Analog Devices

DG211DY+T - Quad SPST CMOS Analog Switch | Analog Devices

MPN: DG211DY+T ✓ Active
+4.5 V to +18 V Vdss 175 ohm maximum Rds(on) 16-SOIC, 0.154 inch (3.90 mm) width Package
MOQ: 1 |

DG211DY+T Overview

The Analog Devices DG211DY+T is a quad single-pole single-throw CMOS analog switch with four normally closed channels, a 175 ohm on-resistance and a 16-SOIC package. The device supports dual supply operation from ±4.5 V to ±18 V, provides glitch-free switching, and is specified over a -40 °C to +85 °C temperature range. Its four-channel architecture allows one package to route four independent analog signals while maintaining a common ground and supply arrangement.

An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The SPST designation means each of the four internal switches has one pole and one throw, while normally closed means each signal is connected to its throw terminal when the control input is inactive. The DG211 belongs to the broader analog-switch hierarchy, alongside multiplexers and demultiplexers, and provides a simple impedance-controlled routing function for test, measurement, and communication equipment.

Key electrical characteristics include a maximum on-resistance of 175 ohm, a maximum turn-on time of 1000 ns, and a maximum turn-off time of 500 ns. Maxim guarantees break-before-make operation, reducing the interval during which old and new signal paths can overlap. The device is also guaranteed not to latch up when its power supplies are disconnected while input signals remain connected, an important robustness characteristic for externally biased analog nodes.

The DG211 uses CMOS switch channels controlled by TTL-compatible control inputs. Its low-leakage design supports precision measurement systems where unintended charge transfer or off-state conduction can corrupt results. Operating from positive and negative rails allows direct connection to bipolar signals without translating every input through separate amplifiers, although common-mode voltage and supply limits must still be respected during layout and system design.

Typical uses include automated test equipment, data-acquisition systems, instrumentation, communication routing, and analog signal multiplexing. A four-channel normally closed switch is particularly useful where a measurement path must remain connected during idle periods and disconnect only when the control logic selects another operating condition.

PCB design should minimize capacitance on control and analog signal traces, keep routing short, and use a continuous ground reference beneath the device where practical. Because the switch is intended for analog signals rather than high-speed digital links, pay close attention to leakage, on-resistance, charge injection, and off-state isolation rather than digital edge-rate limits.

This page consolidates manufacturer specifications, supply-chain observations, drop-in alternatives, and practical design guidance that engineers would otherwise have to assemble from separate datasheets and component listings.

Drop-in alternatives for DG211DY+T — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with DG211DY+T (same form factor and footprint) — differing in Latch-Up Protection, Mounting Type, Package, Switch Configuration, Switching Behavior.

Maxim Integrated
Latch-Up Protection: No latch-up when supplies are disconnected with input signals connected
Mounting Type: Through-hole
Package: 16-pin PDIP
Compare with DG211DY+T →

DG211DY+

✅ Drop-In
📦 16-SOIC
Same 4-circuit, 1:1 normally closed SPST configuration and 175 ohm on-resistance; the order code differs only in the packaging designation.

📋 Reference alternative (not in catalog)

DG211CSE+

✅ Drop-In
📦 16-SOIC
Identical family-level switching function in the same 16-SOIC footprint; the primary distinction is the order code, with reported primary technical parameters consistent.

📋 Reference alternative (not in catalog)

DG211CJ+

✅ Drop-In
Maxim Integrated
📦 16-SOIC
4 channels · 4 × SPST · 1:1 · 175 ohm maximum · CMOS · ±4.5 V to ±18 V · 16-pin PDIP · Through-hole

Contact for price

View Datasheet →

DG211DY

✅ Drop-In
📦 16-SOIC
Cross-brand DG211-family equivalent with the same 4-circuit, 1:1 SPST configuration and 16-SOIC footprint; sourcing status differs from the Analog Devices code.

📋 Reference alternative (not in catalog)

DG211DY-T1

✅ Drop-In
📦 16-SOIC
Cross-brand DG211DY ordering variant in the same 16-SOIC footprint with the same four-channel normally closed SPST architecture; tape-and-reel suffix differs.

📋 Reference alternative (not in catalog)

DG211DY+T Maximum Ratings & Electrical Characteristics

Number of Circuits 4 circuits
Switch Configuration 1:1 SPST
Number of Switches 4 normally closed SPST switches
On-Resistance 175 ohm maximum
Technology CMOS
Positive Supply Range +4.5 V to +18 V
Negative Supply Range -4.5 V to -18 V
Total Supply Range ±4.5 V to ±18 V
Turn-On Time 1000 ns maximum
Turn-Off Time 500 ns maximum
Switching Behavior Break-before-make guaranteed
Switching Transients Glitch-free switching
Latch-Up Protection Guaranteed not to latch up with disconnected supplies and connected input signals
Operating Temperature Range -40 °C to +85 °C
Package 16-SOIC, 0.154 inch (3.90 mm) width
Mounting Type Surface mount
Package Height 1.75 mm maximum

DG211DY+T 1.75 mm maximum Pin Configuration Guide

Pin configuration for DG211DY+T (1.75 mm maximum package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

1.75 mm maximum package pinout diagram for DG211DY+T

No detailed pinout data available for DG211DY+T.

Refer to the datasheet for full pin configuration.

Typical Applications

DG211DY+T is suitable for 6 applications: Automated Test Equipment Signal Routing, Data Acquisition and Multiplexer Front Ends, Precision Instrumentation Signal Isolation, Analog Multiplexing in Communication Equipment, Power-Sequencing and Test-Path Control, Audio and Low-Frequency Analog Routing.

🏭

Automated Test Equipment Signal Routing

The DG211DY+T fits automated test systems that must connect and isolate several analog measurement channels while preserving a defined default connection. Its four normally closed SPST paths operate from ±4.5 V to ±18 V, and the guaranteed break-before-make behavior prevents an instantaneous overlap between old and new routes. With a maximum on-resistance of 175 ohm and turn-off time of 500 ns, the device is appropriate for general-purpose, low-to-moderate-frequency instrumentation rather than high-bandwidth signal chains. Design the fixture interface around the control polarity and verify leakage and charge injection when the measured node has high source impedance.

📊

Data Acquisition and Multiplexer Front Ends

The DG211DY+T can connect multiple analog inputs to a shared measurement chain in data-acquisition equipment. Four normally closed channels reduce the component count compared with four separate single switches, while the 16-SOIC footprint keeps routing manageable on a dense measurement board. The 1000 ns maximum turn-on time is short compared with many measurement settling intervals, but switch on-resistance, leakage, off-state isolation, and injected charge can dominate accuracy at high input impedance. Use the device for moderate-bandwidth analog multiplexing and follow the manufacturer pin configuration when arranging source, drain, control, and supply nets.

🔧

Precision Instrumentation Signal Isolation

The DG211DY+T is useful in instrumentation that needs a normally connected path during idle conditions and deliberate disconnection for calibration or fault isolation. Its CMOS channels operate across ±4.5 V to ±18 V rails, and the manufacturer guarantees latch-up resistance when supplies are removed while input signals remain present. That behavior improves robustness in systems where external test fixtures can drive an input after the board is unpowered. For high-accuracy measurements, evaluate leakage and off-state isolation in addition to the 175 ohm maximum on-resistance, and keep the analog routing away from high-speed switching nodes.

🌐

Analog Multiplexing in Communication Equipment

The DG211DY+T can implement four independent analog routes in communication and interface equipment where a compact, low-frequency multiplexer is sufficient. The normally closed configuration keeps each path connected until its control input changes state, and the specified 1000 ns turn-on and 500 ns turn-off times support straightforward control sequencing. The ±4.5 V to ±18 V supply capability suits both positive-only and split-rail implementations. Designers should preserve the guaranteed break-before-make behavior, control trace impedance, and supply sequencing, especially when the routed signals exceed the logic levels used to control the switch.

⚡

Power-Sequencing and Test-Path Control

The DG211DY+T can disconnect a powered subsystem from a common test node while leaving other channels in their default state. Its latch-up guarantee provides useful protection when supplies are removed before the routed signal, and the guaranteed break-before-make transition avoids an uncontrolled interval in which two paths could overlap. This makes the switch useful in power-sequencing and isolation test boards. Validate the exact logic levels, supply ramps, and maximum analog-node voltage in the manufacturer data sheet, and use the Request a Quote form on this page to confirm availability for production builds.

🎧

Audio and Low-Frequency Analog Routing

The DG211DY+T can route four low-frequency analog signals in audio equipment, control panels, or mixed-signal modules where a normally closed default connection is preferred. The 175 ohm maximum on-resistance is acceptable for many low-impedance audio paths, while glitch-free operation helps reduce visible switching disturbances under valid operating conditions. A dual supply from ±4.5 V to ±18 V allows the switch to handle bipolar control or monitor signals directly. Because the part is not specified as a high-speed audio multiplexer, verify channel bandwidth, off-state isolation, and charge injection against the source impedance and signal quality requirements.

What is the DG211DY+T and what does it do?
The DG211DY+T is a quad normally closed SPST CMOS analog switch from Analog Devices. It provides four independent 1:1 signal paths, each with a maximum on-resistance of 175 ohm, and operates from ±4.5 V to ±18 V in a 16-SOIC package. According to the manufacturer DG211 data sheet, the device features glitch-free switching, guaranteed break-before-make operation, and a -40 °C to +85 °C operating range.
What is the on-resistance of the DG211DY+T?
The DG211DY+T has a maximum on-resistance of 175 ohm. This specification is listed for the 16-SOIC DG211DY+ device and identifies it as a 4-circuit, 1:1 CMOS analog switch. Because the switch is normally closed, the connected signal path presents this resistance while the control input is inactive. Leakage and off-state isolation values should be checked against the manufacturer data sheet for the specific test conditions.
How fast does the DG211DY+T switch?
The DG211DY+T has a maximum turn-on time of 1000 ns and a maximum turn-off time of 500 ns. The manufacturer DG211 data sheet also states that break-before-make operation is guaranteed, preventing the incoming and outgoing signal paths from being closed simultaneously during a transition. This makes the device suitable for analog routing where control timing must not create a momentary short between channels.
Which power supplies does the DG211DY+T require?
The DG211DY+T operates with positive and negative supply rails from ±4.5 V to ±18 V. The manufacturer describes the DG211 as a CMOS switch that can be continuously operated across this dual-rail range and guarantees that it will not latch up if the supplies are disconnected while input signals remain connected. Use the complete power-rail and control-input limits from the data sheet when planning sequencing.
Is the DG211DY+T normally open or normally closed?
The DG211DY+T is normally closed, meaning each of its four SPST channels connects the input terminal to the output terminal when its control input is inactive. The DG201A and DG211 families are identified as normally closed quad SPST analog switches by the manufacturer. This behavior is useful in measurement systems where the signal path should remain connected during idle intervals.
Where can I download the DG211DY+T datasheet PDF?
The official DG211 product page on Analog Devices provides the manufacturer data sheet and product documentation for the DG211 family, including DG211DY+ and DG211DY+T orderable variants. The DG211DY+T is a 16-SOIC ordering code for the tape-and-reel form of DG211DY+. Use the pin-description table in that document when assigning PCB nets and checking control polarity.
Where can I find the DG211DY+T pinout?
The DG211DY+T pinout is documented in the pin-configuration section of the manufacturer DG211 data sheet. The device uses a 16-SOIC package with four normally closed SPST channels and separate positive and negative supply connections. Use the manufacturer pin-description table as the authoritative source for control inputs, source and drain terminals, supply rails, and any exposed-pad or unused-pin assignments.
What is the best drop-in replacement for the DG211DY+T?
The closest drop-in choices identified for the DG211DY+T are the same-family DG211DY+, DG211CSE+, and DG211CJ+ devices in a 16-SOIC package, plus the Vishay DG211DY and DG211DY-T1 versions. Compatibility depends on the required temperature grade, supply range, tape-and-reel format, and procurement conditions. Confirm the control polarity and pin assignment in the manufacturer data sheet before replacing an assembled design.
Can the DG211CSE+ replace the DG211DY+T?
The DG211CSE+ is a close functional replacement for the DG211DY+T because both are 16-SOIC DG211-family quad SPST switches, and comparison data reports consistent principal technical parameters. The practical difference is the order code and associated grade or packaging designation. Confirm the operating-temperature grade and the pin configuration before treating the two devices as interchangeable in every application.
Is the DG211DY+T the same as DG211CJ+?
The DG211DY+T and DG211CJ+ are closely related DG211-family switches with four normally closed SPST channels and a 16-SOIC package, and one comparison source reports no measurable difference in their primary technical parameters. They still have different order codes, so the temperature-grade and packaging requirements associated with each code must be verified before substitution. Use the Request a Quote form on this page to confirm current sourcing for either device.
What is the best Vishay equivalent for the DG211DY+T?
The Vishay Siliconix DG211DY and DG211DY-T1 are the closest cross-brand alternatives identified for the DG211DY+T because they are DG211-family quad SPST analog switches offered in the same 16-pin SOIC footprint. The suffix indicates ordering or packaging differences, while the underlying DG211 function provides normally closed channels. Verify temperature grade, on-resistance, and tape orientation before production substitution.
When should I choose the DG211DY+T instead of another DG211 variant?
Choose the DG211DY+T when you need four normally closed analog channels, a ±4.5 V to ±18 V supply range, a -40 °C to +85 °C industrial temperature range, and tape-and-reel production packaging. Select another code when a different temperature grade, package option, or sourcing arrangement is required. Because the family shares a common footprint, confirm the exact ordering-code requirements during design release.
Is the DG211DY+T suitable for test and measurement equipment?
The DG211DY+T is suitable for test and measurement equipment that needs to route several low-frequency analog signals through a compact, controlled interface. Its four normally closed channels, 175 ohm maximum on-resistance, and 1000 ns maximum turn-on time support general-purpose analog routing. High-impedance sensing, precision settling, and calibration accuracy still depend on leakage, charge injection, and the complete application bandwidth.
How do I reduce switching transients with the DG211DY+T?
Use the DG211DY+T only within its specified analog and control-signal limits, because the manufacturer rates the device for glitch-free operation under valid electrical conditions. Keep control traces short, provide a stable ground reference, and avoid routing sensitive nodes beside control lines. For very high-impedance or precision measurements, evaluate leakage and charge injection because the switching specification alone does not determine measurement error.
Where can I buy the DG211DY+T and what is its lead time?
Use the Request a Quote form on this page to request current availability, pricing, and lead time for the DG211DY+T. The manufacturer lists the DG211 family as production, but inventory and lead time can change with demand, packaging, and regional distribution. Include your required quantity, target date, and shipment destination in the quotation request for the most useful response.

Engineering reference data for DG211DY+T — comparison, design guidance, and compliance information.

Selection Guide

Choose the DG211DY+T for new designs that require four normally closed analog channels, ±4.5 V to ±18 V operation, and a -40 °C to +85 °C temperature range. DG211DY+ is the closest ordering-code alternative when the required packaging form differs. DG211CSE+ and DG211CJ+ provide the same 16-SOIC DG211-family footprint, but their order-code temperature and packaging designations must be checked before substitution. The Vishay DG211DY and DG211DY-T1 are cross-brand alternatives for supply diversification, subject to confirmation of on-resistance, temperature grade, control polarity, and tape orientation. The DG211 is intended for general-purpose analog routing rather than high-speed video or RF switching. For precision measurement, evaluate leakage, off-state isolation, and charge injection alongside the 175 ohm maximum on-resistance. Request current availability and lead time through the Request a Quote form on this page before releasing a production order.

Comparison with Alternatives

Parameter This Product DG211DY+ DG211CSE+ DG211CJ+ DG211DY DG211DY-T1
Brand Analog Devices Analog Devices Analog Devices Analog Devices Vishay Intertechnology Vishay Intertechnology
Package 16-SOIC 16-SOIC - same 16-SOIC - same 16-SOIC - same 16-SOIC - same 16-SOIC - same

Key Differentiators

  • Four normally closed analog routes in one package (vs DG211CJ+)
  • Guaranteed break-before-make switching (vs DG211DY)
  • Robust behavior with powered-down signal inputs (vs DG211CSE+)

Design Notes

Treat the DG211DY+T as an analog impedance element rather than an ideal logic switch. The 175 ohm maximum on-resistance must be included in the source impedance and attenuation budget of the selected channel. For high-impedance sensors, evaluate leakage, off-state isolation, and charge injection because the 1000 ns turn-on specification does not describe the settling error seen by the analog node.

Route each switched signal directly to its associated source and drain pins and avoid long shared traces beneath the device. Keep control inputs away from sensitive analog nets, provide a low-impedance ground reference, and place bypass capacitance close to the supply pins. These measures reduce parasitic coupling and help preserve the manufacturer's glitch-free and break-before-make performance in practical board layouts.

Design the supply rails for the full ±4.5 V to ±18 V operating range, including startup and power-down states where external signals may remain connected. The manufacturer guarantees latch-up resistance under that condition, but good engineering still requires controlled sequencing and verification that every analog node stays within its permitted voltage. Confirm the control-input logic thresholds against the actual positive and negative supply voltages before releasing the board.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The component is a commercial analog switch rather than an AEC-Q100 automotive device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established by the available manufacturer and distributor records.

Data verified on: 2026-11-16 — data verified and curated by XAIPART's component engineering team

Related Searches

DG211DY+T datasheet DG211DY+T pinout DG211DY+T 16-SOIC DG211DY+T equivalent DG211DY+T replacement DG211DY+T cross reference DG211DY+T price DG211DY+T stock Analog Devices DG211DY+T DG211DY+T vs DG211CSE+ DG211DY+T vs DG211CJ+ DG211DY+T analog switch application circuit DG211DY+T 175 ohm on resistance

Related Components & Terms

Analog Devices Maxim Integrated DG211DY+T DG211DY+ DG211CSE+ DG211CJ+ DG211DY DG211DY-T1 Vishay Intertechnology analog switch SPST switch normally closed switch CMOS analog switch analog multiplexer demultiplexer break-before-make switching glitch-free switching on-resistance 175 ohm on-resistance ±4.5 V to ±18 V supply 16-SOIC package surface mount latch-up protection analog signal routing automated test equipment data acquisition precision instrumentation
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details