PCA9513D - 400kHz SMBus Buffer | NXP Semiconductors
MPN: PCA9513D ✗ Akhir HayatPCA9513D Ringkasan
An I2C bus buffer is a specialized interface IC that reproduces logic levels between a master-side bus and a slave-side bus. The buffered side can remain operational during insertion or removal, helping prevent disturbance of a live communication network. In the broader hierarchy, the PCA9513D belongs to the I2C and SMBus interface-controller family, which sits above bus buffers within interface ICs and broader semiconductor power-management and signal-conditioning systems.
The principal identified characteristics are one buffered channel, a 400 kHz operating-frequency rating, an 8-pin SOIC-compatible package, and hot-pluggable bus operation. The device is intended to provide bus-segment isolation in systems where modules or plug-in cards can be added dynamically. Because the manufacturer marks PCA9513D as discontinued, its documentation and product information are retained for historical design reference rather than new-product selection.
Technically, the PCA9513D uses separate upstream and downstream sides to divide the I2C bus into buffered segments. Its purpose is to improve system behavior during live insertion and removal rather than to increase the standardized bus speed beyond 400 kHz. Designers must still account for capacitance, rise time, pull-up placement, and the electrical behavior of each bus segment when laying out the complete circuit.
Typical uses include hot-swappable industrial backplanes, telecommunications equipment with removable line cards, server peripherals, and embedded systems that add or remove bus-connected modules while other devices remain active. The buffer is especially useful where an unplugged card could otherwise disturb the shared clock and data conductors.
For a new design, verify the complete I2C system against the PCA9513D datasheet, including absolute maximum ratings, timing, supply requirements, and input thresholds. On an existing board, confirm that the original package footprint and signal assignment match before treating another part as a replacement. In a live system, isolate power as well as data when practical so that insertion transients do not propagate through the bus.
This page combines the discontinued-product status, bus-buffer specifications, drop-in replacement assessment, application guidance, and engineering comparison information needed to evaluate the PCA9513D for legacy hardware and controlled replacement programs.
Pilihan pengganti yang segera untuk PCA9513D — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
PCA9513AD
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
PCA9513A
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
PCA9513D Spesifikasi
| Device Type | Hot-pluggable I2C-bus and SMBus buffer |
| Number of Channels | 1 channel |
| Maximum Bus Frequency | 400 kHz |
| Kemasan | 8-pin SO |
| Jenis Pemasangan | Surface mount |
| Terminal Count | 8 terminals |
| Package Shape | Rectangular |
| Terminal Form | Gull wing |
| Temperature Grade | Industrial |
| Bus Type | I2C and SMBus |
| Hot-Plug Support | Yes |
Panduan Konfigurasi Pin PCA9513D rectangular
Konfigurasi pin untuk PCA9513D (rectangular pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk PCA9513D.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
PCA9513D patut untuk 6 aplikasis: Hot-Pluggable Industrial Backplane, Telecommunications Line Cards, Server Peripherals, Embedded Test and Measurement Modules, Removable Sensor Cards, Legacy Peripheral Bus Isolation.
Hot-Pluggable Industrial Backplane
The PCA9513D fits an industrial backplane that accepts or removes I2C or SMBus equipment cards while other devices remain active. Its one-channel hot-pluggable buffer separates the upstream controller from the downstream card-facing bus, helping reduce disturbance when a connector is mated or unmated. The identified 400 kHz operating rating supports standard-speed and fast-mode I2C traffic, while the 8-pin SO package preserves a compact controller-board footprint. The system designer must still control connector power transients, maintain proper pull-up placement, and verify the total capacitance of each isolated segment against the manufacturer limits before treating insertion as electrically safe.
Disebarkan
Telecommunications Line Cards
The PCA9513D is applicable to telecommunications line-card systems in which a removable board communicates through I2C or SMBus and must not corrupt traffic on the active bus. The buffered downstream segment can help isolate the card interface during insertion and removal, supporting more predictable control traffic at the 400 kHz maximum identified frequency. Its one-channel structure suits a dedicated clock-and-data pair rather than a multi-channel multiplexer. Design validation should include connector sequencing, powered-versus-unpowered insertion behavior, bus rise time, pull-up resistor placement, and the exact NXP timing and absolute-maximum-rating tables before deployment.
Disebarkan
Server Peripherals
The PCA9513D can divide a shared I2C or SMBus control bus from a server peripheral or expansion module, reducing the effect of hot insertion on the rest of the bus. Its one-channel, 400 kHz hot-pluggable-buffer arrangement is useful when the server requires deterministic control traffic during module replacement. The 8-pin SO package is convenient for legacy controller and peripheral boards, but thermal and signal-integrity checks remain necessary at the system level. Keep the buffer-side traces short, place pull-ups where they maintain valid rise time on the intended segment, and verify that power-state transitions cannot violate the input limits of the buffer during connector mating.
Disebarkan
Embedded Test and Measurement Modules
The PCA9513D is suitable for legacy test and measurement equipment that connects or disconnects a sensor or instrument module over I2C or SMBus without intentionally interrupting other controllers on the bus. The hot-pluggable buffer creates a segmented bus that can reduce disturbance to the running system, and the 400 kHz rating accommodates common instrument-control traffic. Because this is a one-channel device, the complete I2C clock and data pair must be routed through the corresponding buffered sides. Validate cable length, distributed capacitance, pull-up strength, and connector transients with the actual module because successful logic-level isolation does not eliminate analog or transmission-line effects.
Disebarkan
Removable Sensor Cards
The PCA9513D can isolate a removable sensor card from a controller that continues communicating with other sensors on the shared I2C or SMBus network. Its one-channel hot-pluggable-buffer function is intended to reduce bus disturbance when the card is inserted or removed, and its 400 kHz maximum identified frequency is appropriate for many low-bandwidth sensor-control networks. The system should sequence card power and ground appropriately and use connector and layout techniques that limit switching noise. Before production, verify that each isolated segment remains within the manufacturer-specified capacitance and timing limits and that both sides of the device receive a valid supply during all operating states.
Disebarkan
Legacy Peripheral Bus Isolation
The PCA9513D remains useful in legacy peripheral designs where a controller, printer, storage module, or acquisition board shares an I2C or SMBus connection and may need service access without a full system shutdown. The hot-pluggable buffer provides a segmented interface for the serviceable module, while the 400 kHz operating rating supports the bus class associated with the original PCA9513D design. The compact 8-pin SO package supports repair boards without changing the original footprint. Ensure that replacement components match pin orientation and inspect timing, bus capacitance, and supply sequencing; hot-plug support should not be interpreted as permission to exceed input voltage or current limits.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk PCA9513D — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | PCA9513AD | PCA9513A |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 8-pin SO | 8-pin SO | 8-pin SO |
| Device Function | Hot-pluggable I2C-bus and SMBus buffer | Hot-pluggable I2C-bus and SMBus buffer | Hot-pluggable I2C-bus and SMBus buffer |
| Number of Channels | 1 channel | 1 channel | 1 channel |
| Maximum Bus Frequency | 400 kHz | 400 kHz | 400 kHz |
Penyeberangsung Jelas
- Direct one-channel hot-pluggable bus-buffer function (vsPCA9513AD)
- Compact isolated-bus implementation (vsPCA9513A)
- Established fit for legacy live-backplane repair (vsPCA9513AD)
Catatan Desain
Do not treat hot-pluggable operation as permission to violate the PCA9513D input limits. Connector insertion can introduce powered-versus-unpowered pin mismatches, ground offsets, and ESD transients. Use the manufacturer absolute-maximum-rating and input-threshold tables, control power sequencing where the system permits it, and place suitable protection close to the connector. A functional bus buffer does not by itself guarantee safe insertion into every backplane architecture.
Validate rise time and propagation delay for the complete bus rather than only checking the 400 kHz frequency label. Account for connector and trace capacitance, pull-up resistance, clock stretching, and the delay introduced by the buffered path. Keep upstream and downstream routing compact, place pull-ups on the correct bus segment, and measure the clock waveform at the far end of the longest attached module to confirm that the data setup and hold margins remain acceptable.
For a repair or drop-in substitution, verify the exact SOIC-8 footprint dimensions and lead pitch rather than relying only on the generic 8-pin SO label. Confirm pin-one orientation, keep the footprint free of solder bridges on the fine-pitch leads, and inspect whether the historical board includes an exposed-pad or other thermal feature. The PCA9513AD candidate should be compared pin by pin against the manufacturer datasheet before its package is treated as electrically identical.
The buffered upstream and downstream sides should remain within their specified supply conditions during normal operation and connector transitions. Check whether the downstream module can be inserted before its local supply is valid, and determine whether additional isolation, sequencing, or pull-down components are needed to prevent an intermediate logic state from being interpreted as a bus command. Verify the final design against the manufacturer operating information rather than estimating acceptable logic thresholds.
Maklumat Kesediaan
The manufacturer identifies the PCA9513D as a discontinued industrial-grade interface IC, but the accessible product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.