TJA1028T/5V0/10 - 5V LIN Transceiver with Regulator | NXP
MPN: TJA1028T/5V0/10 ✓ AktifTJA1028T/5V0/10 Ringkasan
A LIN transceiver is an interface integrated circuit that connects a microcontroller or application processor to the wired- LIN, or Local Interconnect Network, bus. It combines a physical-layer bus driver and receiver with logic-compatible transmit and receive signals. A local interconnect network falls within the broader automotive and industrial communication hierarchy: LIN bus transceiver, wired network interface, interface IC, and semiconductor.
The TJA1028 supports LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 for 12 V systems. The integrated regulator provides a nominal 5.0 V output with a listed 4.9 V to 5.1 V range, reducing the number of external power components needed at a compact LIN node. The transceiver architecture also supports half-duplex LIN communication and strong electrostatic protection.
The 8-SO package makes the TJA1028 suitable for compact modules, electronic control units, sensors, and actuator nodes. Its integrated supply architecture is particularly useful when the bus-powered electronics require a stable local rail but the available system voltage varies. The regulator output should not be treated as a general-purpose high-current power source because its specified capability is limited to 70 mA.
Use the LIN and RXD connections according to the manufacturer pin-description table, and connect the TXD signal to a compatible microcontroller serial interface. The transceiver requires suitable bus termination and external decoupling in accordance with the manufacturer application circuit. Consider power-state behavior, ground strategy, and the regulator load requirement before laying out the PCB.
This product overview combines bus-standard compliance, regulator capability, package details, drop-in alternatives, and practical PCB guidance to support faster component selection. It also distinguishes direct NXP family replacements from choices that require different regulator output or package considerations.
Pilihan pengganti yang segera untuk TJA1028T/5V0/10 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
TJA1028DT
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TJA1028T/5V0/20
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TJA1027T/5V0/10
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
TJA1028T/5V0/10 Spesifikasi
| Product Type | LIN bus transceiver with integrated voltage regulator |
| LIN Standards | LIN 2.0 and LIN 2.1 |
| Automotive Network Compatibility | SAE J2602 |
| International LIN Compliance | ISO 17987-4:2016 (12 V) |
| Nominal Regulator Output | 5.0 V |
| Regulator Output Range | 4.9 V to 5.1 V |
| Maximum Regulator Output Current | 70 mA |
| Operating Supply Range | 5.5 V to 28 V DC |
| Maximum LIN Data Rate | 10 kbit/s |
| Bus Interface Type | Half-duplex LINbus |
| Integrated Voltage Regulator | Yes, low-dropout regulator |
| Available Regulator Variants | 3.3 V and 5.0 V |
| Kemasan | 8-SO, 8-pin SOIC |
| Kiraan Pin | 8 pins |
| Jenis Pemasangan | Surface-mount |
| Electrostatic Protection | Strong electrostatic protection |
Konfigurasi Pin TJA1028T/5V0/10
| Pin 1 | VBB — Voltage regulator battery-side input |
| Pin 2 | LIN — LIN bus transceiver connection |
| Pin 3 | GND — Ground connection |
| Pin 4 | RXD — LIN receive data output |
| Pin 5 | TXD — LIN transmit data input |
| Pin 6 | VCC — 5 V regulator output |
| Pin 7 | VSUP — Bus-side supply input |
| Pin 8 | GND — Ground connection |
Aplikasi Biasa
TJA1028T/5V0/10 patut untuk 6 aplikasis: Automotive LIN Sensor Node, Vehicle Door and Body Control Module, Industrial LIN Actuator, Automotive HVAC Control Node, Compact LIN Gateway Interface, Battery-Powered LIN Sensor Hub.
Automotive LIN Sensor Node
The TJA1028T/5V0/10 fits a compact automotive LIN sensor node because it combines a 10 kbit/s half-duplex LIN interface with a 5.0 V regulator capable of delivering 70 mA. The node can use VSUP for the bus-side supply and obtain a local regulated rail for a sensor interface or low-power microcontroller. LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 positioning support robust 12 V network designs. Keep the regulator load below 70 mA and validate EMC behavior in the complete module.
Disebarkan
Vehicle Door and Body Control Module
The TJA1028T/5V0/10 is suitable for a compact body-control module that connects switches, latch drivers, or other distributed devices to a LIN subnetwork. Its 5.5 V to 28 V operating supply range covers typical low-voltage vehicle environments, while the integrated 5.0 V rail can serve local logic with up to 70 mA. The half-duplex LIN interface reduces wiring compared with point-to-point links. Design the ground and LIN routing to minimize radiated emissions and confirm transient immunity in the final vehicle platform.
Disebarkan
Industrial LIN Actuator
The TJA1028T/5V0/10 can support a compact actuator controller where a low-cost wired bus carries commands to a motor, valve, or relay driver. The transceiver's 10 kbit/s rate is appropriate for control and status traffic rather than high-bandwidth data, and its 5.0 V regulator output can power limited local electronics. Separate the LIN return path cleanly, use the recommended bus termination, and avoid using the 70 mA regulator output for a motor or high-current actuator driver.
Disebarkan
Automotive HVAC Control Node
The TJA1028T/5V0/10 is useful in an HVAC control node that receives commands over a LIN subnetwork while supplying a small local control circuit. Its integrated 5.0 V regulator reduces the component count compared with a separate LIN transceiver and LDO, and its stated 5.5 V to 28 V supply range suits vehicle electrical environments. The regulator must remain below 70 mA, while LIN routing should be isolated from switching outputs to reduce common-mode noise and electromagnetic interference.
Disebarkan
Compact LIN Gateway Interface
The TJA1028T/5V0/10 can serve as the physical-layer interface on a compact LIN gateway or protocol-conversion board. It provides a 10 kbit/s half-duplex bus connection, TXD and RXD logic signals, and a regulated 5.0 V local output for interface electronics. This combination supports board consolidation without introducing a separate regulator. Place the device near the connector, provide a direct return path, and follow the manufacturer application circuit for decoupling and bus termination to preserve signal integrity.
Disebarkan
Battery-Powered LIN Sensor Hub
The TJA1028T/5V0/10 fits a low-energy sensor hub connected to a LIN master when the hub requires a stable 5.0 V logic rail and a robust bus interface. Its integrated low-drop regulator can deliver up to 70 mA, allowing local sensing circuitry to share the node's supply arrangement. Because LIN nodes remain connected to the vehicle electrical environment, validate standby current, supply transients, and bus wake-up behavior in the completed design rather than selecting the regulator solely from nominal output voltage.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk TJA1028T/5V0/10 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | TJA1028DT | TJA1028T/5V0/20 | TJA1027T/5V0/10 |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Product Function | LIN transceiver with integrated voltage regulator | LIN transceiver with integrated voltage regulator | LIN transceiver with integrated voltage regulator | LIN transceiver with integrated voltage regulator |
| Nominal Regulator Output | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| Bus Interface | Half-duplex LINbus | Half-duplex LINbus | Half-duplex LINbus | Half-duplex LINbus |
| Integrated Regulator | Yes, low-dropout voltage regulator | Yes | Yes | Yes |
Penyeberangsung Jelas
- Combines LIN physical-layer interface and local 5 V regulator (vsA discrete LIN transceiver and separate regulator implementation)
- Direct NXP family replacement path (vsTJA1028DT)
- Specified 5 V regulation simplifies local node design (vsTJA1028T/3V3/10)
- Automotive-oriented LIN compliance positioning (vsTJA1027T/5V0/10)
Catatan Desain
Place the TJA1028 close to the LIN connector and route LIN as a controlled-impedance trace with a continuous return path. Keep the TXD and RXD traces away from the LIN connection and switching-node circuitry to reduce common-mode coupling. Connect the required bus termination in the manner shown by the manufacturer application circuit, and avoid long copper stubs between the transceiver, connector, and termination point.
The integrated regulator is specified for output currents up to 70 mA. Include startup current, local logic demand, and peripheral load when calculating the worst-case demand; do not treat the 5.0 V output as a general-purpose supply. Use the manufacturer-recommended input and output capacitors, maintain the required minimum capacitance and ESR characteristics, and verify the regulator's operating region across the complete VSUP range.
Provide a low-impedance ground connection for the transceiver and regulator return current. Place the regulator input capacitor close to VSUP and the output capacitor close to VCC and ground, following the datasheet layout guidance. Keep sensitive RXD routing away from LIN and inductive loads. Correct grounding and capacitor placement are especially important when the module combines the LIN interface with switching actuators or rapidly changing loads.
Do not confuse the 5V0 configuration with the 3.3 V TJA1028 variant, and verify the complete ordering suffix when making a replacement. Likewise, confirm that the board footprint matches SOIC-8 rather than a leaded or alternative package. Before substituting TJA1028DT, TJA1028T/5V0/20, or TJA1027T/5V0/10, compare temperature range, automotive qualification, pin definitions, and regulator electrical limits.
Maklumat Kesediaan
The manufacturer identifies LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 (12 V) compliance. Environmental and automotive qualification declarations for the exact ordering suffix require confirmation from NXP.