiver with two drivers and two receivers, supporting data rates up to 1 Mbps in a 16-SOIC package. It provides plus or minus 15 kV ESD protection on the serial-port connection pins and operates from four 0.1 uF charge-pump capacitors.

A true RS-232 transceiver converts logic-level signals from a UART, microcontroller, or host into balanced, bipolar serial-port levels, then converts incoming serial signals back into CMOS-compatible logic. Within the interface hierarchy, the MAX3232E is a full-duplex RS-232 transceiver, a line-driver and line-receiver circuit, and a serial interface IC commonly used for legacy serial ports, industrial equipment, and embedded control links.

Key features include a 3.0 V minimum supply voltage, a 5.5 V maximum supply voltage, and an operating data rate of up to 1 Mbps. The MAX3232E adds plus or minus 15 kV ESD protection, while its low-power design supports shutdown and reduced-power operating modes for portable or space-constrained equipment. Four external 0.1 uF capacitors allow the on-chip charge pump to generate the positive and negative voltages required by true RS-232 drivers.

Internally, the device combines two line drivers, two line receivers, and a dual charge-pump circuit. The charge-pump architecture supports operation from a single 3.0 V to 5.5 V supply instead of a plus or minus voltage source. This simplifies board design, although external capacitor placement and connector-side transient protection remain essential for reliable serial links in industrial environments.

Typical applications include RS-232 connections to test and measurement equipment, database controllers, modems, point-of-sale terminals, industrial control panels, and legacy service-port interfaces. The 1 Mbps capability is useful for short, point-to-point links where legacy software expects standard RS-232 signaling, while the 16-SOIC package simplifies assembly on through-hole-compatible boards.

When laying out this transceiver, place the four 0.1 uF charge-pump capacitors close to their designated pins and route connector-side signals away from sensitive logic. Keep the interface ground reference close to the connector ground and confirm that the host UART voltage levels match the MAX3232E logic supply.

This page organizes the MAX3232EWE+T specifications, package details, drop-in alternatives, application guidance, and design notes into a single engineering reference for RS-232 interface design and sourcing decisions.

Pilihan pengganti yang segera untuk MAX3232EWE+T — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera MAX3232EWE+T (sama faktor bentuk dan kaki) — berbeza dalam Package, Charge-Pump Architecture, Maximum Data Rate, Supply Voltage Range, ESD Protection.

Texas Instruments
Package: 16-SOIC, 7.50 mm width
Maximum Data Rate: 250 kbit/s
Supply Voltage Range: 3 V to 5.5 V
Bandingkan Dengan MAX3232EWE+T →
Maxim Integrated
Package: 16-SOIC (NSOIC, 0.150 inch)
Bandingkan Dengan MAX3232EWE+T →
Analog Devices
Charge-Pump Architecture: Dual
Bandingkan Dengan MAX3232EWE+T →
Texas Instruments
Package: 16-pin SOIC (DW), 5.30 mm body width
Charge-Pump Architecture: Dual charge-pump circuit
Maximum Data Rate: 250 kbit/s
Bandingkan Dengan MAX3232EWE+T →

MAX3232EWE+

✅ Masuk Drop-In
📦 16-SOIC
Same MAX3232E electrical configuration and 16-SOIC footprint; the orderable packaging designation differs by the +T tape-and-reel suffix

📋 Alternatif rujukan (tidak dalam katalog)

MAX3232CDW

✅ Masuk Drop-In
Texas Instruments
📦 16-SOIC
Dual RS-232 line driver/receiver transceiver · 2 · 2 · 3 V to 5.5 V · 250 kbit/s · 300 µA · 5 V logic · 0.1 µF

Hubungi untuk harga

Lihat Datasheet →

MAX3232CWE+

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
Analog Devices
📦 16-SOIC
Dual RS-232 transceiver · 2 · 2 · 3.0 V to 5.5 V · 1 Mbps · RS-232 · 16-pin SOIC · Surface Mount

Hubungi untuk harga

Lihat Datasheet →

MAX3232EUE+T

✅ Masuk Drop-In
Analog Devices
📦 16-SOIC
2/2 RS-232 transceiver · 2 · 2 · 3.0 V to 5.5 V · 1 Mbps · 300 µA · 0.1 µF each · 4

Hubungi untuk harga

Lihat Datasheet →

MAX3232ESE+T

✅ Masuk Drop-In
Maxim Integrated
📦 16-SOIC
RS-232 Transceiver (2 drivers / 2 receivers) · RS-232 (EIA/TIA-232) · 1 Mbps · 3.0 V to 5.5 V · 1 mA typical · 2 · 2 · +/-15 kV HBM

Hubungi untuk harga

Lihat Datasheet →

MAX3232EWE+T Spesifikasi

Product Type True RS-232 transceiver
Number of Drivers 2
Number of Receivers 2
Supply Voltage Range 3.0 V to 5.5 V
Maximum Data Rate 1 Mbps
ESD Protection +/-15 kV on serial-port connection pins
Low-Power Shutdown Current Down to 10 nA
Charge-Pump Capacitors 4 x 0.1 uF
Charge-Pump Architecture Dual on-chip charge pump
Kemasan 16-SOIC
Kiraan Pin 16 pins
Jenis Pemasangan Surface mount
Signal Standard TIA/EIA-232-F / true RS-232
Production Status Production

Panduan Konfigurasi Pin MAX3232EWE+T 16-soic

Konfigurasi pin untuk MAX3232EWE+T (16-soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 16-soic untuk MAX3232EWE+T

Tiada data garisan pin yang diperoleh untuk MAX3232EWE+T.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

MAX3232EWE+T patut untuk 6 aplikasis: Industrial Controller RS-232 Port, Test and Measurement Equipment, Database and Legacy Service Interfaces, Point-of-Sale and Retail Terminals, Embedded UART-to-RS-232 Bridges, Portable and Service Diagnostic Equipment.

🏭

Industrial Controller RS-232 Port

The MAX3232EWE+T fits industrial controller boards that must communicate with legacy RS-232 equipment through a DB9 connector. Its two-driver, two-receiver arrangement supports full-duplex links, while the 3.0 V to 5.5 V supply range allows operation from a 3.3 V system rail. The documented up-to-1-Mbps capability supports short service links, and plus or minus 15 kV ESD protection strengthens the connector-facing pins. Route the four 0.1 uF charge-pump capacitors exactly as shown in the pin-configuration table.

🔧

Test and Measurement Equipment

The MAX3232EWE+T provides a practical single-supply RS-232 interface for oscilloscopes, bench instruments, and laboratory controllers that retain serial-port connectors. Two drivers and two receivers support bidirectional command and response traffic, while the true RS-232 charge pump generates the bipolar voltage levels expected by older equipment. The 1 Mbps rate provides margin for short direct connections, and the low-power shutdown mode helps reduce standby consumption in portable test setups.

🖥️

Database and Legacy Service Interfaces

The MAX3232EWE+T is suited to controllers, adapters, and service equipment that connect to legacy DB9 RS-232 ports. Because the transceiver operates from a single 3.0 V to 5.5 V supply, it avoids the negative rail and discrete charge-pump circuitry once associated with older RS-232 designs. The plus or minus 15 kV ESD rating on serial-port pins provides useful connector-side protection. For cables leaving an enclosure, still add coordinated surge protection and a low-impedance chassis-ground path.

🛒

Point-of-Sale and Retail Terminals

Point-of-sale terminals, receipt printers, scanners, and payment peripherals can use the MAX3232EWE+T where their host interface requires true RS-232 rather than USB or a differential bus. The 2/2 driver-receiver configuration supports bidirectional service traffic on one connector, and the 16-SOIC package is practical for medium-density control boards. The 1 Mbps maximum rate covers short service connections, while the low-power shutdown current down to 10 nA helps when the terminal spends substantial time idle.

🔌

Embedded UART-to-RS-232 Bridges

The MAX3232EWE+T bridges a microcontroller UART to a true RS-232 port without requiring a separate negative power rail. Its 3.0 V minimum supply voltage suits 3.3 V embedded systems, and the dual charge pump plus four external 0.1 uF capacitors keeps the interface compact. The 1 Mbps capability covers short diagnostic and configuration links. Confirm UART logic thresholds, connect the transceiver ground reference to the equipment ground, and keep charge-pump routing away from sensitive analog sections.

📱

Portable and Service Diagnostic Equipment

Handheld service tools and portable diagnostic devices benefit from the MAX3232EWE+T because it provides true RS-232 signaling from a 3.0 V to 5.5 V supply without a negative rail. The low-power design and shutdown current down to 10 nA reduce the burden on battery-powered systems when the serial interface is inactive. The up-to-1-Mbps rate allows short local connections to equipment consoles, while plus or minus 15 kV ESD protection helps manage electrostatic discharge encountered during field servicing.

What is the MAX3232EWE+T and what does it do?
The MAX3232EWE+T is a true RS-232 transceiver that combines two line drivers, two line receivers, and a dual charge-pump circuit in a 16-SOIC package. According to the Analog Devices MAX3232E product page, it operates from 3.0 V to 5.5 V, supports data rates up to 1 Mbps, and provides plus or minus 15 kV ESD protection. It converts UART logic levels to and from bipolar RS-232 signals.
What are the key specifications of MAX3232EWE+T that engineers should know?
The MAX3232EWE+T provides two drivers, two receivers, a 3.0 V to 5.5 V supply range, and data rates up to 1 Mbps. Analog Devices specifies plus or minus 15 kV ESD protection on the serial-port pins and a shutdown current down to 10 nA. The true RS-232 implementation needs four external 0.1 uF charge-pump capacitors and is packaged in a 16-SOIC.
What is the difference between MAX3232EWE+T and MAX3232EWE+?
The MAX3232EWE+T and MAX3232EWE+ use the same MAX3232E device and 16-SOIC electrical configuration; the plus-T notation identifies the tape-and-reel ordering option. The manufacturer lists both as 2/2 full RS-232 transceivers operating from 3.0 V to 5.5 V at up to 1 Mbps. For new tape-and-reel production, MAX3232EWE+T is the designated orderable variant.
Does the MAX3232EWE+T need external charge-pump capacitors?
Yes, the MAX3232EWE+T requires four external 0.1 uF capacitors for its dual charge-pump circuit. These capacitors generate the positive and negative internal rail voltages required by true RS-232 drivers from a single 3.0 V to 5.5 V supply. Place each capacitor close to its designated IC pin and follow the pin-configuration table in the manufacturer datasheet when assigning the PCB footprint.
What is the maximum data rate of the MAX3232EWE+T?
The MAX3232EWE+T supports RS-232 data rates up to 1 Mbps. Analog Devices describes the MAX3232E as a low-power true RS-232 transceiver for 3.0 V to 5.5 V operation. The 1 Mbps rate suits short direct connections between a UART-equipped controller and RS-232 equipment, although cable length, loading, and system timing can limit practical throughput.
Is the MAX3232EWE+T compatible with 3.3 V microcontrollers?
Yes, the MAX3232EWE+T operates from a 3.0 V to 5.5 V supply, so it can be powered at 3.3 V alongside a compatible 3.3 V UART or microcontroller. Confirm that the connected logic pins meet the MAX3232E input and output thresholds and that the host UART is 3.3 V rather than 5 V. A level translator is required if the host uses 5 V TTL levels.
Where can I download the MAX3232EWE+T datasheet PDF?
Download the MAX3232EWE+T documentation from the Analog Devices MAX3232E product page at https://www.analog.com/en/products/max3232e.html. The manufacturer page provides the MAX3232E data sheet and product resources. The +T suffix identifies the tape-and-reel packaging option, while the electrical and pin configuration are documented under the MAX3232E family.
Where can I find the MAX3232EWE+T pinout?
The MAX3232EWE+T pinout is documented in the pin-configuration table of the Analog Devices MAX3232E data sheet linked from the manufacturer product page. The package is a 16-SOIC with four designated charge-pump capacitor pins, two driver outputs, two receiver inputs, and supply and ground connections. Use that table when assigning nets and confirming the PCB land pattern.
What is the best drop-in replacement for MAX3232EWE+T?
The closest same-family drop-in options are the MAX3232EWE+ in the same 16-SOIC electrical configuration and the wide-SOIC MAX3232CDW, which an independent comparison identifies as functionally equivalent for most designs. Verify the exact package width, charge-pump capacitor pins, and ESD rating before substitution. Request a formal cross-reference review when the design requires identical production sourcing.
Can MAX3232CDW replace MAX3232EWE+T in an existing PCB?
MAX3232CDW can serve as a functional alternative when its 16-SOIC land pattern matches the MAX3232EWE+T footprint and its capacitor and interface pins align correctly. The available component comparison reports no measurable differences in primary technical parameters and considers the devices functionally equivalent for most designs. A final manufacturer-datasheet check remains necessary before a production substitution.
When should I choose MAX3232EWE+T instead of MAX3232CDW?
Choose MAX3232EWE+T when plus or minus 15 kV ESD protection, a documented low-power shutdown current down to 10 nA, and the established MAX3232E family are the primary requirements. Choose MAX3232CDW when its price, sourcing, or lead time is more attractive and your design can tolerate the differences identified in the device documentation. Both are intended for true RS-232 interface duties.
Is MAX3232EWE+T suitable for industrial serial-port equipment?
Yes, MAX3232EWE+T is suitable for industrial RS-232 interfaces when its supply, data-rate, package, and ESD requirements match the equipment specification. Its plus or minus 15 kV pin protection strengthens the interface against electrostatic discharge, while the 1 Mbps capability supports short direct links. Add external surge protection and proper grounding for cables leaving an enclosure.
Where to buy MAX3232EWE+T online?
Use the Request a Quote form on this page to request the current price, stock position, minimum order quantity, and lead time for MAX3232EWE+T. The exact quantity-break pricing and current inventory are handled through the quote workflow so that the commercial response reflects current sourcing conditions. Identify the tape-and-reel requirement and target quantities in the request.
What is the price of MAX3232EWE+T?
Current pricing for MAX3232EWE+T is obtained through the Request a Quote form on this page. Pricing varies with order quantity, packaging format, and current component supply, so the live quote is the authoritative commercial figure. Include the required reel quantity and annual usage so the quotation can be matched to the appropriate production tier.
What is the lead time and stock status of MAX3232EWE+T?
Submit a Request a Quote through this page to confirm the current stock status, minimum order quantity, and lead time for MAX3232EWE+T. The MAX3232E is identified by Analog Devices as being in production, but orderable quantity and delivery timing can vary with packaging and demand. A quotation response provides the current allocation and scheduled shipment information.

Data referensi kejuruteraan untuk MAX3232EWE+T — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the MAX3232EWE+T for a new 16-SOIC design that requires two drivers, two receivers, true bipolar RS-232 operation, and up to 1 Mbps communication from a 3.0 V to 5.5 V supply. Its plus or minus 15 kV ESD protection and shutdown current down to 10 nA are useful in field-service and portable systems. MAX3232EWE+ provides the same MAX3232E electrical configuration when a different orderable packaging designation is appropriate. MAX3232CDW is a practical same-family functional alternative when availability or sourcing is more important, but verify its package dimensions, ESD specification, and capacitor pin assignments. MAX3232CWE+ shares the family architecture but requires an explicit datasheet comparison. Use MAX3221IPWR instead when only one driver and one receiver are needed and reduced channel count is acceptable. Always confirm the exact 16-SOIC body width and land pattern against the manufacturer pin-configuration table before releasing a substitution.

Perbandingan dengan Gantian

Parametr Produk Ini MAX3232EWE+ MAX3232CDW MAX3232CWE+ MAX3232EUE+T MAX3232ESE+T
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Transceiver Configuration 2/2 full RS-232 2/2 full RS-232 2/2 full RS-232 2/2 full RS-232 2/2 full RS-232 2/2 full RS-232
Supply Voltage Range 3.0 V to 5.5 V 3.0 V to 5.5 V 3.0 V to 5.5 V 3.0 V to 5.5 V 3.0 V to 5.5 V 3.0 V to 5.5 V
Maximum Data Rate 1 Mbps 1 Mbps 1 Mbps 1 Mbps 1 Mbps 1 Mbps
Number of Drivers and Receivers 2 drivers, 2 receivers 2 drivers, 2 receivers 2 drivers, 2 receivers 2 drivers, 2 receivers 2 drivers, 2 receivers 2 drivers, 2 receivers

Penyeberangsung Jelas

  • Documented high-level ESD protection on serial-port pins (vsMAX3232CDW)
  • Very low shutdown current for power-managed interfaces (vsMAX3232CDW)
  • Full-duplex interface in a widely used 16-SOIC format (vsMAX3221IPWR)
  • Single-supply true RS-232 operation with a 1 Mbps ceiling (vsMAX3232ESE+T)

Catatan Desain

Place the four required 0.1 uF charge-pump capacitors directly beside their corresponding MAX3232EWE+T pins and keep the associated traces short. Use the manufacturer pin-configuration table to confirm capacitor orientation and connection. Keep switching charge-pump nodes away from receiver inputs and sensitive analog circuitry to minimize radiated and coupled noise on the serial interface.

Do not treat the MAX3232EWE+T as a 5 V TTL transceiver; it generates true bipolar RS-232 levels through its charge pump. Verify that the host UART uses compatible logic levels, connect the interface ground to the equipment ground, and install the four 0.1 uF capacitors. A missing or incorrectly valued charge-pump capacitor can prevent negative-voltage generation and cause communication failures.

For connector-side cables, route TXD and RXD traces away from clocks, switching regulators, and sensitive analog inputs. Maintain a continuous interface-ground reference between the transceiver and connector ground. The plus or minus 15 kV ESD rating is a component-level protection feature, but board layout, chassis grounding, and coordinated external surge protection remain necessary for cables exposed to industrial transients.

Decouple the MAX3232EWE+T supply at the device with local high-frequency and bulk capacitance, following the manufacturer layout guidance. The 3.0 V to 5.5 V operating range permits a 3.3 V system rail, but confirm UART logic thresholds before connecting. When shutdown current down to 10 nA is important, drive the shutdown control correctly and account for leakage from the external capacitor network.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The Analog Devices product page identifies the MAX3232E family as being in production. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not confirmed in the retrieved product information.

Pencarian Berhubungan

MAX3232EWE+T datasheet MAX3232EWE+T pinout MAX3232EWE+T price MAX3232EWE+T equivalent MAX3232EWE+T replacement MAX3232EWE+T 16 SOIC MAX3232EWE+T RS-232 transceiver Analog Devices MAX3232EWE+T MAX3232EWE+T vs MAX3232CDW MAX3232EWE+T application circuit MAX3232E 1Mbps RS-232 IC MAX3232EWE+T ESD protection

Komponen dan Tanda berkaitan

Analog Devices MAX3232EWE+T MAX3232E MAX3232EWE+ MAX3232CDW MAX3232CWE+ MAX3232EUE+T MAX3232ESE+T MAX3221IPWR RS-232 true RS-232 transceiver line driver line receiver charge-pump circuit UART TIA/EIA-232-F ESD protection 3.0 V to 5.5 V supply 1 Mbps data rate 16-SOIC surface mount industrial control DB9 serial port external surge protection
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ