Texas Instruments

PCA9535RTWR - 16-Bit I/O Expander | Texas Instruments

MPN: PCA9535RTWR ✓ Aktif
2.3 V to 5.5 V Vdss 1 uA maximum Id 24-WQFN, 4 x 4 mm Package 400 kHz Speed
MOQ: 1 |

PCA9535RTWR Ringkasan

The Texas Instruments PCA9535RTWR is a 16-bit I2C and SMBus I/O expander operating from 2.3 V to 5.5 V in a 24-WQFN 4 x 4 mm package. It adds 16 configurable general-purpose digital I/O lines through a two-wire serial interface, includes an interrupt output, and supports a 400 kHz bus speed. The device is intended for systems in which a microcontroller or application processor needs more GPIO pins than are available directly on the host device.

An I/O expander is an interface IC that converts a serial bus into additional parallel digital inputs and outputs. The PCA9535 belongs to the broader hierarchy of serial interface controller, I/O expander, interface IC, and semiconductor. Unlike a GPIO controller integrated into the host processor, this device manages 16 additional lines remotely while the processor reads and writes them through I2C or SMBus transactions.

The PCA9535 provides separate input and output configuration registers, allowing each line to be programmed for input or output operation. Other useful features include polarity inversion for input and output registers, an interrupt output for change detection, and configurable I2C addresses. According to the manufacturer datasheet, the low standby-current consumption is as low as 1 uA, making the device suitable for low-power embedded equipment where peripheral I/O must remain available without continuously loading the power supply.

Its 2.3 V to 5.5 V operating range covers common embedded, industrial, and consumer supply levels. The 400 kHz I2C rate supports reliable communication with microcontrollers and other bus peripherals while avoiding the complexity of a high-speed serial interface. The interrupt output provides a hardware indication that at least one configured input has changed, reducing the need for continuous register polling.

Typical applications include industrial control modules, sensor and actuator interface boards, programmable logic controller peripherals, LED status panels, keyboard scanners, and compact embedded systems. The 16 lines can monitor switches and digital sensors or drive outputs such as indicator LEDs, relays, and latches when the associated circuitry supports the required current and voltage levels.

Designers should confirm pull-up requirements, address selection, and output-current limits in the manufacturer datasheet. Place the device and bus decoupling close to the relevant connector or controlled peripheral, route the I2C and interrupt traces away from noisy power stages, and account for the exposed-pad thermal and layout requirements of the WQFN package.

This product page combines the manufacturer interface details, practical implementation guidance, application fit, and verified drop-in alternatives. It is designed to help engineers evaluate the PCA9535RTWR for new designs, compare compatible devices, and plan a PCB and firmware migration with fewer integration risks.

Pilihan pengganti yang segera untuk PCA9535RTWR — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

PCA9555RTWR

✅ Masuk Drop-In
📦 QFN-24 (4 x 4 mm)
Maintains 16 configurable I/O lines and 400 kHz operation, but adds internal I/O pull-up resistors; standby power can therefore differ when lines are held low.

📋 Alternatif rujukan (tidak dalam katalog)

TCA9555RTWR

✅ Masuk Drop-In
📦 QFN-24 (4 x 4 mm)
Retains 16-bit I2C GPIO expansion in the same 24-WQFN footprint, but its lower-voltage range begins at 1.65 V rather than 2.3 V and it includes internal I/O pull-ups.

📋 Alternatif rujukan (tidak dalam katalog)

PCA9535RTWR Spesifikasi

Number of I/O Lines 16 lines
Jenis Antaramuka I2C and SMBus
Tegangan Pemberi Arus Operasi 2.3 V to 5.5 V
Maximum I2C Bus Frequency 400 kHz
Interrupt Output 1 output
Configuration Registers Present
Low Standby Current 1 uA maximum
Kemasan 24-WQFN, 4 x 4 mm
Jenis Pemasangan Surface mount
Number of Package Pins 24 pins
Status RoHS unknown
REACH Status unknown
AEC-Q100 Qualification unknown

Panduan Konfigurasi Pin PCA9535RTWR 24 pins

Konfigurasi pin untuk PCA9535RTWR (24 pins pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 24 pins untuk PCA9535RTWR

Tiada data garisan pin yang diperoleh untuk PCA9535RTWR.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

PCA9535RTWR patut untuk 6 aplikasis: Industrial Control Module GPIO Expansion, Sensor and Actuator Interface Board, PLC Peripheral Interface, LED Status and Indicator Panel, Keyboard and Control Panel Scanner, Embedded System Peripheral Hub.

🏭

Industrial Control Module GPIO Expansion

The PCA9535RTWR fits industrial control modules that need additional digital command and status signals without expanding the host microcontroller. Its 16 configurable lines can connect discrete inputs, interlocks, and actuator-enable signals while I2C handles register access at up to 400 kHz. The 2.3 V to 5.5 V operating range supports common industrial logic levels, and the interrupt output allows the controller to respond to changed inputs. The main engineering consideration is the output-current limit: use the manufacturer electrical tables to confirm that each load remains within the applicable drive and voltage limits.

🧩

Sensor and Actuator Interface Board

The PCA9535RTWR is useful on sensor and actuator boards where a serial bus must connect to multiple digital devices. Sixteen independently configurable ports can accept sensor status signals and control actuator-enable stages without consuming host GPIO pins. The 400 kHz I2C rate supports efficient register access, while the interrupt output provides a hardware change indication when an input changes. Because the PCA9535 does not include the PCA9555's internal I/O pull-ups, external biasing must be designed where required and checked against the pin-level electrical specifications.

🏭

PLC Peripheral Interface

The PCA9535RTWR can extend a compact controller or peripheral with 16 digital lines for field switches, interlocks, outputs, and status indicators. It preserves a simple two-wire control path and supports I2C operation up to 400 kHz, making it appropriate for low- and medium-speed automation interfaces. The interrupt output can reduce unnecessary bus polling when a monitored input changes. System designers should account for isolation, surge protection, grounding, and output loading separately when connecting the low-voltage expander to industrial wiring.

💡

LED Status and Indicator Panel

The PCA9535RTWR can drive a compact LED status panel when each indicator has an appropriate current-limiting circuit and remains within the port's permitted output loading. Its 16 ports provide more display-control flexibility than most small microcontrollers expose directly. Register-based input/output configuration also permits mixed designs in which some lines start indicators while others monitor panel buttons. The 2.3 V to 5.5 V range supports common 3.3 V and 5 V systems, but designers should verify output drive, voltage, and simultaneous active-line behavior against the manufacturer electrical characteristics.

🔧

Keyboard and Control Panel Scanner

The PCA9535RTWR is well suited to a keyboard or control panel that contains more switches than the host device can scan directly. Sixteen inputs can be configured as digital lines, and the interrupt output can alert the processor when a key or switch state changes. I2C communication at up to 400 kHz allows efficient polling of the port and configuration registers. PCB layout should keep the I2C traces short, provide the required pull-up network, and place ESD protection at accessible connector inputs because the expander itself is not a substitute for connector-level protection.

📱

Embedded System Peripheral Hub

The PCA9535RTWR can serve as a peripheral hub in an embedded system that combines a processor with removable or optional front-panel functions. Its 16 ports support configuration, status, and control signals while the compact 24-WQFN 4 x 4 mm package preserves board area. The 1 uA maximum standby current helps systems that periodically power down, and the 2.3 V minimum operating voltage fits 3.3 V designs. Firmware should initialize the configuration, polarity, and interrupt registers according to the manufacturer register map before using the ports as outputs.

Ringkasan Produk Disebarkan

PCA9535RTWR Texas Instruments Dipergunakan di: Industrial Control Module GPIO Expansion, Sensor and Actuator Interface Board, PLC Peripheral Interface, LED Status and Indicator Panel, Keyboard and Control Panel Scanner, Embedded System Peripheral Hub PCA9555RTWR Same-package GPIO expander with internal pull-ups Dipergunakan di: Industrial Control Module GPIO Expansion, Sensor and Actuator Interface Board, LED Status and Indicator Panel, Keyboard and Control Panel Scanner TCA9555RTWR Same-footprint GPIO expansion alternative Dipergunakan di: PLC Peripheral Interface, Embedded System Peripheral Hub
What is the PCA9535RTWR used for?
The PCA9535RTWR is a 16-bit I2C and SMBus I/O expander that adds 16 configurable digital I/O lines to a host processor. It operates from 2.3 V to 5.5 V, supports I2C communication at up to 400 kHz, and provides an interrupt output for input-change notification. According to the Texas Instruments product page, its configuration registers allow each line to be assigned as an input or output. It is especially useful when a microcontroller has insufficient GPIO pins for switches, sensors, LEDs, relays, or other discrete digital signals.
How many GPIOs does the PCA9535RTWR provide?
The PCA9535RTWR provides 16 general-purpose I/O lines divided into two 8-bit ports. Each line can be configured through the device registers for digital input or digital output operation. According to the Texas Instruments product description, the PCA9535 is a remote 16-bit I2C and SMBus low-power I/O expander with an interrupt output and configuration registers. The two ports can interface with a mixture of control signals and status inputs while sharing the same two-wire serial bus.
What is the operating voltage of PCA9535RTWR?
The PCA9535RTWR operates from 2.3 V to 5.5 V. The Texas Instruments product page identifies the PCA9535 as a 2.3 V to 5.5 V I2C and SMBus I/O expander, making it suitable for embedded systems using either 3.3 V or 5 V power rails. Its I2C interface supports operation at up to 400 kHz. Use the manufacturer pin-description and electrical-characteristics tables when confirming logic thresholds, current limits, and timing margins for the exact system voltage.
Where can I download the PCA9535RTWR datasheet PDF?
The official PCA9535RTWR datasheet is available from the Texas Instruments product page at https://www.ti.com/product/PCA9535, with the manufacturer document link provided at https://www.ti.com/lit/gpn/pca9535. The datasheet contains the pin descriptions, register map, electrical characteristics, application information, and package drawings for the PCA9535 family. For an exact PCA9535RTWR schematic, use the orderable part information to confirm the 24-WQFN 4 x 4 mm package and associated terminal assignments.
Where can I find the PCA9535RTWR pinout?
The PCA9535RTWR pinout is shown in the Pin Configuration and Functions section of the official Texas Instruments PCA9535 datasheet. The target device uses a 24-WQFN 4 x 4 mm package, so the package drawing includes 24 perimeter positions and a thermal pad. Use that table when assigning A0, A1, A2, SCL, SDA, INT, the port pins, and the supply connections. The public page-level records do not reproduce every terminal name, so the manufacturer diagram is the authoritative source for PCB layout.
Can PCA9535RTWR drive LEDs?
The PCA9535RTWR can control LED-related digital signals when the selected port pin, supply rail, and external current-limiting arrangement meet the device's output-current specifications. It provides 16 configurable lines, so it is practical for low-current status indicators, segmented indicators, or relay-control inputs rather than unrestricted LED loads. Check the maximum output current, output voltage, and drive-state specifications in the Texas Instruments datasheet before assigning multiple LEDs or other load currents to one port.
What is the difference between PCA9535RTWR and PCA9555RTWR?
The principal documented difference is the internal I/O pull-up arrangement. The Texas Instruments product page states that the PCA9535 is identical to the PCA9555 except for removal of the internal I/O pull-up resistors, which reduces power consumption when the I/O lines are held low. Both devices provide 16-bit I/O expansion in the same 24-WQFN 4 x 4 mm package. The PCA9535 therefore suits designs that rely on external pull-ups and lower standby consumption, while the PCA9555 offers integrated pull-ups where those resistors are otherwise required.
Is PCA9535RTWR compatible with PCF8575?
The Texas Instruments product page states that the PCA9535 is pin-to-pin and I2C address compatible with the PCF8575, but software changes are required because of the PCA9535's enhanced register functions. That electrical compatibility statement does not by itself establish that every package is a drop-in footprint replacement. A true board-level substitution must also use the same package, pin arrangement, and exposed-pad pattern. Use the package drawings for both devices before reusing an existing PCB layout.
What can replace the PCA9535RTWR?
A PCA9535RTWR replacement must match the 24-WQFN 4 x 4 mm footprint and remain pin-to-pin compatible. The PCA9555RTWR is the closest documented same-package option because it provides the same 16-bit I/O expansion and bus address compatibility while retaining internal I/O pull-ups. That pull-up difference can affect standby current and external resistor requirements, so verify the schematic and input biasing. A substitute is a genuine drop-in option only after its complete pin description and electrical characteristics have been checked against the manufacturer datasheet.
PCA9535RTWR vs TCA9535RTWR: which one should I choose?
Choose the PCA9535RTWR when the design needs a 16-bit, 400 kHz I2C/SMBus expander with low standby current and configurable interrupt behavior. The TCA9535RTWR offers a similar 16-bit interface in the same 24-WQFN 4 x 4 mm package, but it also provides a hardware reset function that must be accounted for in the pin comparison. Because the reset feature changes pin use, confirm that every terminal has the same electrical function and that the PCB footprint and exposed-pad requirements match before treating either device as a drop-in replacement.
When should I choose PCA9535RTWR over PCA9555RTWR?
Choose the PCA9535RTWR when minimizing standby consumption and controlling input pull-ups with external resistors are the priorities. The Texas Instruments product page explains that the PCA9535 removes the internal I/O pull-up resistors found in the PCA9555, reducing power consumption when the I/O lines are held low. Choose the PCA9555RTWR instead when integrated pull-ups simplify the board or are functionally required. Both provide the same 16-bit expansion concept, 2.3 V to 5.5 V range, 400 kHz bus operation, and 24-WQFN package.
Is PCA9535RTWR suitable for an I2C GPIO module?
The PCA9535RTWR is suitable for an I2C GPIO module because it adds 16 independently configurable digital lines, operates from 2.3 V to 5.5 V, and communicates at up to 400 kHz. According to the Texas Instruments product description, the interrupt output can signal a change on a configured input, reducing repeated status polling. The design must still include suitable bus pull-ups and must respect the output-current and logic-level limits shown in the manufacturer electrical-characteristics tables.
How does the PCA9535RTWR interrupt output work?
The PCA9535RTWR provides a dedicated interrupt output to indicate activity involving configured input lines, allowing the host processor to avoid continuously polling all 16 ports. According to the Texas Instruments product page, the device includes an interrupt output together with configuration registers. The interrupt polarity, masking, and port-change behavior should be configured through the manufacturer register definitions. Firmware should also clear or service the relevant status condition before expecting the next interrupt event.
Where to buy PCA9535RTWR online?
Use the Request a Quote form on this product page to request PCA9535RTWR pricing, stock confirmation, minimum order quantity, and lead time. The form provides a single sourcing channel without relying on changing marketplace listings. Because the device is orderable as a specific 24-WQFN package, include the full PCA9535RTWR MPN on the request and state the required production quantity. The current commercial terms should be confirmed when the quotation is returned.
What is the price and lead time of PCA9535RTWR?
Current PCA9535RTWR pricing, stock, minimum order quantity, and lead time are handled through the Request a Quote form on this page. The form is the appropriate route because commercial terms can vary with quantity, production date, and shipment requirements. Include the exact PCA9535RTWR MPN, target annual usage, requested purchase quantity, and delivery location with the request. The manufacturer product page can be used in parallel to confirm device status, package construction, and technical documentation.

Data referensi kejuruteraan untuk PCA9535RTWR — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose PCA9535RTWR when a design needs 16 remote GPIO lines, I2C operation up to 400 kHz, and low standby consumption with external pull-up control. It is particularly appropriate for 3.3 V and 5 V embedded systems where the manufacturer documents a 2.3 V minimum supply voltage. Choose PCA9555RTWR when the same footprint and 16-bit expansion are needed but integrated I/O pull-ups simplify the PCB. Choose TCA9555RTWR when operation below 2.3 V is required or its additional reset and electrical features fit the design. Before assigning any alternative, compare the complete terminal descriptions, interrupt behavior, input thresholds, output-current limits, address configuration, and exposed-pad layout. A shared WQFN outline alone does not guarantee that every peripheral function is interchangeable.

Perbandingan dengan Gantian

Parametr Produk Ini PCA9555RTWR TCA9555RTWR
Brand Texas Instruments Texas Instruments Texas Instruments
Package QFN-24 (4 x 4 mm) QFN-24 (4 x 4 mm) QFN-24 (4 x 4 mm)
I/O Count 16 lines 16 lines 16 lines
Operating Supply Voltage 2.3 V to 5.5 V 2.3 V to 5.5 V 1.65 V to 5.5 V
Maximum Bus Frequency 400 kHz 400 kHz 400 kHz
Internal I/O Pull-Ups Not present Present Present
Interrupt Output Present Present Present
Configuration Registers Present Present Present
Interface I2C and SMBus I2C and SMBus I2C
Mounting Type Surface mount Surface mount Surface mount

Penyeberangsung Jelas

  • Lower standby-power design without integrated I/O pull-ups (vsPCA9555RTWR)
  • Same 16-bit architecture and package (vsPCA9555RTWR)
  • Standard 2.3 V minimum operating voltage (vsTCA9555RTWR)

Catatan Desain

Place the PCA9535RTWR close to the connector or peripheral group served by its 16 I/O lines, and keep the SCL and SDA traces short and away from switching nodes. Provide the required I2C pull-ups on the bus rather than assuming the PCA9535 includes the internal pull-ups available on the PCA9555. Route the exposed pad according to the manufacturer land-pattern and thermal guidance, and preserve access to every perimeter lead for inspection and rework.

Assign the address pins before finalizing the board layout because A0, A1, and A2 can select the device's I2C address. Confirm the address against every other peripheral on the same bus to avoid contention. The interrupt trace should be kept away from high-current switching paths and routed as a low-speed control signal. Where an interrupt connects to a sensitive host input, validate its level and polarity in firmware using the manufacturer register definitions.

Do not assume that the PCA9535RTWR and PCA9555RTWR are electrically identical in every application. The PCA9535 omits the internal I/O pull-up resistors, while the PCA9555 includes them. Verify external pull-up values, input leakage, standby current, and the maximum load on each port using the manufacturer datasheets. Also check whether TCA9535-family alternatives use a reset terminal differently, because an added or repurposed reset function can prevent a footprint-only replacement from being pin-to-pin compatible.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated in the available manufacturer and distributor records. Confirm current compliance documentation with Texas Instruments before production release.

Pencarian Berhubungan

PCA9535RTWR datasheet PCA9535RTWR pinout PCA9535RTWR datasheet pdf PCA9535RTWR 24-WQFN pinout PCA9535RTWR equivalent PCA9535RTWR replacement PCA9535RTWR cross reference PCA9535RTWR vs PCA9555RTWR PCA9535RTWR vs TCA9535RTWR Texas Instruments PCA9535RTWR PCA9535RTWR I2C GPIO expander PCA9535RTWR 16 bit 400 kHz PCA9535RTWR application circuit PCA9535RTWR price PCA9535RTWR stock

Komponen dan Tanda berkaitan

Texas Instruments PCA9535 PCA9535RTWR PCA9555RTWR TCA9555RTWR TCA9535RTWR PCF8575 I/O expander GPIO expander interface IC semiconductor I2C SMBus 24-WQFN QFN package family surface mount SMD remote 16-bit parallel I/O interrupt output configuration registers low standby current industrial control sensor interface actuator interface LED status panel
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ