MAX485EESA+T - 2.5Mbps RS-485 Transceiver | Analog Devices
MPN: MAX485EESA+T ✓ AktifMAX485EESA+T Ringkasan
A transceiver IC combines a differential line driver and receiver on one die, allowing a digital UART signal to travel over a balanced, noise-resistant bus. The MAX485 family belongs to the interface IC hierarchy: RS-485 transceiver → differential transceiver → wired-communication interface IC → semiconductor. Its half-duplex architecture supports bidirectional communication by sharing one differential pair and changing direction through the driver-enable and receiver-enable controls.
The MAX485EESA+T combines a 4.75 V to 5.25 V supply range with a 2.5 Mbps maximum data rate. Its slew-rate-limited driver reduces unwanted high-frequency energy on the bus, while ±15 kV ESD protection strengthens the interface against electrostatic discharge encountered in industrial environments. The low-power design also supports systems where the transceiver must remain connected to a 5 V control rail.
Operationally, the device provides separate receive-enable and driver-enable inputs, allowing the receiver to remain active while transmission is disabled. The receiver converts differential bus voltage into a logic-level output, while the driver converts a logic-level input into differential A and B outputs. This arrangement supports both point-to-point links and multi-drop RS-485 networks when termination and biasing are designed correctly.
Typical applications include industrial control networks, building automation, instrumentation links, data acquisition systems, motor controllers, and factory communication equipment. The MAX485EESA+T is especially appropriate for factory environments where ESD exposure, long cable runs, and grounded or ungrounded equipment can create substantial bus-level transients.
PCB design should preserve the pinout and provide the decoupling, protection, and termination required by the bus. Place the VCC bypass capacitor close to the supply pin, route the differential pair as a balanced pair, and use a protection network designed for the expected surge and ESD environment. Avoid long unprotected stubs because they can create impedance discontinuities and reflections.
This product page combines the manufacturer-datasheet specifications, verified package and cross-reference information, drop-in alternatives, and application-focused engineering guidance. It is structured to support component selection, PCB replacement planning, and RS-485 interface design rather than only basic part identification.
Pilihan pengganti yang segera untuk MAX485EESA+T — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MAX485EESA+T (sama faktor bentuk dan kaki) — berbeza dalam Package, Product Type, Supply Voltage Range, Maximum Data Rate, Transceiver Configuration.
ADM485JNZ
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX485ESA+T
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX485ECSA+T
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
SP485EEN-L/TR
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →SN65HVD05D
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX485EESA+T Spesifikasi
| Product Type | Half-duplex RS-485/RS-422 transceiver |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Nominal Supply Voltage | 5 V |
| Maximum Data Rate | 2.5 Mbps |
| Driver Output Type | Slew-rate-limited differential driver |
| Receiver Output Type | Differential logic-level receiver |
| ESD Protection | ±15 kV |
| Communication Mode | Half-duplex |
| Supported Standards | RS-485 and RS-422 |
| Kemasan | 8-pin NSOIC/SOIC |
| Jenis Pemasangan | Surface mount |
| Gambaran Suhu Operasi | -40 °C to +85 °C |
| Driver and Receiver Count | 1 driver and 1 receiver |
| Power Classification | Low-power transceiver |
Konfigurasi Pin MAX485EESA+T
| Pin 1 | RO — Receiver output |
| Pin 2 | /RE — Active-low receiver enable |
| Pin 3 | DE — Driver enable |
| Pin 4 | DI — Driver input |
| Pin 5 | GND — Ground |
| Pin 6 | A — Non-inverting differential bus terminal |
| Pin 7 | B — Inverting differential bus terminal |
| Pin 8 | VCC — Positive supply voltage |
Aplikasi Biasa
MAX485EESA+T patut untuk 6 aplikasis: Industrial RS-485 Control Networks, Building Automation and HVAC Equipment, Data Acquisition and Instrumentation, Motor Controller and Actuator Links, Security and Access-Control Networks, Test and Measurement Equipment.
Industrial RS-485 Control Networks
The MAX485EESA+T fits industrial control networks that distribute commands between a controller and remote actuators over a balanced RS-485 bus. Its 2.5 Mbps maximum data rate supports responsive communication, while the slew-rate-limited driver reduces high-frequency energy on long factory cables. The ±15 kV ESD rating adds useful protection when field wiring is exposed to electrostatic discharge. Designers should verify the transceiver enable sequencing, install termination only at physical bus ends, and use biasing appropriate for the number of idle receivers on the network.
Disebarkan
Building Automation and HVAC Equipment
The MAX485EESA+T is appropriate for building automation controllers, HVAC units, and environmental monitors that use a 5 V RS-485 backbone. Half-duplex operation allows the same differential pair to carry outbound commands and inbound sensor responses, reducing wiring complexity compared with separate full-duplex links. Its 4.75 V to 5.25 V supply range aligns with common 5 V controller hardware, and the 2.5 Mbps rate leaves ample throughput for configuration and status traffic. The board layout should keep the bus pair impedance-controlled and isolate long building runs with appropriate surge protection.
Disebarkan
Data Acquisition and Instrumentation
The MAX485EESA+T can connect laboratory and process instrumentation to a central data-acquisition system through a half-duplex RS-485 bus. The differential receiver rejects common-mode noise that could otherwise affect a single-ended measurement interface, and the 2.5 Mbps capability permits compact and repeatable polling of multiple sensors. The 5 V operating range suits embedded acquisition hardware. For reliable instrumentation performance, use twisted shielded cabling, provide a defined reference or isolated system design, and place bus termination away from active driver outputs.
Disebarkan
Motor Controller and Actuator Links
The MAX485EESA+T fits motor controllers, remote actuators, and industrial drive modules that exchange commands and status over RS-485. Its half-duplex architecture efficiently uses one A/B pair for bidirectional traffic, while 2.5 Mbps is substantially faster than required for many control loops. The extended -40 °C to +85 °C operating range supports equipment exposed to temperature variation. Designers should prevent motor-generated transients from reaching the transceiver by using appropriate isolation or protection, and should confirm that cable routing avoids parallel power conductors.
Disebarkan
Security and Access-Control Networks
The MAX485EESA+T can support access-control readers, door controllers, alarm panels, and other security equipment connected through an RS-485 backbone. The half-duplex interface reduces the number of conductors required for command polling and device responses, while the ±15 kV ESD protection is valuable around frequently serviced field equipment. Its 2.5 Mbps rate supports deterministic polling of multiple nodes. Security installations should include surge and ground-fault mitigation, controlled cable routing, and firmware-based authentication because the physical bus alone does not provide cryptographic protection.
Disebarkan
Test and Measurement Equipment
The MAX485EESA+T is useful in test systems and bench instruments that exchange commands with remote fixtures over RS-485. The differential interface provides a robust communications path in laboratories containing motors, switching supplies, and other noise sources, while the 2.5 Mbps limit supports responsive test sequencing. The 5 V supply requirement integrates directly into many embedded controller boards. For instrumentation-grade reliability, use a controlled common-mode reference, provide a high-impedance bias network, and validate the complete bus with target cable lengths and termination arrangements.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MAX485EESA+T — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | ADM485JNZ | MAX485ESA+T | MAX485ECSA+T | SP485EEN-L/TR | SN65HVD05D |
|---|---|---|---|---|---|---|
| Package | 8-pin NSOIC/SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | MaxLinear | Texas Instruments |
| Supported Interfaces | RS-485 and RS-422 | RS-485 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 | RS-485 |
Penyeberangsung Jelas
- Retains the full 2.5 Mbps signaling rate (vsMAX485ESA+T)
- Extended-temperature coverage (vsMAX485ECSA+T)
- Documented pin-compatible second source (vsSP485EEN-L/TR)
Catatan Desain
Place the transceiver's VCC bypass capacitor directly beside pin 8 and the ground connection beside pin 5. Keep the A and B traces as a tightly coupled differential pair, maintain continuous reference-plane return beneath the pair, and avoid routing the bus alongside switching-power or motor-current paths. Shorten stub branches to minimize reflected impedance on the cable.
Do not allow multiple drivers to assert the bus simultaneously. The MAX485EESA+T supports half-duplex communication, so its DE and active-low /RE controls must be sequenced to avoid driver contention. Use fail-safe biasing so the bus has a defined idle state, and confirm that the UART is not transmitting when direction changes from receive to transmit.
Install termination only at the two physical ends of the main RS-485 cable, not at every node. Select the resistor value and cable impedance according to the manufacturer application guidance, and account for bias resistors so that multiple idle receivers do not excessively load the network. Additional TVS or surge protection may be required where field cables leave the enclosure.
The slew-rate-limited driver reduces high-frequency cable radiation but does not remove the need for controlled topology. Keep connectors and cable transitions compact, avoid long parallel branches, and use twisted-pair wiring with a consistent ground strategy. When device grounds are at substantially different potentials, evaluate an isolated interface rather than relying on the transceiver's ESD rating alone.
Maklumat Kesediaan
The component is an industrial RS-485/RS-422 interface transceiver rather than an automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation.
