ADM489ABRZ - 250kbps Full-Duplex RS-485 IC | Analog Devices
部品番号: ADM489ABRZ ✓ 生産中ADM489ABRZ 概要
A differential line transceiver is an interface circuit that converts a single-ended logic signal into a balanced differential signal for reliable data transmission over long cables and noisy environments. The ADM489 family belongs to the RS-485 transceiver hierarchy, where the differential driver and receiver improve common-mode noise rejection compared with single-ended communication.
Key electrical characteristics include operation from a 5 V supply, a maximum signaling rate of 250 kbps, and slew-rate-limited driver outputs that reduce harmonic distortion on the bus. The part supports both RS-485 and RS-422 balanced-data standards. Its 14-pin SOIC package is a widely used surface-mount footprint suitable for automated assembly and compact industrial controller designs.
The full-duplex configuration keeps the transmit and receive paths active simultaneously, avoiding the shared-bus turn-around delay required by half-duplex transceivers. This makes the ADM489ABRZ appropriate when continuous monitoring is required during transmission, when a bus node must exchange data independently, or when a point-to-point link uses separate differential pairs for each direction.
Typical applications include industrial RS-485 fieldbus links, factory-floor sensor and actuator networks, building HVAC controls, industrial gateways, test equipment, and remote I/O modules. The 250 kbps rate and 5 V operation align well with moderate-speed control and monitoring networks rather than high-bandwidth data protocols.
When laying out a circuit, route the driver and receiver differential pairs as controlled-impedance traces and keep the bus-side connections short and symmetrical. Provide the interface's required bypass capacitance at the supply pins and connect unused inputs to defined logic levels rather than leaving them floating. Confirm termination, biasing, and grounding against the selected network topology.
This page consolidates the family-level electrical positioning, package information, cross-reference candidates, and practical interface-layout guidance to support faster component selection and PCB planning.
ドロップイン代替品: ADM489ABRZ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ADM489ABRZ (同一形状・フットプリント).
ADM489ARZ
✅ ドロップイン価格はお問い合わせください
データシートを見る →ADM489ABRZ 仕様
| Product Type | Differential Line Transceiver |
| Standards Compliance | EIA RS-485 and RS-422 |
| 動作電源電圧 | 5 V |
| Maximum Data Rate | 250 kbps |
| Duplex Mode | Full Duplex |
| Driver Count | 1 |
| Receiver Count | 1 |
| Output Driver Type | Slew Rate Limited |
| Transmission Type | Balanced Differential |
| Bus Configuration | Multipoint Bus Transmission Line |
| Power Class | Low Power |
| パッケージ | 14-lead SOIC |
| 実装タイプ | Surface Mount |
ADM489ABRZ 14-lead soic ピン配置ガイド
ADM489ABRZ (14-lead soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: ADM489ABRZ.
詳細は データシート をご参照ください。
主な用途
ADM489ABRZ の用途: 3 件s: 組込みシステム, IoTデバイス, 産業制御.
組込みシステム
ADM489ABRZを使用した組込みアプリケーションのコア処理。
IoTデバイス
ADM489ABRZを搭載したスマートコネクテッドデバイス。
産業制御
ADM489ABRZを使用した自動化および制御システム。
エンジニアリング参考データ: ADM489ABRZ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ADM489ARZ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 14-lead SOIC | 14-lead SOIC |
| Transceiver Configuration | 1 Driver / 1 Receiver | 1 Driver / 1 Receiver |
| Standards | RS-485 and RS-422 | RS-485 and RS-422 |
| Maximum Data Rate | 250 kbps | 250 kbps |
| Operating Supply Voltage | 5 V | 5 V |
| Duplex Mode | Full Duplex | Full Duplex |
| Driver Output | Slew Rate Limited | Slew Rate Limited |
| Power Class | Low Power | Low Power |
| Bus Topology | Balanced multipoint bus | Balanced multipoint bus |
主な差別化要因
- Concurrent full-duplex communication (vs ADM489ARZ)
- Moderate-speed industrial bus operation (vs ADM489ARZ)
- Reduced bus-edge disturbance (vs ADM489ARZ)
設計ノート
Route each differential pair with continuous reference to the ground plane and keep the driver outputs and receiver inputs away from switching nodes. Avoid routing balanced signals beneath regulators, clock sources, and high-current switching elements. Where the transceiver connects to an external connector, place protection and bus-side termination ahead of the IC so surge current is diverted away from sensitive inputs.
Place the manufacturer-recommended bypass capacitor directly across the device supply pins with a short, low-inductance return to ground. Keep the 5 V supply path free of narrow necks and maintain a low-impedance ground connection beneath the package. Validate the supply at the transceiver during cable load changes because a drooping rail can reduce receiver noise margin or disturb the slew-rate-limited driver output.
Do not treat a shared SOIC footprint as proof that every RS-485 transceiver is interchangeable. Full-duplex devices require separate transmit and receive differential pairs, and enable pins, fail-safe inputs, receiver polarity, and bus termination can differ between families. Check the ADM489 manufacturer pin table against the candidate device before approving a substitution, and do not leave unused logic inputs floating.
The slew-rate-limited driver reduces edge-rate harmonics, but cable routing still determines much of the radiated noise. Use controlled-impedance pair geometry, avoid large stubs, and apply termination only where the network topology requires it. For long or industrial cables, combine the interface with appropriately rated surge and ESD protection rather than assuming the transceiver alone can withstand connector transients.
コンプライアンス情報
The device is an industrial interface IC rather than an AEC-Q100 automotive-qualified product. Confirm material-compliance declarations with the manufacturer for the exact ordering code.