Texas Instruments

DP83846AVHG/NOPB - 10/100 Ethernet PHY | Texas Instruments

MPN: DP83846AVHG/NOPB ✓ Active
3 V to 3.6 V Vdss 80-LQFP, 12 x 12 mm Package
MOQ: 1 |

DP83846AVHG/NOPB Overview

The Texas Instruments DP83846AVHG/NOPB is a single 10/100 Ethernet physical-layer transceiver with integrated PMD sublayers, supplied in an 80-pin LQFP package measuring 12 x 12 mm. It supports 10BASE-T and 100BASE-TX operation over Category 3 or Category 5 unshielded twisted-pair cables while operating from a 3 V to 3.6 V supply.

An Ethernet physical-layer device, commonly called an Ethernet PHY, converts digital data into signals suitable for twisted-pair cabling and converts received signals back into digital data. In the system hierarchy, a PHY is an interface IC within Ethernet connectivity and network-interface hardware. The DP83846A family provides one Ethernet transceiver channel for equipment requiring 10 Mb/s or 100 Mb/s links rather than gigabit Ethernet.

Key features include support for both 10BASE-T and 100BASE-TX protocols, integrated PMD sublayers, a 3 V to 3.6 V operating supply range, and an 80-LQFP package. The commercial-temperature grade and surface-mount construction suit industrial, networking, embedded-control, and communications equipment. Tray packaging is identified for DP83846AVHG/NOPB, allowing the component to be assembled using standard PCB manufacturing processes.

The device integrates the physical communication functions required for copper-pair Ethernet connectivity. Its single-channel architecture is appropriate for one 10/100 network link on a controller, test instrument, access terminal, or embedded network appliance. The 100BASE-TX mode supports Category 5 cable installations, while 10BASE-T can use Category 3 or Category 5 unshielded twisted pair. Network design must still provide suitable magnetic-component or magnetics-interface support and appropriate PCB signal integrity.

Typical uses include industrial Ethernet controllers, embedded Linux systems, network interface cards, communications equipment, and legacy or cost-sensitive 100 Mb/s installations. DP83846AVHG/NOPB is particularly relevant when a product requires a dedicated single-port 10/100 PHY rather than a multi-port switching solution. The device is also appropriate for equipment designed around Category 3 or Category 5 copper cabling and a 3.3 V power architecture.

PCB implementation should preserve the differential characteristic and controlled impedance of each twisted-pair channel. Place the PHY close to its connector and magnetics interface, maintain the manufacturer-recommended support-network layout, and provide solid return paths for the digital supply. Careful isolation between Ethernet magnetics and noisy digital circuitry helps reduce radiated emissions and susceptibility to external interference.

This product page combines the confirmed device identity, package information, operating limits, functional standards, drop-in comparison, and application-specific engineering guidance. It also organizes the principal selection considerations for engineers evaluating the DP83846A family in single-port 10/100 Ethernet designs.

Drop-in alternatives for DP83846AVHG/NOPB — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with DP83846AVHG/NOPB (same form factor and footprint) — differing in Package, Product Type, Terminal Form.

Texas Instruments
Package: 80-pin LQFP, 12 x 12 mm
Texas Instruments
Package: 80-LQFP (12 mm x 12 mm)
Product Type: Single 10/100 Ethernet Transceiver
Terminal Form: Gull wing

DP83846AVHG

✅ Drop-In
Texas Instruments
📦 80-LQFP (12 x 12 mm)
Single 10/100 Ethernet physical-layer transceiver · 10 Mb/s and 100 Mb/s · Supported · Supported · 10 Mb/s operation · Supported for 100BASE-TX operation · Integrated · 1 port

Contact for price

View Datasheet →

DP83846AVHG/NOPB Specifications

Product Type Single 10/100 Ethernet physical-layer transceiver
Ethernet Channel Count 1 channel
Supported Data Rates 10 Mb/s and 100 Mb/s
Supported Protocols 10BASE-T and 100BASE-TX
Integrated Functions Integrated PMD sublayers
Supply Voltage Range 3 V to 3.6 V
Cable Category Support Category 3 and Category 5 unshielded twisted-pair cable
Package 80-LQFP, 12 x 12 mm
Pin Count 80 pins
Terminal Form Gull-wing
Package Shape Square
Temperature Grade Commercial
Packaging Tray
Mounting Type Surface mount

DP83846AVHG/NOPB square Pin Configuration Guide

Pin configuration for DP83846AVHG/NOPB (square package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

square package pinout diagram for DP83846AVHG/NOPB

No detailed pinout data available for DP83846AVHG/NOPB.

Refer to the datasheet for full pin configuration.

Typical Applications

DP83846AVHG/NOPB is suitable for 6 applications: Industrial Ethernet Controller Interface, Embedded Network Appliance, Network Interface Card, Communications Terminal, Test and Measurement Instrument, Legacy 100 Mb/s Equipment.

🏭

Industrial Ethernet Controller Interface

The DP83846AVHG/NOPB fits a single-port industrial Ethernet design requiring either 10BASE-T or 100BASE-TX connectivity. Its one-channel PHY supports 10 Mb/s and 100 Mb/s operation from a 3 V to 3.6 V supply, while the integrated PMD sublayers reduce the physical-layer circuitry required around the host controller. In an industrial controller, the device can sit between the network processor and compliant magnetics, providing a standardized copper-facing PHY for Category 3 or Category 5 unshielded twisted-pair cabling. The design should preserve the manufacturer-recommended support network, controlled differential impedance, and a quiet return path. Because this is a single 10/100 port rather than a multi-port switch, it is most appropriate when throughput and port count do not justify a more integrated Ethernet solution.

🧩

Embedded Network Appliance

DP83846AVHG/NOPB is appropriate for an embedded Linux or microcontroller appliance that needs one wired network port at 10 or 100 Mb/s. The device's supported 10BASE-T and 100BASE-TX modes offer compatibility with installed Category 3 and Category 5 cabling, avoiding a requirement for new media infrastructure. With a 3 V to 3.6 V operating range, the PHY can operate from a conventional 3.3 V rail, although its network-facing analog circuitry still needs clean supply and carefully controlled layout. Designers should place the PHY near the connector and magnetics, route each differential pair as a controlled-impedance pair, and follow the Texas Instruments reference layout. This arrangement supports predictable Ethernet link behavior while keeping the appliance architecture simple and cost-conscious.

🌐

Network Interface Card

The DP83846AVHG/NOPB can serve as the copper Ethernet PHY on a single-port network interface card intended for Fast Ethernet rather than gigabit networking. Its 10BASE-T and 100BASE-TX support permits automatic operation across 10 Mb/s and 100 Mb/s links when the host interface and system configuration support both rates. The 80-LQFP surface-mount package is practical for multilayer PCB assembly, and the 3 V to 3.6 V supply range aligns with common 3.3 V interface ecosystems. To obtain reliable operation, the board must provide the required magnetics interface, differential-pair routing, clocking, reset, and supply decoupling specified by Texas Instruments. The single-channel architecture also provides a straightforward option for legacy or cost-focused adapter designs.

📡

Communications Terminal

DP83846AVHG/NOPB is suitable for a communications terminal that needs one standardized copper Ethernet connection for configuration, management, or data transfer. Supporting both 10BASE-T and 100BASE-TX allows the terminal to connect to 10 Mb/s or 100 Mb/s network infrastructure using Category 3 or Category 5 unshielded twisted-pair cable. The PHY's integrated PMD sublayers handle the physical medium interface, while the host processor manages framing and higher-level protocols. Implement the circuit with the Texas Instruments recommended support components and keep the Ethernet differential pairs away from noisy switching nodes. Because the device has one Ethernet channel, a multiport terminal would require additional PHY circuitry or a switching solution instead of duplicating pins on this package.

🖥️

Test and Measurement Instrument

The DP83846AVHG/NOPB can provide a 10/100 Ethernet control or synchronization link in a test and measurement instrument. Many instrument-control networks operate comfortably at 10 or 100 Mb/s, so the PHY's 10BASE-T and 100BASE-TX support aligns with those applications. A 3.3 V system architecture can use the device's 3 V to 3.6 V operating range, provided local decoupling and analog grounding follow the reference design. For reliable measurements, keep the copper interface physically separated from sensitive analog sections and maintain controlled impedance on both Ethernet pairs. The single-channel configuration is suitable for one management port; instruments requiring several isolated network connections should allocate additional Ethernet PHYs rather than multiplexing unrelated circuitry through this package.

🔧

Legacy 100 Mb/s Equipment

DP83846AVHG/NOPB is well suited to legacy or cost-sensitive equipment that must interoperate with 100 Mb/s Fast Ethernet infrastructure. The device supports both 10BASE-T and 100BASE-TX, so it can operate within networks containing older 10 Mb/s endpoints as well as faster 100 Mb/s links. Category 3 compatibility is useful for 10BASE-T installations, while Category 5 twisted pair supports 100BASE-TX. The PHY occupies an 80-LQFP surface-mount package and operates from 3 V to 3.6 V, enabling integration into established 3.3 V boards. When upgrading an existing design, verify the host-controller bus timing, clock source, reset arrangement, magnetics selection, and every pin assignment against the Texas Instruments manufacturer datasheet.

What is the DP83846AVHG/NOPB?
The DP83846AVHG/NOPB is a single-channel 10/100 Ethernet physical-layer transceiver from Texas Instruments. According to the Texas Instruments manufacturer datasheet, it supports 10BASE-T and 100BASE-TX communication with integrated PMD sublayers. The device is intended for one copper Ethernet connection operating at either 10 Mb/s or 100 Mb/s and is housed in an 80-LQFP package measuring 12 x 12 mm.
What Ethernet data rates does DP83846AVHG/NOPB support?
The DP83846AVHG/NOPB supports 10 Mb/s and 100 Mb/s Ethernet operation. The Texas Instruments manufacturer datasheet identifies the device as a single 10/100 Ethernet transceiver supporting the 10BASE-T and 100BASE-TX protocols. This makes the part suitable for legacy Fast Ethernet equipment, embedded network controllers, and copper links that do not require the 1 Gb/s throughput of a gigabit PHY.
What supply voltage does DP83846AVHG/NOPB require?
The DP83846AVHG/NOPB operates from a 3 V to 3.6 V supply. This 3.3 V-compatible operating range is stated in the Texas Instruments component information and is appropriate for systems whose digital and analog rails are generated around 3.3 V. A well-decoupled supply is essential because Ethernet signal integrity, clocking, and biasing performance depend on a stable low-noise source near the device.
What package does DP83846AVHG/NOPB use?
The DP83846AVHG/NOPB uses an 80-LQFP package measuring 12 x 12 mm. The Texas Instruments manufacturer datasheet and component listings identify gull-wing terminals, a square package, and an 80-pin configuration. DP83846AVHG/NOPB is supplied in a tray. Use the package drawing and pin-description table in the manufacturer datasheet when creating the land pattern and assigning PCB nets.
What cable types can DP83846AVHG/NOPB use?
The DP83846AVHG/NOPB supports Category 3 and Category 5 unshielded twisted-pair cable for 10BASE-T and 100BASE-TX links. The Texas Instruments manufacturer datasheet identifies both cable categories as supported media. The exact installation still requires compliant magnetics or a suitable network-interface isolation arrangement, correct pair routing, and controlled-impedance PCB construction between the PHY and the cable interface.
Where can I download the DP83846AVHG/NOPB datasheet PDF?
The DP83846AVHG/NOPB datasheet PDF is available from the official Texas Instruments product documentation for DP83846A. The manufacturer document describes the 10BASE-T and 100BASE-TX physical layer, electrical characteristics, pin descriptions, and application implementation. Use the manufacturer's pin-description table and recommended layout diagrams when assigning terminals or reproducing the reference circuit.
Where is the DP83846AVHG/NOPB pinout?
The DP83846AVHG/NOPB pinout is located in the pin-description table of the Texas Instruments DP83846A manufacturer datasheet. The device uses an 80-LQFP package with 80 terminals, so the complete schematic assignment must be checked against all numbered pins and the package drawing. Do not infer the pinout from another Ethernet PHY because functions, strap pins, and package assignments can differ.
Is DP83846AVHG a drop-in replacement for DP83846AVHG/NOPB?
The DP83846AVHG is identified as a fully replaceable counterpart for DP83846AVHG/NOPB, with consistent terminals, package, and principal performance characteristics. Both are listed as one-channel 10/100 Ethernet transceivers in 80-LQFP packages, so the stated device-to-device difference is 0 Mb/s in supported data rate and 0 V in stated supply range. Confirm the exact ordering suffix and assembly requirements before approving a substitution.
What is the best drop-in replacement for DP83846AVHG/NOPB?
The DP83846AVHG is the closest documented drop-in replacement because it retains the same one-channel 10/100 Ethernet function, 80-LQFP package, and stated principal electrical characteristics. The documented package difference is 0 pins and 0 mm of body-size difference. Review ordering-code, packaging, and qualification requirements before using it in a new production release because suffix details can control lead finish or delivery format.
What can replace DP83846AVHG/NOPB?
The documented replacement for DP83846AVHG/NOPB is the DP83846AVHG, which uses the same 80-LQFP footprint and 10BASE-T/100BASE-TX functionality. The published comparison describes the terminal assignments and package as consistent, eliminating a PCB change. No same-package cross-brand replacement with sufficient verified pin and parameter detail was established, so board changes should not be assumed for other Ethernet PHY products.
Is DP83846AVHG/NOPB the same as DP83846AVHG?
The DP83846AVHG/NOPB and DP83846AVHG are functionally equivalent 10/100 Ethernet transceivers with the same 80-LQFP package and consistent terminal arrangement. Their documented data-rate difference is 0 Mb/s, and their stated supply-voltage difference is 0 V. The remaining distinction lies in the ordering suffix, so procurement and production engineers should confirm the exact suffix, packaging, and manufacturing requirements before treating them as identical.
When should I choose DP83846AVHG/NOPB over DP83846AVHG?
Choose DP83846AVHG/NOPB when the specified ordering code, tray format, and manufacturer qualification flow match the product design. Choose DP83846AVHG when it is the approved ordering option and its suffix-specific commercial conditions are acceptable. The two devices support the same 1-channel 10 Mb/s and 100 Mb/s operation in the same 80-LQFP footprint, so functional performance does not distinguish the options.
Is DP83846AVHG/NOPB suitable for a 100 Mb/s embedded Ethernet port?
The DP83846AVHG/NOPB is suitable for a single 100 Mb/s embedded Ethernet port because it supports 100BASE-TX and 10BASE-T with integrated PMD sublayers. Its 3 V to 3.6 V supply range fits a 3.3 V system, and its 80-LQFP package supports conventional surface-mount assembly. The host controller interface, clock source, reset behavior, and magnetics connection must still be matched to the system requirements.
Where can I buy DP83846AVHG/NOPB and check its lead time?
Use the Request a Quote form on this page to ask about DP83846AVHG/NOPB availability, current lead time, minimum order quantity, and tray quantities. The product is currently presented as an orderable Texas Instruments Ethernet transceiver, but a confirmed manufacturing allocation and delivery schedule should be obtained through the quote process. The 80-LQFP package is supplied in a tray according to the component information.
How should DP83846AVHG/NOPB be used in a 10BASE-T design?
In a 10BASE-T design, DP83846AVHG/NOPB operates in its 10 Mb/s mode over Category 3 or Category 5 unshielded twisted-pair cable. The host controller communicates with the PHY while the PHY interfaces to the copper network through suitable magnetics or isolation circuitry. Use the Texas Instruments reference layout to preserve pair symmetry, controlled impedance, grounding, and supply-decoupling requirements.
How should DP83846AVHG/NOPB be used in a 100BASE-TX design?
For a 100BASE-TX port, DP83846AVHG/NOPB operates at 100 Mb/s over Category 5 unshielded twisted-pair cable. Its integrated PMD sublayers perform the physical-layer functions, while the system supplies the controller interface, clocking, reset, and magnetics interface. Follow the Texas Instruments layout guidance to minimize differential-pair imbalance, return-path discontinuities, and radiated emissions.

Engineering reference data for DP83846AVHG/NOPB — comparison, design guidance, and compliance information.

Selection Guide

Choose DP83846AVHG/NOPB for a new single-port 10/100 Ethernet design that uses a 3.3 V supply and Category 3 or Category 5 copper cabling. Select DP83846AVHG when that ordering suffix is approved by procurement and manufacturing; it is the documented drop-in option with the same 80-LQFP footprint, terminal arrangement, and principal 10BASE-T/100BASE-TX characteristics. Use a gigabit PHY such as KSZ9131RNXC or KSZ9893RNXC when the application requires 1 Gb/s links or needs headroom for future traffic growth. Use a multi-port device such as KSZ9021GN-TR when several Ethernet interfaces are required. The DP83846A family is not the correct choice for a copper interface requiring Auto-MDIX, multi-pair operation, or another media type unless the complete host interface and magnetics design are explicitly adapted.

Comparison with Alternatives

Parameter This Product DP83846AVHG
Package 80-LQFP (12 x 12 mm) 80-LQFP (12 x 12 mm)
Brand Texas Instruments Texas Instruments
Ethernet Channel Count 1 channel 1 channel
Supported Data Rates 10 Mb/s and 100 Mb/s 10 Mb/s and 100 Mb/s
Supported Protocols 10BASE-T and 100BASE-TX 10BASE-T and 100BASE-TX
Integrated PMD Sublayers Yes Yes

Key Differentiators

  • Exact functional and package compatibility (vs DP83846AVHG)
  • Single 10/100 copper-channel architecture (vs KSZ9131RNXC)
  • Compatibility with legacy and current Fast Ethernet cabling (vs KSZ9893RNXC)

Design Notes

Use the Texas Instruments recommended layout as the controlling reference for the 80-LQFP land pattern, support network, and Ethernet routing. Place the PHY close to the connector and magnetics interface, route the two pairs as controlled-impedance differential connections, and avoid introducing stubs or layer transitions across the high-speed portions of each pair. Keep the connector, magnetics, and PHY in a consistent signal-flow arrangement so common-mode energy is referenced predictably.

Implement the input and bypass network specified in the manufacturer reference design, including the required capacitance, voltage rating, and placement directly beside the relevant supply terminals. A stable 3.3 V source is necessary for correct biasing and signal generation, but local high-frequency decoupling remains important because supply impedance between the source and the PHY can affect noise and edge behavior.

Separate Ethernet differential pairs from clocks, switching nodes, magnetic components, and other high-energy circuits. Keep copper return paths continuous beneath the pairs where the reference layout calls for them, and match the two members of each differential pair for length and symmetry. Avoid routing copper or test-probe structures beneath sensitive network nodes when doing so changes isolation or coupling.

Do not assume that every Ethernet PHY with a similar body size is a drop-in replacement. The DP83846AVHG is the documented compatible option because its terminals and 80-LQFP package are consistent with the target. Before reuse, confirm the host-interface voltage and timing, clock source, reset polarity, strap configuration, magnetics selection, and all 80 terminal assignments in the Texas Instruments manufacturer datasheet.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The confirmed component information identifies the part as a commercial-grade Ethernet transceiver in an 80-LQFP tray package. Specific RoHS, REACH, automotive, lead-free, halogen-free, and conflict-minerals declarations were not stated and must be confirmed for the exact ordering code.

Related Searches

DP83846AVHG/NOPB datasheet DP83846AVHG/NOPB pinout DP83846AVHG/NOPB datasheet pdf DP83846AVHG/NOPB equivalent DP83846AVHG/NOPB replacement DP83846AVHG/NOPB schematic DP83846AVHG/NOPB footprint DP83846AVHG/NOPB price DP83846AVHG/NOPB stock Texas Instruments DP83846AVHG/NOPB DP83846A 10/100 Ethernet PHY 80-LQFP 10/100 Ethernet transceiver DP83846AVHG vs DP83846AVHG/NOPB DP83846AVHG Category 5 application circuit DP83846AVHG/NOPB 3V 3.6V

Related Components & Terms

Texas Instruments DP83846AVHG/NOPB DP83846AVHG DP83846A Ethernet PHY physical-layer transceiver single 10/100 Ethernet 10BASE-T 100BASE-TX PMD sublayers Fast Ethernet Category 3 cable Category 5 cable unshielded twisted pair 3 V to 3.6 V supply 80-LQFP LQFP package gull-wing terminals surface mount industrial Ethernet embedded Ethernet network interface card differential pair controlled impedance
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details