Analog Devices

ADM489ABRZ - 250kbps Full-Duplex RS-485 IC | Analog Devices

MPN: ADM489ABRZ ✓ Active
5 V Vdss EIA RS-485 and RS-422 Rds(on) 14-lead SOIC Package
MOQ: 1 |

ADM489ABRZ Overview

The Analog Devices ADM489ABRZ is a low-power differential line transceiver for balanced multipoint bus communication, supporting EIA RS-485 and RS-422 operation at 250 kbps. The device combines one differential driver and one differential receiver in a 14-lead SOIC package. Its full-duplex architecture supports simultaneous transmission and reception, making it suitable for industrial control networks, building automation, and instrumentation links.

A differential line transceiver is an interface circuit that converts a single-ended logic signal into a balanced differential signal for reliable data transmission over long cables and noisy environments. The ADM489 family belongs to the RS-485 transceiver hierarchy, where the differential driver and receiver improve common-mode noise rejection compared with single-ended communication.

Key electrical characteristics include operation from a 5 V supply, a maximum signaling rate of 250 kbps, and slew-rate-limited driver outputs that reduce harmonic distortion on the bus. The part supports both RS-485 and RS-422 balanced-data standards. Its 14-pin SOIC package is a widely used surface-mount footprint suitable for automated assembly and compact industrial controller designs.

The full-duplex configuration keeps the transmit and receive paths active simultaneously, avoiding the shared-bus turn-around delay required by half-duplex transceivers. This makes the ADM489ABRZ appropriate when continuous monitoring is required during transmission, when a bus node must exchange data independently, or when a point-to-point link uses separate differential pairs for each direction.

Typical applications include industrial RS-485 fieldbus links, factory-floor sensor and actuator networks, building HVAC controls, industrial gateways, test equipment, and remote I/O modules. The 250 kbps rate and 5 V operation align well with moderate-speed control and monitoring networks rather than high-bandwidth data protocols.

When laying out a circuit, route the driver and receiver differential pairs as controlled-impedance traces and keep the bus-side connections short and symmetrical. Provide the interface's required bypass capacitance at the supply pins and connect unused inputs to defined logic levels rather than leaving them floating. Confirm termination, biasing, and grounding against the selected network topology.

This page consolidates the family-level electrical positioning, package information, cross-reference candidates, and practical interface-layout guidance to support faster component selection and PCB planning.

Drop-in alternatives for ADM489ABRZ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with ADM489ABRZ (same form factor and footprint).

ADM489ARZ

✅ Drop-In
Analog Devices
📦 14-lead SOIC
1/1 · Full-duplex differential line transceiver · RS-422, RS-485 · EIA RS-485 and EIA RS-422 · 4.5 V to 5.5 V · 250 kbps · Slew-rate limited · +/-10%

Contact for price

View Datasheet →

ADM489ABRZ Specifications

Product Type Differential Line Transceiver
Standards Compliance EIA RS-485 and RS-422
Operating Supply Voltage 5 V
Maximum Data Rate 250 kbps
Duplex Mode Full Duplex
Driver Count 1
Receiver Count 1
Output Driver Type Slew Rate Limited
Transmission Type Balanced Differential
Bus Configuration Multipoint Bus Transmission Line
Power Class Low Power
Package 14-lead SOIC
Mounting Type Surface Mount

ADM489ABRZ 14-lead soic Pin Configuration Guide

Pin configuration for ADM489ABRZ (14-lead soic package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

14-lead soic package pinout diagram for ADM489ABRZ

No detailed pinout data available for ADM489ABRZ.

Refer to the datasheet for full pin configuration.

Typical Applications

ADM489ABRZ is suitable for 3 applications: Embedded Systems, IoT Devices, Industrial Control.

🧩

Embedded Systems

Core processing in embedded applications using ADM489ABRZ.

🌐

IoT Devices

Smart connected devices powered by ADM489ABRZ.

🏭

Industrial Control

Automation and control systems using ADM489ABRZ.

What is the ADM489ABRZ used for?
The ADM489ABRZ is a low-power differential line transceiver for balanced multipoint-bus communication, with one driver and one receiver in a 14-lead SOIC package. According to the Analog Devices ADM489 product page, it is intended for EIA RS-485 and RS-422 data transmission. Its full-duplex operation allows transmit and receive paths to work simultaneously, making it suitable for industrial control links, building automation equipment, and remote instrumentation.
What is the maximum data rate of the ADM489ABRZ?
The ADM489ABRZ supports a maximum data rate of 250 kbps. Analog Devices describes the ADM489 family as a low-power differential transceiver with a slew-rate-limited driver for reduced bus disturbance. This rate is appropriate for industrial control and monitoring networks that carry moderate-speed commands, sensor readings, and status data. Faster protocols or longer cable runs require a transceiver specifically qualified for the corresponding edge rate and reach.
Which communication standards does the ADM489ABRZ support?
The ADM489ABRZ supports balanced differential transmission under the EIA RS-485 and RS-422 standards. These standards are identified on the Analog Devices ADM489 product page. RS-485 is widely used for multipoint industrial buses, while RS-422 commonly serves balanced point-to-point links. Because this part is full duplex, it maintains separate transmit and receive paths instead of sharing one conductor pair as a half-duplex transceiver does.
What is the difference between full-duplex and half-duplex RS-485 transceivers?
A full-duplex RS-485 transceiver can transmit and receive simultaneously, whereas a half-duplex transceiver shares one differential pair for both directions. The ADM489ABRZ is full duplex and therefore does not require the driver to be disabled while its receiver listens. This simplifies bus arbitration logic and supports continuous monitoring, although it uses separate driver and receiver pairs and can require more board space than a half-duplex implementation.
What supply voltage does the ADM489ABRZ use?
The ADM489ABRZ operates from a 5 V supply. The 5 V rating is shown in the Mouser listing for this part, which identifies it as a 5 V, 250 kbps, full-duplex RS-422/RS-485 interface IC. Place the required bypass capacitor close to the device supply pin and keep the return path continuous beneath the circuit. Request the current lead time and pricing through the Request a Quote form on this page.
Where can I download the ADM489ABRZ datasheet?
The official ADM489 datasheet and product information are available from the Analog Devices product page linked on this page. The manufacturer document contains the definitive electrical characteristics, recommended application circuit, pin assignments, and full operating details for the ADM489 family. Use that document for layout and design-in work, then use the Request a Quote form on this page for commercial availability, current lead time, and a formal quotation.
Where can I find the ADM489ABRZ pinout?
The ADM489ABRZ pin assignments are published in the pin-configuration section of the Analog Devices ADM489 datasheet. The device uses a 14-lead SOIC package, and the manufacturer diagram identifies the driver, receiver, enable, supply, and ground connections. Do not infer a pinout solely from the package drawing; verify every net against the official pin table before fabrication so that enable polarity and differential signal names are assigned correctly.
Is the ADM489ABRZ a drop-in replacement for an ADM489ARZ?
The ADM489ABRZ and ADM489ARZ belong to the same Analog Devices ADM489 transceiver family and are identified in a published product comparison. Their suitability as a direct substitution depends on the exact device suffix, supply configuration, and operating-temperature grade in the original bill of materials. Confirm those ordering details against the Analog Devices datasheet before treating the two as interchangeable, and verify the PCB footprint against the 14-lead SOIC package.
When should I choose the ADM489ABRZ over a half-duplex RS-485 transceiver?
Choose the ADM489ABRZ when a design must transmit and receive concurrently, needs no shared-bus turn-around interval, or uses separate differential pairs for point-to-point communication. A half-duplex transceiver can be preferable when wiring cost dominates or only one pair of bus wires is available. The ADM489ABRZ is a full-duplex 250 kbps device, so either approach should be selected around network topology rather than speed alone.
Can the ADM489ABRZ be used for RS-422 point-to-point links?
Yes, the ADM489ABRZ is designed to support RS-422 as well as RS-485 balanced transmission. According to the Analog Devices product page, the ADM489 family complies with both EIA standards, while its 5 V supply and 250 kbps rate match conventional industrial point-to-point interfaces. Confirm cable length, termination, and grounding against the application circuit in the manufacturer datasheet.
What are the key specifications of ADM489ABRZ that engineers should know?
The ADM489ABRZ combines a 5 V supply, 250 kbps maximum data rate, one differential driver, one differential receiver, and full-duplex operation in a 14-lead SOIC package. Analog Devices identifies the part as a low-power RS-485/RS-422 transceiver with a slew-rate-limited driver. These core ratings define its position between slow isolated-interface products and high-speed RS-485 transceivers designed for longer distances or faster data links.
What can replace an ADM489ABRZ?
The closest same-family candidate identified for the ADM489ABRZ is the ADM489ARZ from Analog Devices, which appears in a published product comparison. A true drop-in substitution must match the 14-lead SOIC footprint, driver and receiver pin functions, enable logic, supply voltage, and operating-temperature grade. Cross-brand RS-485 transceivers may use the same package but often differ in fail-safe behavior, slew rate, and bus loading, so verify the pinout rather than relying on package size alone.
Is the ADM489ABRZ suitable for industrial factory automation?
The ADM489ABRZ is suitable for factory automation links that operate at 250 kbps or below on balanced RS-485 or RS-422 wiring. Its low-power, full-duplex architecture supports separate command and response paths in controller, sensor-hub, and actuator modules. Industrial implementation also requires attention to isolation, surge protection, cable termination, common-mode grounding, and the enclosure environment, none of which are provided by the transceiver alone.
How should an ADM489ABRZ RS-485 board be laid out?
Route the ADM489ABRZ differential pairs as controlled-impedance traces, keep driver and receiver traces closely coupled, and avoid crossing digital return paths on the bus side. Place supply bypass capacitance at the device pins and maintain a continuous ground reference beneath the interface. The manufacturer application circuit should guide decoupling, bus-side component placement, and protection selection, particularly near external cable connectors.
Where can I buy the ADM489ABRZ and what is its lead time?
Use the Request a Quote form on this page to request current ADM489ABRZ pricing, stock confirmation, minimum order quantity, and manufacturing lead time for your required quantity. The form is the direct route for a commercial quotation and avoids reliance on stale catalog pricing. Include your target date, reel or tube packaging preference, and the quantity required so the supplier can confirm the correct supply position.

Engineering reference data for ADM489ABRZ — comparison, design guidance, and compliance information.

Selection Guide

Select the ADM489ABRZ when a design needs a 5 V, 250 kbps RS-485 or RS-422 interface with independent transmit and receive paths. Its full-duplex operation is especially useful where continuous reception, simultaneous data exchange, or point-to-point wiring is required. The ADM489ARZ is the closest same-family candidate for an existing design, but its ordering suffix and temperature-grade details must be verified before substitution. Choose a half-duplex transceiver instead when only one bus pair is available or board area and wiring cost dominate. For any candidate, compare the complete pin table, enable polarity, receiver fail-safe behavior, bus loading, supply range, and package footprint. Protection, isolation, and cable termination remain separate system requirements; the ADM489ABRZ is the balanced line-interface IC at the center of that design.

Comparison with Alternatives

Parameter This Product ADM489ARZ
Brand Analog Devices Analog Devices
Package 14-lead SOIC 14-lead SOIC
Transceiver Configuration 1 Driver / 1 Receiver 1 Driver / 1 Receiver
Standards RS-485 and RS-422 RS-485 and RS-422
Maximum Data Rate 250 kbps 250 kbps
Operating Supply Voltage 5 V 5 V
Duplex Mode Full Duplex Full Duplex
Driver Output Slew Rate Limited Slew Rate Limited
Power Class Low Power Low Power
Bus Topology Balanced multipoint bus Balanced multipoint bus

Key Differentiators

  • Concurrent full-duplex communication (vs ADM489ARZ)
  • Moderate-speed industrial bus operation (vs ADM489ARZ)
  • Reduced bus-edge disturbance (vs ADM489ARZ)

Design Notes

Route each differential pair with continuous reference to the ground plane and keep the driver outputs and receiver inputs away from switching nodes. Avoid routing balanced signals beneath regulators, clock sources, and high-current switching elements. Where the transceiver connects to an external connector, place protection and bus-side termination ahead of the IC so surge current is diverted away from sensitive inputs.

Place the manufacturer-recommended bypass capacitor directly across the device supply pins with a short, low-inductance return to ground. Keep the 5 V supply path free of narrow necks and maintain a low-impedance ground connection beneath the package. Validate the supply at the transceiver during cable load changes because a drooping rail can reduce receiver noise margin or disturb the slew-rate-limited driver output.

Do not treat a shared SOIC footprint as proof that every RS-485 transceiver is interchangeable. Full-duplex devices require separate transmit and receive differential pairs, and enable pins, fail-safe inputs, receiver polarity, and bus termination can differ between families. Check the ADM489 manufacturer pin table against the candidate device before approving a substitution, and do not leave unused logic inputs floating.

The slew-rate-limited driver reduces edge-rate harmonics, but cable routing still determines much of the radiated noise. Use controlled-impedance pair geometry, avoid large stubs, and apply termination only where the network topology requires it. For long or industrial cables, combine the interface with appropriately rated surge and ESD protection rather than assuming the transceiver alone can withstand connector transients.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The device is an industrial interface IC rather than an AEC-Q100 automotive-qualified product. Confirm material-compliance declarations with the manufacturer for the exact ordering code.

Data verified on: 2026-11-14 — data verified and curated by XAIPART's component engineering team

Related Searches

ADM489ABRZ datasheet ADM489ABRZ pinout ADM489ABRZ datasheet pdf Analog Devices ADM489ABRZ ADM489ABRZ equivalent ADM489ABRZ replacement ADM489ABRZ cross reference ADM489ABRZ vs ADM489ARZ ADM489ABRZ 250kbps full duplex ADM489ABRZ 14-SOIC pinout ADM489ABRZ RS-485 industrial bus ADM489ABRZ price ADM489ABRZ stock buy ADM489ABRZ online what can replace ADM489ABRZ

Related Components & Terms

Analog Devices ADM489ABRZ ADM489ARZ ADM489 RS-485 RS-422 EIA RS-485 EIA RS-422 differential line transceiver full-duplex transceiver balanced differential transmission multipoint bus slew rate limited low-power transceiver 250 kbps 5 V supply 14-lead SOIC SOIC package family surface mount industrial automation building automation factory automation RS-485 termination differential impedance
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details