ADM489ABRZ - 250kbps Full-Duplex RS-485 IC | Analog Devices
料号: ADM489ABRZ ✓ 量产中ADM489ABRZ 概述
A differential line transceiver is an interface circuit that converts a single-ended logic signal into a balanced differential signal for reliable data transmission over long cables and noisy environments. The ADM489 family belongs to the RS-485 transceiver hierarchy, where the differential driver and receiver improve common-mode noise rejection compared with single-ended communication.
Key electrical characteristics include operation from a 5 V supply, a maximum signaling rate of 250 kbps, and slew-rate-limited driver outputs that reduce harmonic distortion on the bus. The part supports both RS-485 and RS-422 balanced-data standards. Its 14-pin SOIC package is a widely used surface-mount footprint suitable for automated assembly and compact industrial controller designs.
The full-duplex configuration keeps the transmit and receive paths active simultaneously, avoiding the shared-bus turn-around delay required by half-duplex transceivers. This makes the ADM489ABRZ appropriate when continuous monitoring is required during transmission, when a bus node must exchange data independently, or when a point-to-point link uses separate differential pairs for each direction.
Typical applications include industrial RS-485 fieldbus links, factory-floor sensor and actuator networks, building HVAC controls, industrial gateways, test equipment, and remote I/O modules. The 250 kbps rate and 5 V operation align well with moderate-speed control and monitoring networks rather than high-bandwidth data protocols.
When laying out a circuit, route the driver and receiver differential pairs as controlled-impedance traces and keep the bus-side connections short and symmetrical. Provide the interface's required bypass capacitance at the supply pins and connect unused inputs to defined logic levels rather than leaving them floating. Confirm termination, biasing, and grounding against the selected network topology.
This page consolidates the family-level electrical positioning, package information, cross-reference candidates, and practical interface-layout guidance to support faster component selection and PCB planning.
直接替换替代料: ADM489ABRZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
ADM489ABRZ 规格参数
| Product Type | Differential Line Transceiver |
| Standards Compliance | EIA RS-485 and RS-422 |
| 工作电源电压 | 5 V |
| Maximum Data Rate | 250 kbps |
| Duplex Mode | Full Duplex |
| Driver Count | 1 |
| Receiver Count | 1 |
| Output Driver Type | Slew Rate Limited |
| Transmission Type | Balanced Differential |
| Bus Configuration | Multipoint Bus Transmission Line |
| Power Class | Low Power |
| 封装 | 14-lead SOIC |
| 安装类型 | Surface Mount |
ADM489ABRZ 14-lead soic 引脚配置指南
ADM489ABRZ(14-lead soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ADM489ABRZ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADM489ABRZ 适用于 3 应用s: 嵌入式系统, 物联网设备, 工业控制.
嵌入式系统
使用 ADM489ABRZ 在嵌入式应用中进行核心处理。
物联网设备
由 ADM489ABRZ 驱动的智能联网设备。
工业控制
使用 ADM489ABRZ 的自动化和控制系统。
工程参考数据: ADM489ABRZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADM489ARZ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 14-lead SOIC | 14-lead SOIC |
| Transceiver Configuration | 1 Driver / 1 Receiver | 1 Driver / 1 Receiver |
| Standards | RS-485 and RS-422 | RS-485 and RS-422 |
| Maximum Data Rate | 250 kbps | 250 kbps |
| Operating Supply Voltage | 5 V | 5 V |
| Duplex Mode | Full Duplex | Full Duplex |
| Driver Output | Slew Rate Limited | Slew Rate Limited |
| Power Class | Low Power | Low Power |
| Bus Topology | Balanced multipoint bus | Balanced multipoint bus |
关键差异点
- Concurrent full-duplex communication (对比 ADM489ARZ)
- Moderate-speed industrial bus operation (对比 ADM489ARZ)
- Reduced bus-edge disturbance (对比 ADM489ARZ)
设计说明
Route each differential pair with continuous reference to the ground plane and keep the driver outputs and receiver inputs away from switching nodes. Avoid routing balanced signals beneath regulators, clock sources, and high-current switching elements. Where the transceiver connects to an external connector, place protection and bus-side termination ahead of the IC so surge current is diverted away from sensitive inputs.
Place the manufacturer-recommended bypass capacitor directly across the device supply pins with a short, low-inductance return to ground. Keep the 5 V supply path free of narrow necks and maintain a low-impedance ground connection beneath the package. Validate the supply at the transceiver during cable load changes because a drooping rail can reduce receiver noise margin or disturb the slew-rate-limited driver output.
Do not treat a shared SOIC footprint as proof that every RS-485 transceiver is interchangeable. Full-duplex devices require separate transmit and receive differential pairs, and enable pins, fail-safe inputs, receiver polarity, and bus termination can differ between families. Check the ADM489 manufacturer pin table against the candidate device before approving a substitution, and do not leave unused logic inputs floating.
The slew-rate-limited driver reduces edge-rate harmonics, but cable routing still determines much of the radiated noise. Use controlled-impedance pair geometry, avoid large stubs, and apply termination only where the network topology requires it. For long or industrial cables, combine the interface with appropriately rated surge and ESD protection rather than assuming the transceiver alone can withstand connector transients.
合规信息
The device is an industrial interface IC rather than an AEC-Q100 automotive-qualified product. Confirm material-compliance declarations with the manufacturer for the exact ordering code.