CD4029BEX - 4-Bit Binary/BCD Up/Down Counter, 16-PDIP | Texas Instruments
MPN: CD4029BEX ✓ ActiveCD4029BEX Overview
A counter integrated circuit is a digital logic device that accumulates clock events and presents the running total as a binary-weighted output word. A binary counter advances one count per clock edge with each output toggling at a different power of two, while a BCD-decade counter advances through the ten states 0 to 9, which is the format required by most seven-segment displays. Up/down counters add a direction control so the same silicon can count toward a preset limit or count down from it. In the power-management and digital-control hierarchy, the CD4029BEX sits in the logic IC family, specifically the counters and dividers class of CMOS integrated circuits.
The standout feature of this part is the parallel JAM architecture: each of the four jam inputs can asynchronously force its corresponding Q output high or low, independent of the clock, which allows an external controller to load a starting value or capture a count instantly. Look-ahead carry means the CARRY OUT signal is generated in advance of the clock edge, so cascaded counters can be chained without ripple delay. The BINARY/DECADE select pin switches the counting base in one part, and the UP/DOWN pin sets the counting direction, giving a single package both divide-by-16 binary and divide-by-10 decade behavior.
Internally the CD4029BEX is a static CMOS design with complementary MOS inputs, so all inputs may be driven from either CMOS or TTL levels as long as voltage thresholds are respected. The single clock line means there is no separate preset clock, which simplifies synchronisation to one system clock domain and prevents race conditions between a preset pulse and a clock edge that separate clocked counters exhibit. Because the outputs are flip-flop based rather than purely combinational, the Q outputs change only on the active clock edge, giving clean, glitch-free output transitions for display and datapath use.
Typical applications include divide-by-16 and divide-by-10 frequency dividers, decade counters driving seven-segment LED displays, programmable timing and sequencing modules, batch and piece counting in industrial machinery, position counting in stepper motor indexers, and general ripple-counter chains in legacy control logic. The BCD-decade mode is especially useful for direct display interfacing without a binary-to-BCD conversion stage.
When designing around the CD4029BEX, tie all unused CMOS inputs to a defined logic level rather than leaving them floating, because a floating CMOS input can sit in the linear region of the transfer characteristic and draw unpredictable current. Drive JAM inputs from a source that is guaranteed valid whenever the count must be held, and remember that the CARRY OUT pin is an output only, so it must not be used as a clock enable by driving it. Use the PRE-SET ENABLE pin rather than toggling JAM pins asynchronously if the design needs a repeatable, glitch-free load of the starting count.
This page combines the manufacturer pin description and function outline, package details, available supply and lifecycle information, and structured drop-in alternatives with practical design notes so engineers can qualify a replacement quickly instead of searching manually through generic cross-reference tables.
Drop-in alternatives for CD4029BEX — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with CD4029BEX (same form factor and footprint) — differing in Counter Type, Logic Family, Mounting Type, Package, Carry Function.
CD4029BE
✅ Drop-InContact for price
View Datasheet →CD4029BPW
✅ Drop-InContact for price
View Datasheet →MC14029BD
✅ Drop-InContact for price
View Datasheet →HCF4029BE
✅ Drop-In📋 Reference alternative (not in catalog)
CD4029BEX
✅ Drop-InContact for price
View Datasheet →CD4029BEX Maximum Ratings & Electrical Characteristics
| Logic Family | CMOS CD4000 series |
| Counter Type | 4-bit binary / BCD-decade up/down counter |
| Number of Counting Elements | 1 |
| Number of Count Stages | 4 |
| Counting Direction | Up/Down selectable (UP/DOWN input) |
| Clock Edge | Positive edge |
| Clock Inputs | 1 (single CLOCK) |
| Carry Function | Look-ahead carry in both counting modes (CARRY IN and CARRY OUT) |
| Mode Control | BINARY/DECADE select input |
| Jam Inputs | 4 individual JAM signals (JAM1 to JAM4) |
| Preset Control | PRE-SET ENABLE input |
| Number of Outputs | 5 (Q1, Q2, Q3, Q4, CARRY OUT) |
| Logic Type | CMOS, static (flip-flop based outputs) |
| Package | 16-pin PDIP (EX suffix) |
| Mounting Type | Through-hole (THT) |
| Datasheet Document | CD4029B TYPES datasheet, Texas Instruments (document number not stated) |
CD4029BEX Pin Configuration
| Pin 1 | CLOCK — Positive-edge count input |
| Pin 2 | CARRY IN — Clock enable / look-ahead carry input |
| Pin 3 | BINARY/DECADE — Counting base select input |
| Pin 4 | UP/DOWN — Counting direction select input |
| Pin 5 | PRE-SET ENABLE — Enables parallel load of the jam inputs |
| Pin 6 | JAM1 — Asynchronous jam input for Q1 |
| Pin 7 | JAM2 — Asynchronous jam input for Q2 |
| Pin 8 | JAM3 — Asynchronous jam input for Q3 |
| Pin 9 | JAM4 — Asynchronous jam input for Q4 |
| Pin 10 | Q1 — Counter output, weight 1 |
| Pin 11 | Q2 — Counter output, weight 2 |
| Pin 12 | Q3 — Counter output, weight 4 |
| Pin 13 | Q4 — Counter output, weight 8 |
| Pin 14 | CARRY OUT — Look-ahead carry output |
| Pin 15 | VDD — Positive supply |
| Pin 16 | VSS — Ground |
Typical Applications
CD4029BEX is suitable for 6 applications: Binary and Decade Frequency Divider, Seven-Segment Display Counter, Industrial Batch and Piece Counter, Programmable Timer and Sequence Controller, Stepper Motor Index and Position Counter, Legacy Ripple Counter Chain and Clock Divider.
Binary and Decade Frequency Divider
The CD4029BEX divides an incoming clock by 16 in binary mode or by 10 in BCD-decade mode, which makes it a compact frequency divider for clock conditioning and rate reduction. With the BINARY/DECADE input tied low or high respectively, the single positive-edge CLOCK input drives four flip-flop stages, and the Q outputs provide weighted taps of 1, 2, 4 and 8. The CARRY OUT signal is produced with look-ahead carry in both counting modes, so cascaded stages advance without ripple delay. This suits timer base generation, clock tree conditioning, and event-rate reduction in instrumentation where a divided, jitter-free square wave is required at the output.
Recommended
Seven-Segment Display Counter
In BCD-decade mode the CD4029BEX produces the 0 to 9 weighted code that seven-segment display drivers expect, so a decade counter can drive a display without a separate binary-to-BCD conversion stage. The four JAM inputs allow the display to be preset to a known value, and the UP/DOWN input lets the same silicon increment or decrement, which is useful for position indicators and step counters. Because the outputs are flip-flop based, Q1 to Q4 change only on the active clock edge, which keeps the display free of decode glitches while the count is incrementing. Typical uses are bench timers, batch counters and panel-mounted production counters.
Recommended
Industrial Batch and Piece Counter
The CD4029BEX suits machine-mounted counting tasks because its four asynchronous JAM inputs let a sensor or controller capture and hold a count without waiting for a clock edge, and the PRE-SET ENABLE input loads a known starting value. With the CLOCK driven by a sensor or encoder-derived pulse train, the device counts parts, cycles or actuations and raises CARRY OUT at the programmed decade or binary limit. The look-ahead carry keeps the boundary signal clean for direct connection to downstream annunciators or relay drivers. For factory equipment the temperature grade of the fitted suffix must match the enclosure environment, and unused CMOS inputs should be tied to defined levels.
Recommended
Programmable Timer and Sequence Controller
Using the CD4029BEX in binary mode with the UP/DOWN input fixed gives a 16-state sequence machine, and the BINARY/DECADE input selects between 16-state and 10-state cycles without changing the hardware. The four JAM inputs act as asynchronous preset and reset controls, so a sequencer can jump between states on demand, while CARRY OUT provides a programmable end-of-cycle marker for the next logic stage. This configuration appears in legacy test fixtures, pump and valve rotation controllers, and relay sequencers where a fixed cycle count drives discrete steps. The single CLOCK line keeps the state machine in one clock domain and avoids the race conditions found in dual-clock preset counters.
Recommended
Stepper Motor Index and Position Counter
The CD4029BEX can be driven from an index pulse train to track position, with the count either incrementing on each pulse or decrementing when the direction input is inverted. CARRY OUT then marks every 16th (binary mode) or 10th (decade mode) step, which is convenient for generating coarse homing pulses or repeatable index intervals in a positioner. The four JAM inputs allow the counter to be reloaded to a known coordinate when a home switch is detected, and the synchronous, edge-triggered output behaviour means the position register is read cleanly at a defined instant. This suits hobby and industrial motion controllers, spindle indexers and encoder post-processing logic.
Recommended
Legacy Ripple Counter Chain and Clock Divider
Because the CD4029BEX provides look-ahead carry in both counting modes, several sections can be cascaded to build long dividers without accumulating the ripple delay of a pure toggle-flop chain. The CARRY OUT of one stage drives the CLOCK of the next, producing a clean divide-by-16 or divide-by-10 per section, which is the classic approach for reducing a high-frequency oscillator to a display or processing rate in legacy instrument design. The BINARY/DECADE input lets different sections be set to different bases, so a mixed chain can produce non-standard periods. This remains useful in repair and modernization of older industrial and laboratory equipment.
Recommended
Recommended Products Summary
Engineering reference data for CD4029BEX — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | CD4029BE | CD4029BPW | MC14029B | HCF4029BE | CD4029BEX |
|---|---|---|---|---|---|---|
| Package | PDIP-16 | PDIP-16 - same | PDIP-16 - same | PDIP-16 - same | PDIP-16 - same | PDIP-16 - same (Harris Corporation) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | STMicroelectronics | Harris Corporation |
| Counter Type | 4-bit binary / BCD-decade up/down counter | 4-bit binary / BCD-decade up/down counter | 4-bit binary / BCD-decade up/down counter | 4-bit binary / BCD up/down counter | 4-bit binary / BCD up/down counter | 4-bit binary / BCD-decade up/down counter |
| Number of Count Stages | 4 | 4 | 4 | 4 | 4 | 4 |
| Counting Direction | Up/Down selectable | Up/Down selectable | Up/Down selectable | Up/Down selectable | Up/Down selectable | Up/Down selectable |
| Clock Edge | Positive edge, single CLOCK input | Positive edge, single CLOCK input | Positive edge, single CLOCK input | Positive edge, single CLOCK input | Positive edge, single CLOCK input | Positive edge, single CLOCK input |
| Carry Function | Look-ahead carry in both counting modes | Look-ahead carry in both counting modes | Look-ahead carry in both counting modes | Look-ahead carry | Look-ahead carry | Look-ahead carry in both counting modes |
| Jam Inputs | 4 individual JAM signals | 4 individual JAM signals | 4 individual JAM signals | 4 individual JAM signals | 4 individual JAM signals | 4 individual JAM signals |
| Outputs | Q1, Q2, Q3, Q4, CARRY OUT (5 outputs) | Q1-Q4 plus CARRY OUT | Q1-Q4 plus CARRY OUT | Q1-Q4 plus CARRY OUT | Q1-Q4 plus CARRY OUT | Q1-Q4 plus CARRY OUT |
| Logic Family | CMOS CD4000 series | CMOS CD4000 series | CMOS CD4000 series | CMOS 4000 series | CMOS 4000 series | CMOS CD4000 series |
Key Differentiators
- Single-clock architecture avoids preset and clock race conditions (vs CD4029BE)
- Look-ahead carry in both counting modes speeds up cascaded dividers (vs MC14029B)
- Four asynchronous JAM inputs plus PRE-SET ENABLE give flexible loading (vs HCF4029BE)
- Single-sourcing option versus cross-brand equivalents (vs MC14029B)
Design Notes
Tie every unused CMOS input to a defined logic level. Leaving JAM1 to JAM4, BINARY/DECADE, UP/DOWN or PRE-SET ENABLE floating can drive the input stage into its linear region, producing unpredictable current draw and erratic counter behaviour. Use JAM inputs for immediate asynchronous overrides, and use PRE-SET ENABLE together with the JAM levels when the counter must be reloaded from a known value on the next active clock edge.
Keep the CLOCK trace short and driven by a single source; the CD4029BEX has one clock line and all state changes occur on its active edge, so a long or ring-shaped clock path can pick up noise and cause double counting. Route the four Q outputs away from the clock and JAM nets to limit coupling, and place the supply decoupling capacitor close to the VDD and VSS pins so switching noise on the board is not injected into the counter threshold.
Treat CARRY OUT strictly as an output. It is a look-ahead carry indicator, not a clock enable, so driving it from an external source creates contention on the output stage and unpredictable counting. Use the CARRY IN pin for gating, and connect CARRY OUT of one section only to the CLOCK input of the next section when building a cascaded divider chain, keeping the chain short so that propagation delay through the cascade stays well below the clock period.
Place a 0.1 uF ceramic bypass capacitor between VDD and VSS as close to the device pins as the layout allows, and add bulk decoupling on the shared supply rail if several CD4000 counters are used in the same assembly. CMOS counters draw current mainly at switching edges, so the supply must remain within the rated range at the pins, not just at the regulator output, and the ground return path should be short to avoid injecting supply ripple into the clock threshold.
Compliance Information
The CD4029B family is a mature CMOS logic product; no explicit RoHS, REACH, lead-free or halogen-free declaration was stated on the manufacturer product page for this ordering code, so all entries are recorded as unknown rather than assumed.