DG211DY+T - Quad SPST CMOS Analog Switch | Analog Devices
부품 번호: DG211DY+T ✓ 활성DG211DY+T 개요
An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The SPST designation means each of the four internal switches has one pole and one throw, while normally closed means each signal is connected to its throw terminal when the control input is inactive. The DG211 belongs to the broader analog-switch hierarchy, alongside multiplexers and demultiplexers, and provides a simple impedance-controlled routing function for test, measurement, and communication equipment.
Key electrical characteristics include a maximum on-resistance of 175 ohm, a maximum turn-on time of 1000 ns, and a maximum turn-off time of 500 ns. Maxim guarantees break-before-make operation, reducing the interval during which old and new signal paths can overlap. The device is also guaranteed not to latch up when its power supplies are disconnected while input signals remain connected, an important robustness characteristic for externally biased analog nodes.
The DG211 uses CMOS switch channels controlled by TTL-compatible control inputs. Its low-leakage design supports precision measurement systems where unintended charge transfer or off-state conduction can corrupt results. Operating from positive and negative rails allows direct connection to bipolar signals without translating every input through separate amplifiers, although common-mode voltage and supply limits must still be respected during layout and system design.
Typical uses include automated test equipment, data-acquisition systems, instrumentation, communication routing, and analog signal multiplexing. A four-channel normally closed switch is particularly useful where a measurement path must remain connected during idle periods and disconnect only when the control logic selects another operating condition.
PCB design should minimize capacitance on control and analog signal traces, keep routing short, and use a continuous ground reference beneath the device where practical. Because the switch is intended for analog signals rather than high-speed digital links, pay close attention to leakage, on-resistance, charge injection, and off-state isolation rather than digital edge-rate limits.
This page consolidates manufacturer specifications, supply-chain observations, drop-in alternatives, and practical design guidance that engineers would otherwise have to assemble from separate datasheets and component listings.
드롭인 대체품: DG211DY+T — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: DG211DY+T (동일 폼 팩터 및 풋프린트) — 차이점: Latch-Up Protection, Mounting Type, Package, Switch Configuration, Switching Behavior.
DG211DY+
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DG211CSE+
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DG211CJ+
✅ 드롭인가격 문의
데이터시트 보기 →DG211DY
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DG211DY-T1
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DG211DY+T 최대 정격 & 전기적 특성
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 SPST |
| Number of Switches | 4 normally closed SPST switches |
| On-Resistance | 175 ohm maximum |
| Technology | CMOS |
| Positive Supply Range | +4.5 V to +18 V |
| Negative Supply Range | -4.5 V to -18 V |
| Total Supply Range | ±4.5 V to ±18 V |
| Turn-On Time | 1000 ns maximum |
| Turn-Off Time | 500 ns maximum |
| Switching Behavior | Break-before-make guaranteed |
| Switching Transients | Glitch-free switching |
| Latch-Up Protection | Guaranteed not to latch up with disconnected supplies and connected input signals |
| 동작 온도 범위 | -40 °C to +85 °C |
| 패키지 | 16-SOIC, 0.154 inch (3.90 mm) width |
| 실장 유형 | Surface mount |
| Package Height | 1.75 mm maximum |
DG211DY+T 1.75 mm maximum 핀 구성 가이드
DG211DY+T(1.75 mm maximum 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: DG211DY+T.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
DG211DY+T 적합 용도: 6 애플리케이션s: Automated Test Equipment Signal Routing, Data Acquisition and Multiplexer Front Ends, Precision Instrumentation Signal Isolation, Analog Multiplexing in Communication Equipment, Power-Sequencing and Test-Path Control, Audio and Low-Frequency Analog Routing.
Automated Test Equipment Signal Routing
The DG211DY+T fits automated test systems that must connect and isolate several analog measurement channels while preserving a defined default connection. Its four normally closed SPST paths operate from ±4.5 V to ±18 V, and the guaranteed break-before-make behavior prevents an instantaneous overlap between old and new routes. With a maximum on-resistance of 175 ohm and turn-off time of 500 ns, the device is appropriate for general-purpose, low-to-moderate-frequency instrumentation rather than high-bandwidth signal chains. Design the fixture interface around the control polarity and verify leakage and charge injection when the measured node has high source impedance.
추천
Data Acquisition and Multiplexer Front Ends
The DG211DY+T can connect multiple analog inputs to a shared measurement chain in data-acquisition equipment. Four normally closed channels reduce the component count compared with four separate single switches, while the 16-SOIC footprint keeps routing manageable on a dense measurement board. The 1000 ns maximum turn-on time is short compared with many measurement settling intervals, but switch on-resistance, leakage, off-state isolation, and injected charge can dominate accuracy at high input impedance. Use the device for moderate-bandwidth analog multiplexing and follow the manufacturer pin configuration when arranging source, drain, control, and supply nets.
추천
Precision Instrumentation Signal Isolation
The DG211DY+T is useful in instrumentation that needs a normally connected path during idle conditions and deliberate disconnection for calibration or fault isolation. Its CMOS channels operate across ±4.5 V to ±18 V rails, and the manufacturer guarantees latch-up resistance when supplies are removed while input signals remain present. That behavior improves robustness in systems where external test fixtures can drive an input after the board is unpowered. For high-accuracy measurements, evaluate leakage and off-state isolation in addition to the 175 ohm maximum on-resistance, and keep the analog routing away from high-speed switching nodes.
추천
Analog Multiplexing in Communication Equipment
The DG211DY+T can implement four independent analog routes in communication and interface equipment where a compact, low-frequency multiplexer is sufficient. The normally closed configuration keeps each path connected until its control input changes state, and the specified 1000 ns turn-on and 500 ns turn-off times support straightforward control sequencing. The ±4.5 V to ±18 V supply capability suits both positive-only and split-rail implementations. Designers should preserve the guaranteed break-before-make behavior, control trace impedance, and supply sequencing, especially when the routed signals exceed the logic levels used to control the switch.
추천
Power-Sequencing and Test-Path Control
The DG211DY+T can disconnect a powered subsystem from a common test node while leaving other channels in their default state. Its latch-up guarantee provides useful protection when supplies are removed before the routed signal, and the guaranteed break-before-make transition avoids an uncontrolled interval in which two paths could overlap. This makes the switch useful in power-sequencing and isolation test boards. Validate the exact logic levels, supply ramps, and maximum analog-node voltage in the manufacturer data sheet, and use the Request a Quote form on this page to confirm availability for production builds.
추천
Audio and Low-Frequency Analog Routing
The DG211DY+T can route four low-frequency analog signals in audio equipment, control panels, or mixed-signal modules where a normally closed default connection is preferred. The 175 ohm maximum on-resistance is acceptable for many low-impedance audio paths, while glitch-free operation helps reduce visible switching disturbances under valid operating conditions. A dual supply from ±4.5 V to ±18 V allows the switch to handle bipolar control or monitor signals directly. Because the part is not specified as a high-speed audio multiplexer, verify channel bandwidth, off-state isolation, and charge injection against the source impedance and signal quality requirements.
추천
추천 제품 요약
엔지니어링 참조 데이터: DG211DY+T — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | DG211DY+ | DG211CSE+ | DG211CJ+ | DG211DY | DG211DY-T1 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Vishay Intertechnology | Vishay Intertechnology |
| Package | 16-SOIC | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same | 16-SOIC - same |
주요 차별점
- Four normally closed analog routes in one package (vs DG211CJ+)
- Guaranteed break-before-make switching (vs DG211DY)
- Robust behavior with powered-down signal inputs (vs DG211CSE+)
설계 노트
Treat the DG211DY+T as an analog impedance element rather than an ideal logic switch. The 175 ohm maximum on-resistance must be included in the source impedance and attenuation budget of the selected channel. For high-impedance sensors, evaluate leakage, off-state isolation, and charge injection because the 1000 ns turn-on specification does not describe the settling error seen by the analog node.
Route each switched signal directly to its associated source and drain pins and avoid long shared traces beneath the device. Keep control inputs away from sensitive analog nets, provide a low-impedance ground reference, and place bypass capacitance close to the supply pins. These measures reduce parasitic coupling and help preserve the manufacturer's glitch-free and break-before-make performance in practical board layouts.
Design the supply rails for the full ±4.5 V to ±18 V operating range, including startup and power-down states where external signals may remain connected. The manufacturer guarantees latch-up resistance under that condition, but good engineering still requires controlled sequencing and verification that every analog node stays within its permitted voltage. Confirm the control-input logic thresholds against the actual positive and negative supply voltages before releasing the board.
규정 준수 정보
The component is a commercial analog switch rather than an AEC-Q100 automotive device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established by the available manufacturer and distributor records.