TS972IYD - Dual 12MHz Rail-to-Rail Op Amp | STMicroelectronics
料号: TS972IYD ✗ 停产TS972IYD 概述
An operational amplifier, or op amp, is a voltage-gain building block within analog and mixed-signal electronics. Its feedback network can create stable gain, filtering, buffering, summing, and current-control functions. The TS972IYD belongs to the operational-amplifier hierarchy, which includes rail-to-rail amplifiers, low-noise amplifiers, and low-voltage general-purpose devices used in analog signal chains.
Key features of the TS972IYD include two amplifiers per package, rail-to-rail output operation, a 12 MHz gain-bandwidth product, and very low-noise characteristics. Rail-to-rail output allows the output stage to approach the supply limits, which helps maximize signal range in low-voltage systems. The dual configuration reduces board area by integrating two amplifier channels into one 8-pin SOIC package.
The TS97x family operates from voltages as low as ±1.35 V and is designed for portable and battery-supplied equipment. Its combination of low-noise, low-distortion behavior, wide output swing, and moderate bandwidth supports audio preamplification, sensor conditioning, active filtering, and general analog signal processing. Engineers should account for input common-mode range, output swing, capacitive-load stability, and supply-voltage limits when selecting operating points.
Typical uses include audio preamplifiers, microphone and sensor interfaces, battery-powered instrumentation, active filters, buffer stages, and low-voltage control systems. In each case, the dual channel arrangement can support paired signal paths or provide an unused amplifier for filtering, level shifting, or test functions while keeping the footprint compact.
For a new layout, route the bypass capacitor directly to the supply and ground pins, keep feedback traces short, and verify stability with the intended source impedance and load. Component substitutions require confirmation of the SOIC footprint, pin functions, supply range, common-mode behavior, output swing, bandwidth, and noise performance rather than package similarity alone.
This product page combines the device identity, package information, documented operating characteristics, sourcing workflow, and engineering guidance. It also distinguishes confirmed TS97x-family options from unsupported substitute claims and focuses replacement analysis on genuine pin-compatible, same-package possibilities rather than merely similar amplifier functions.
直接替换替代料: TS972IYD ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TS972IYD (相同外形与封装尺寸) ——差异在于 Package.
TS972IQT
✅ 直接替换联系询价
查看数据手册 →TS972IST
✅ 直接替换📋 参考替代料(不在目录中)
TS972IYD 最大额定值与电气特性
| Product Type | Dual general-purpose operational amplifier |
| Number of Amplifier Channels | 2 circuits |
| Gain-Bandwidth Product | 12 MHz |
| Output Architecture | Rail-to-rail output |
| Minimum Total Supply Voltage | 2.7 V (±1.35 V) |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
| Automotive Series Identification | I-grade identification |
TS972IYD 8-pin soic 引脚配置指南
TS972IYD(8-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TS972IYD.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TS972IYD 适用于 6 应用s: Low-Voltage Audio Preamplifier, Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Active Audio Filtering, Industrial Control Signal Interface, Data Acquisition Front End.
Low-Voltage Audio Preamplifier
The TS972IYD fits dual audio preamplifier paths because the device combines two amplifiers, rail-to-rail output swing, very low noise, and a 12 MHz gain-bandwidth product in one 8-pin SOIC package. It can provide gain and buffering ahead of a codec, line input, or headphone-driver stage when operated near low supply rails. Rail-to-rail output increases usable signal range in portable systems, while the dual channel count reduces board area. Before finalizing the gain network, verify the exact input-voltage noise, distortion, common-mode range, and maximum output swing under the selected supply voltage and load.
推荐
Portable Sensor Signal Conditioning
The TS972IYD is suitable for conditioning signals from low-voltage sensors in portable or battery-powered instruments. Operation from voltages as low as ±1.35 V supports reduced-energy systems, while dual rail-to-rail channels can handle a sensor signal and a reference or auxiliary signal path. The 12 MHz bandwidth provides useful margin for moderate-bandwidth filters and instrumentation stages. The design must remain inside the amplifier's input common-mode range and output-swing limits, and it should include an anti-alias filter and decoupling capacitor placed close to the supply pins.
推荐
Battery-Powered Instrumentation
The TS972IYD's low-voltage capability and rail-to-rail output make it applicable to compact battery-powered instrumentation where signal headroom is limited. Two independent amplifiers can implement gain, buffering, active filtering, or difference functions in a shared 8-pin SOIC footprint. The very-low-noise positioning is useful when reducing the contribution of the amplifier itself to weak sensor measurements, and the 12 MHz gain-bandwidth product supports several common low-frequency and audio-band signal paths. Validate offset, bias current, supply-current consumption, and noise at the intended signal level and temperature range.
推荐
Active Audio Filtering
The TS972IYD can implement active filters because each rail-to-rail channel may be configured with external resistors and capacitors, and its 12 MHz gain-bandwidth product provides bandwidth for audio-band filter sections. Dual packaging is especially efficient for stereo filtering, differential signal conditioning, or a filter plus buffer arrangement. Component tolerances and amplifier noise set the achievable filter response, so stable resistors and suitable capacitor types should be used. Stability should also be checked with the source impedance, output loading, and any cable capacitance expected in the finished assembly.
推荐
Industrial Control Signal Interface
The dual TS972IYD can serve as an interface between low-level control signals and higher-level circuitry in industrial equipment. Its rail-to-rail output allows wider signal swing on low-voltage rails, while the two channels can amplify one command while buffering a feedback or monitor signal. The 8-pin SOIC package supports compact surface-mount layouts, and the 12 MHz bandwidth is more than adequate for many slow control loops. Engineers should confirm common-mode limits, input protection strategy, output loading, and channel-to-channel behavior before connecting external equipment or long wiring.
推荐
Data Acquisition Front End
The TS972IYD may serve as an analog front-end amplifier in a compact data-acquisition system requiring low-voltage, low-noise signal conditioning. Two channels can process differential or related inputs, and the 12 MHz gain-bandwidth product allows useful loop gain at moderate signal frequencies. Rail-to-rail operation helps maximize dynamic range when the converter or system uses a restricted supply. The amplifier's offset and noise contribute directly to acquisition accuracy, so the selected gain, source impedance, bandwidth, settling requirements, and external anti-alias filter must be evaluated together before choosing the device.
推荐
推荐产品汇总
工程参考数据: TS972IYD ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TS972IQT | TS972IST |
|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-SOIC | 8-SOIC | 8-SOIC |
| Amplifier Channels | 2 circuits | 2 circuits | 2 circuits |
| Product Class | Standard general-purpose amplifier | TS97x general-purpose amplifier | TS97x general-purpose amplifier |
| Gain-Bandwidth Product | 12 MHz | 12 MHz | 12 MHz |
| Output Architecture | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
| Minimum Total Supply Voltage | 2.7 V (±1.35 V) | 2.7 V (±1.35 V) | 2.7 V (±1.35 V) |
| Noise Positioning | Very low noise | Very low noise | Very low noise |
| Orderable Suffix | IYD | IQT | IST |
关键差异点
- Combines dual amplification with low-voltage rail-to-rail operation (对比 TS972IQT)
- Provides higher bandwidth than typical general-purpose precision amplifiers (对比 TS972IST)
- Targets low-noise audio and portable signal conditioning (对比 TS972IQT)
设计说明
Place the supply bypass capacitor immediately between the device supply and ground pins, with the shortest possible loop. For an 8-SOIC implementation, keep the capacitor and amplifier ground connection on the same PCB layer where practical to reduce parasitic inductance. Add separate bulk capacitance at the power-source entry point so that switching and wiring inductance do not appear directly across the amplifier pins.
Keep input, feedback, and output traces short and away from noisy switching nodes and high-current paths. Maintain a continuous ground reference beneath the device and sensitive analog traces where the board stack-up permits. Because the TS972IYD can be used with external feedback networks, component leads and ground-return paths should be arranged to minimize parasitic feedback and input capacitance.
Check output stability with the actual source impedance, load capacitance, cable length, and feedback network. An 8-pin SOIC amplifier can become conditionally unstable when driving large capacitive loads because the extra capacitance interacts with output and feedback poles. If a capacitive load is unavoidable, add an isolation resistor near the output or revise the feedback network, and verify stability with an oscilloscope and appropriate capacitive loads.
Do not treat the rail-to-rail output description as permission for unlimited input or output swing. Confirm the input common-mode range and output voltage limits at the actual supply voltage, and include output headroom for distortion and load-current variation. Similarly, operation from ±1.35 V describes a family capability but does not by itself establish that every application, temperature, and output-load condition satisfies the exact orderable device limits.
合规信息
One indexed catalog associates the I-grade family with automotive identification and AEC-Q100, but an exact TS972IYD qualification statement is not present. Treat the exact-device compliance status as unknown until confirmed from the manufacturer datasheet or product documentation.