THS8135PHP - 10-Bit Triple 240-MSPS Video DAC | TI
MPN: THS8135PHP ✓ AktifTHS8135PHP Ringkasan
A DAC is a data converter that translates digital codes into proportional analog voltages or currents. Video DACs belong to the broader ADC/DAC and data-converter IC hierarchy, where they sit between parallel digital pixel data and analog signals used by display or video-processing circuitry. The THS8135PHP combines three converters with circuitry for bi-level or tri-level synchronization and blanking-level generation.
The principal features of this device are its three independent 10-bit conversion channels, 240 MSPS performance, parallel digital interface, and dedicated analog and digital supply rails. Each converter resolves the video signal into 10-bit steps. The parallel interface supports direct connection to video data sources without requiring a serial interface or a separate high-speed communication protocol. The package also provides a consolidated implementation for three color channels rather than requiring three separate DAC packages.
The architecture is tailored to conventional component and graphics video systems. ITU-R BT.601-compatible full-scale output is identified for this device, making its output scaling suitable for standard-definition digital-video workflows. Bi-level and tri-level sync generation can produce the blanking levels required when converting active digital video into analog composite video. The 3.3 V analog rail and 1.8 V digital rail support partitioned supply planning, although both rails and the interface still require careful decoupling.
Typical applications include SD and other video graphics systems, test and measurement video generation, digital signage, display-processing boards, and industrial imaging panels. The device is particularly useful when three synchronized analog outputs are required and the source interface already provides parallel pixel data. Its 240 MSPS ceiling provides substantial timing margin for common progressive video rates.
PCB design should keep analog and digital return currents separated, place supply capacitors close to their corresponding pins, and route the parallel data bus with matched-length practices where timing margin is limited. The 48-lead HTQFP also requires careful thermal design because sustained high update rates can increase package dissipation. Use the manufacturer's pin-description table when assigning every power, data, clock, sync, and output connection.
This page combines the device's principal conversion specifications, application guidance, package details, and engineering-focused replacement considerations. It also organizes sourcing information and drop-in comparison points into a format intended to accelerate schematic review, footprint verification, and prototype planning.
Pilihan pengganti yang segera untuk THS8135PHP — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera THS8135PHP (sama faktor bentuk dan kaki) — berbeza dalam Maximum Sampling Rate.
THS8136PHP
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →THS8137PHP
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
THS8138PHP
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
THS8139PHP
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
THS8135PHPG4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
THS8135PHP Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | Triple video digital-to-analog converter |
| Number of DAC Channels | 3 channels |
| Pemecahkatan | 10 bits per channel |
| Maximum Sampling Rate | 240 MSPS |
| Analog Supply Voltage | 3.3 V |
| Digital Supply Voltage | 1.8 V |
| Digital Interface | Parallel |
| Output Compliance | ITU-R BT.601 full-scale range |
| Synchronization Support | Bi-level and tri-level sync |
| Blanking Support | Blanking-level generation |
| Package Type | 48-lead HTQFP |
| Package Dimensions | 7 mm x 7 mm |
| Terminal Count | 48 terminals |
| Lead Form | Gull-wing |
| Temperature Grade | Commercial grade |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin THS8135PHP 7 mm x 7 mm
Konfigurasi pin untuk THS8135PHP (7 mm x 7 mm pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk THS8135PHP.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
THS8135PHP patut untuk 6 aplikasis: Standard-Definition Video Output, Digital Signage Player, Video Test and Measurement, Industrial Imaging Panel, Digital-to-Analog Video Conversion, Graphics and Display Processing.
Standard-Definition Video Output
The THS8135PHP is appropriate for a standard-definition video board that receives parallel RGB or component-style digital codes and requires three synchronized analog outputs. Its three 10-bit conversion channels provide matching color-channel resolution, while the 240 MSPS maximum rate offers timing headroom over common SD pixel clocks. The device operates from a 3.3 V analog rail and a 1.8 V digital rail, allowing the interface logic and converter sections to use separate supply networks. ITU-R BT.601-compliant full-scale output supports conventional video scaling. The implementation should include channel-matched output networks, local supply decoupling, controlled reference return paths, and timing verification for the source video clock.
Disebarkan
Digital Signage Player
A digital-signage controller can use the THS8135PHP when it drives a video display through three parallel digital color channels. The 10-bit-per-channel converter supports smoother analog gradient reproduction than lower-resolution designs, while the 240 MSPS ceiling is well above many display timing rates. The parallel interface simplifies connection to video timing logic already present in the controller. Separate 3.3 V analog and 1.8 V digital supplies allow the board to isolate sensitive output circuitry from logic. Keep the digital bus away from the analog output region, reference a local ground strategy, and confirm that the controller can accommodate the converter's sync and blanking-generation functions.
Disebarkan
Video Test and Measurement
The THS8135PHP is useful in video test equipment that must generate three analog color outputs from digital test patterns. Its 240 MSPS sampling capability provides substantial timing margin for common laboratory video formats, while three matched 10-bit converters simplify coordinated RGB generation. The parallel input bus can accept patterns from FPGA-based or digital video engines. Because test equipment often evaluates low-level distortion, keep analog and digital supplies independently decoupled, use symmetrical routing where practical, and establish a single quiet return point for the converter and output networks. Verify cable-driver bandwidth and termination because those external stages may limit final accuracy.
Disebarkan
Industrial Imaging Panel
The THS8135PHP can support industrial imaging and panel-display systems requiring synchronized RGB output from a digital frame processor. The triple 10-bit architecture applies the same conversion resolution to all three color paths, and the 240 MSPS rate accommodates a broad range of progressive timing formats. Its 48-lead HTQFP package contains the converter, sync, and blanking functions in a compact 7 mm by 7 mm outline. The board should provide filtered analog and digital rails, minimize return-path discontinuities, and maintain consistent channel delays. Industrial temperature, EMC, and reliability requirements should be checked against the exact ordered device grade before production release.
Disebarkan
Digital-to-Analog Video Conversion
The THS8135PHP is designed for designs that require direct parallel digital-video conversion into three analog channels. A 10-bit code maps to a discrete output step, while the shared device architecture provides consistent conversion across the color channels. Its 240 MSPS operating ceiling makes it suitable for common graphics and video rates without relying on a lower-speed conversion engine. Use the manufacturer's output-recommendation section to determine resistor values, loading, and termination. The 3.3 V analog and 1.8 V digital rails should each have local high-frequency bypass, and clock routing should be short to prevent data-to-clock skew from limiting the usable video bandwidth.
Disebarkan
Graphics and Display Processing
The THS8135PHP is well matched to graphics-processing boards that convert parallel pixel data into three synchronized analog video outputs. The 240 MSPS maximum rate supports common display modes with timing margin, and the 10-bit resolution applies consistently to each color channel. Integration of bi-level or tri-level synchronization and blanking-level generation simplifies implementation when the source does not already provide every required analog timing level. Layout quality remains critical: route the parallel bus away from output networks, provide a controlled analog ground region, and place decoupling capacitors directly at the supply terminals. Confirm connector impedance, cable losses, and amplifier bandwidth to ensure the converter is not the limiting stage.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk THS8135PHP — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | THS8136PHP | THS8137PHP | THS8138PHP | THS8139PHP |
|---|---|---|---|---|---|
| Package | 48-lead HTQFP (7 mm x 7 mm) | 48-lead HTQFP (7 mm x 7 mm) | 48-lead HTQFP (7 mm x 7 mm) | 48-lead HTQFP (7 mm x 7 mm) | 48-lead HTQFP (7 mm x 7 mm) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
Penyeberangsung Jelas
- Integrated triple-converter implementation (vsTHS8136PHP)
- Directly specified for 240 MSPS operation (vsTHS8139PHP)
- Separate analog and digital operating rails (vsTHS8135PHPG4)
Catatan Desain
Separate the analog and digital supply networks as closely as practical while maintaining a single, controlled ground reference at the converter. Place the required bypass capacitors adjacent to their respective supply terminals, and keep the parallel data traces away from the three analog output nodes. Use the manufacturer layout example as the baseline for return paths and component placement rather than relying on a generic high-speed DAC layout.
Treat the clock and parallel data interface as a coordinated timing group. Route the clock away from noisy switching nodes, check source and trace skew, and add matching only when required by the source timing specification. The THS8135PHP supports sampling rates up to 240 MSPS, but practical video bandwidth also depends on output networks, downstream amplifiers, cable loading, and the edge rate of the driving logic. Validate those interactions with measurements from the assembled board.
Build the 3.3 V analog and 1.8 V digital rails so switching and digital return current do not share the most sensitive converter paths. Check regulator noise, decoupling effectiveness, and startup sequencing at the system level. Place bulk and high-frequency capacitance according to the manufacturer's application circuit, and verify that the external output network does not create excessive load or induce code-dependent supply current that reduces available timing margin.
Maklumat Kesediaan
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements were identified for the exact THS8135PHP order code.