TS972IYD - Dual 12MHz Rail-to-Rail Op Amp | STMicroelectronics
MPN: TS972IYD ✗ Akhir HayatTS972IYD Ringkasan
An operational amplifier, or op amp, is a voltage-gain building block within analog and mixed-signal electronics. Its feedback network can create stable gain, filtering, buffering, summing, and current-control functions. The TS972IYD belongs to the operational-amplifier hierarchy, which includes rail-to-rail amplifiers, low-noise amplifiers, and low-voltage general-purpose devices used in analog signal chains.
Key features of the TS972IYD include two amplifiers per package, rail-to-rail output operation, a 12 MHz gain-bandwidth product, and very low-noise characteristics. Rail-to-rail output allows the output stage to approach the supply limits, which helps maximize signal range in low-voltage systems. The dual configuration reduces board area by integrating two amplifier channels into one 8-pin SOIC package.
The TS97x family operates from voltages as low as ±1.35 V and is designed for portable and battery-supplied equipment. Its combination of low-noise, low-distortion behavior, wide output swing, and moderate bandwidth supports audio preamplification, sensor conditioning, active filtering, and general analog signal processing. Engineers should account for input common-mode range, output swing, capacitive-load stability, and supply-voltage limits when selecting operating points.
Typical uses include audio preamplifiers, microphone and sensor interfaces, battery-powered instrumentation, active filters, buffer stages, and low-voltage control systems. In each case, the dual channel arrangement can support paired signal paths or provide an unused amplifier for filtering, level shifting, or test functions while keeping the footprint compact.
For a new layout, route the bypass capacitor directly to the supply and ground pins, keep feedback traces short, and verify stability with the intended source impedance and load. Component substitutions require confirmation of the SOIC footprint, pin functions, supply range, common-mode behavior, output swing, bandwidth, and noise performance rather than package similarity alone.
This product page combines the device identity, package information, documented operating characteristics, sourcing workflow, and engineering guidance. It also distinguishes confirmed TS97x-family options from unsupported substitute claims and focuses replacement analysis on genuine pin-compatible, same-package possibilities rather than merely similar amplifier functions.
Pilihan pengganti yang segera untuk TS972IYD — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera TS972IYD (sama faktor bentuk dan kaki) — berbeza dalam Package.
TS972IQT
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →TS972IST
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TS972IYD Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | Dual general-purpose operational amplifier |
| Number of Amplifier Channels | 2 circuits |
| Gain-Bandwidth Product | 12 MHz |
| Output Architecture | Rail-to-rail output |
| Minimum Total Supply Voltage | 2.7 V (±1.35 V) |
| Kemasan | 8-pin SOIC |
| Jenis Pemasangan | Surface mount |
| Automotive Series Identification | I-grade identification |
Panduan Konfigurasi Pin TS972IYD 8-pin soic
Konfigurasi pin untuk TS972IYD (8-pin soic pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk TS972IYD.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
TS972IYD patut untuk 6 aplikasis: Low-Voltage Audio Preamplifier, Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Active Audio Filtering, Industrial Control Signal Interface, Data Acquisition Front End.
Low-Voltage Audio Preamplifier
The TS972IYD fits dual audio preamplifier paths because the device combines two amplifiers, rail-to-rail output swing, very low noise, and a 12 MHz gain-bandwidth product in one 8-pin SOIC package. It can provide gain and buffering ahead of a codec, line input, or headphone-driver stage when operated near low supply rails. Rail-to-rail output increases usable signal range in portable systems, while the dual channel count reduces board area. Before finalizing the gain network, verify the exact input-voltage noise, distortion, common-mode range, and maximum output swing under the selected supply voltage and load.
Disebarkan
Portable Sensor Signal Conditioning
The TS972IYD is suitable for conditioning signals from low-voltage sensors in portable or battery-powered instruments. Operation from voltages as low as ±1.35 V supports reduced-energy systems, while dual rail-to-rail channels can handle a sensor signal and a reference or auxiliary signal path. The 12 MHz bandwidth provides useful margin for moderate-bandwidth filters and instrumentation stages. The design must remain inside the amplifier's input common-mode range and output-swing limits, and it should include an anti-alias filter and decoupling capacitor placed close to the supply pins.
Disebarkan
Battery-Powered Instrumentation
The TS972IYD's low-voltage capability and rail-to-rail output make it applicable to compact battery-powered instrumentation where signal headroom is limited. Two independent amplifiers can implement gain, buffering, active filtering, or difference functions in a shared 8-pin SOIC footprint. The very-low-noise positioning is useful when reducing the contribution of the amplifier itself to weak sensor measurements, and the 12 MHz gain-bandwidth product supports several common low-frequency and audio-band signal paths. Validate offset, bias current, supply-current consumption, and noise at the intended signal level and temperature range.
Disebarkan
Active Audio Filtering
The TS972IYD can implement active filters because each rail-to-rail channel may be configured with external resistors and capacitors, and its 12 MHz gain-bandwidth product provides bandwidth for audio-band filter sections. Dual packaging is especially efficient for stereo filtering, differential signal conditioning, or a filter plus buffer arrangement. Component tolerances and amplifier noise set the achievable filter response, so stable resistors and suitable capacitor types should be used. Stability should also be checked with the source impedance, output loading, and any cable capacitance expected in the finished assembly.
Disebarkan
Industrial Control Signal Interface
The dual TS972IYD can serve as an interface between low-level control signals and higher-level circuitry in industrial equipment. Its rail-to-rail output allows wider signal swing on low-voltage rails, while the two channels can amplify one command while buffering a feedback or monitor signal. The 8-pin SOIC package supports compact surface-mount layouts, and the 12 MHz bandwidth is more than adequate for many slow control loops. Engineers should confirm common-mode limits, input protection strategy, output loading, and channel-to-channel behavior before connecting external equipment or long wiring.
Disebarkan
Data Acquisition Front End
The TS972IYD may serve as an analog front-end amplifier in a compact data-acquisition system requiring low-voltage, low-noise signal conditioning. Two channels can process differential or related inputs, and the 12 MHz gain-bandwidth product allows useful loop gain at moderate signal frequencies. Rail-to-rail operation helps maximize dynamic range when the converter or system uses a restricted supply. The amplifier's offset and noise contribute directly to acquisition accuracy, so the selected gain, source impedance, bandwidth, settling requirements, and external anti-alias filter must be evaluated together before choosing the device.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk TS972IYD — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | TS972IQT | TS972IST |
|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-SOIC | 8-SOIC | 8-SOIC |
| Amplifier Channels | 2 circuits | 2 circuits | 2 circuits |
| Product Class | Standard general-purpose amplifier | TS97x general-purpose amplifier | TS97x general-purpose amplifier |
| Gain-Bandwidth Product | 12 MHz | 12 MHz | 12 MHz |
| Output Architecture | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
| Minimum Total Supply Voltage | 2.7 V (±1.35 V) | 2.7 V (±1.35 V) | 2.7 V (±1.35 V) |
| Noise Positioning | Very low noise | Very low noise | Very low noise |
| Orderable Suffix | IYD | IQT | IST |
Penyeberangsung Jelas
- Combines dual amplification with low-voltage rail-to-rail operation (vsTS972IQT)
- Provides higher bandwidth than typical general-purpose precision amplifiers (vsTS972IST)
- Targets low-noise audio and portable signal conditioning (vsTS972IQT)
Catatan Desain
Place the supply bypass capacitor immediately between the device supply and ground pins, with the shortest possible loop. For an 8-SOIC implementation, keep the capacitor and amplifier ground connection on the same PCB layer where practical to reduce parasitic inductance. Add separate bulk capacitance at the power-source entry point so that switching and wiring inductance do not appear directly across the amplifier pins.
Keep input, feedback, and output traces short and away from noisy switching nodes and high-current paths. Maintain a continuous ground reference beneath the device and sensitive analog traces where the board stack-up permits. Because the TS972IYD can be used with external feedback networks, component leads and ground-return paths should be arranged to minimize parasitic feedback and input capacitance.
Check output stability with the actual source impedance, load capacitance, cable length, and feedback network. An 8-pin SOIC amplifier can become conditionally unstable when driving large capacitive loads because the extra capacitance interacts with output and feedback poles. If a capacitive load is unavoidable, add an isolation resistor near the output or revise the feedback network, and verify stability with an oscilloscope and appropriate capacitive loads.
Do not treat the rail-to-rail output description as permission for unlimited input or output swing. Confirm the input common-mode range and output voltage limits at the actual supply voltage, and include output headroom for distortion and load-current variation. Similarly, operation from ±1.35 V describes a family capability but does not by itself establish that every application, temperature, and output-load condition satisfies the exact orderable device limits.
Maklumat Kesediaan
One indexed catalog associates the I-grade family with automotive identification and AEC-Q100, but an exact TS972IYD qualification statement is not present. Treat the exact-device compliance status as unknown until confirmed from the manufacturer datasheet or product documentation.