ADM489ABRZ - 250kbps Full-Duplex RS-485 IC | Analog Devices
MPN: ADM489ABRZ ✓ Hoạt độngADM489ABRZ Tóm tắt
A differential line transceiver is an interface circuit that converts a single-ended logic signal into a balanced differential signal for reliable data transmission over long cables and noisy environments. The ADM489 family belongs to the RS-485 transceiver hierarchy, where the differential driver and receiver improve common-mode noise rejection compared with single-ended communication.
Key electrical characteristics include operation from a 5 V supply, a maximum signaling rate of 250 kbps, and slew-rate-limited driver outputs that reduce harmonic distortion on the bus. The part supports both RS-485 and RS-422 balanced-data standards. Its 14-pin SOIC package is a widely used surface-mount footprint suitable for automated assembly and compact industrial controller designs.
The full-duplex configuration keeps the transmit and receive paths active simultaneously, avoiding the shared-bus turn-around delay required by half-duplex transceivers. This makes the ADM489ABRZ appropriate when continuous monitoring is required during transmission, when a bus node must exchange data independently, or when a point-to-point link uses separate differential pairs for each direction.
Typical applications include industrial RS-485 fieldbus links, factory-floor sensor and actuator networks, building HVAC controls, industrial gateways, test equipment, and remote I/O modules. The 250 kbps rate and 5 V operation align well with moderate-speed control and monitoring networks rather than high-bandwidth data protocols.
When laying out a circuit, route the driver and receiver differential pairs as controlled-impedance traces and keep the bus-side connections short and symmetrical. Provide the interface's required bypass capacitance at the supply pins and connect unused inputs to defined logic levels rather than leaving them floating. Confirm termination, biasing, and grounding against the selected network topology.
This page consolidates the family-level electrical positioning, package information, cross-reference candidates, and practical interface-layout guidance to support faster component selection and PCB planning.
Bộ thay thế dễ dàng lắp đặt cho ADM489ABRZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADM489ABRZ (cùng hình factor và footprint).
ADM489ARZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADM489ABRZ Thông số kỹ thuật
| Product Type | Differential Line Transceiver |
| Standards Compliance | EIA RS-485 and RS-422 |
| Điện áp cung cấp hoạt động | 5 V |
| Maximum Data Rate | 250 kbps |
| Duplex Mode | Full Duplex |
| Driver Count | 1 |
| Receiver Count | 1 |
| Output Driver Type | Slew Rate Limited |
| Transmission Type | Balanced Differential |
| Bus Configuration | Multipoint Bus Transmission Line |
| Power Class | Low Power |
| Hộp | 14-lead SOIC |
| Kiểu lắp đặt | Surface Mount |
Hướng dẫn cấu hình chân ADM489ABRZ 14-lead soic
Cấu hình chân cho ADM489ABRZ (14-lead soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADM489ABRZ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADM489ABRZ phù hợp cho 3 Áp dụngs: Hệ thống tích hợp, Máy thiết bị IoT, Điều khiển công nghiệp.
Hệ thống tích hợp
Xử lý trung tâm trong các ứng dụng tích hợp sử dụng ADM489ABRZ.
Máy thiết bị IoT
Máy thiết bị kết nối thông minh được cung cấp bởi ADM489ABRZ.
Điều khiển công nghiệp
Hệ thống tự động hóa và điều khiển sử dụng ADM489ABRZ.
Dữ liệu tham khảo kỹ thuật cho ADM489ABRZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADM489ARZ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 14-lead SOIC | 14-lead SOIC |
| Transceiver Configuration | 1 Driver / 1 Receiver | 1 Driver / 1 Receiver |
| Standards | RS-485 and RS-422 | RS-485 and RS-422 |
| Maximum Data Rate | 250 kbps | 250 kbps |
| Operating Supply Voltage | 5 V | 5 V |
| Duplex Mode | Full Duplex | Full Duplex |
| Driver Output | Slew Rate Limited | Slew Rate Limited |
| Power Class | Low Power | Low Power |
| Bus Topology | Balanced multipoint bus | Balanced multipoint bus |
Bảo phân biệt quan trọng
- Concurrent full-duplex communication (vsADM489ARZ)
- Moderate-speed industrial bus operation (vsADM489ARZ)
- Reduced bus-edge disturbance (vsADM489ARZ)
Ghi chú thiết kế
Route each differential pair with continuous reference to the ground plane and keep the driver outputs and receiver inputs away from switching nodes. Avoid routing balanced signals beneath regulators, clock sources, and high-current switching elements. Where the transceiver connects to an external connector, place protection and bus-side termination ahead of the IC so surge current is diverted away from sensitive inputs.
Place the manufacturer-recommended bypass capacitor directly across the device supply pins with a short, low-inductance return to ground. Keep the 5 V supply path free of narrow necks and maintain a low-impedance ground connection beneath the package. Validate the supply at the transceiver during cable load changes because a drooping rail can reduce receiver noise margin or disturb the slew-rate-limited driver output.
Do not treat a shared SOIC footprint as proof that every RS-485 transceiver is interchangeable. Full-duplex devices require separate transmit and receive differential pairs, and enable pins, fail-safe inputs, receiver polarity, and bus termination can differ between families. Check the ADM489 manufacturer pin table against the candidate device before approving a substitution, and do not leave unused logic inputs floating.
The slew-rate-limited driver reduces edge-rate harmonics, but cable routing still determines much of the radiated noise. Use controlled-impedance pair geometry, avoid large stubs, and apply termination only where the network topology requires it. For long or industrial cables, combine the interface with appropriately rated surge and ESD protection rather than assuming the transceiver alone can withstand connector transients.
Thông tin tuân thủ
The device is an industrial interface IC rather than an AEC-Q100 automotive-qualified product. Confirm material-compliance declarations with the manufacturer for the exact ordering code.