Texas Instruments

DS90CR285SLC - 28-Bit 66MHz LVDS Transmitter | TI

MPN: DS90CR285SLC ✗ End of Life
3 V to 3.6 V Vdss 64-NFBGA (8 x 8 mm) Package 66 MHz Speed
MOQ: 1 |

DS90CR285SLC Overview

Texas Instruments DS90CR285SLC is a 28-bit rising-edge data-strobe LVDS transmitter rated for 66 MHz and packaged in a 64-NFBGA (8 x 8 mm) package. It operates from a 3 V to 3.6 V supply and converts 28 bits of LVCMOS or LVTTL data into four differential LVDS outputs, with one clock channel providing a 66 MHz data-strobe interface.

A low-voltage differential signaling transmitter is an interface IC that transfers high-speed data between circuit boards or between devices over differential pairs. LVDS belongs to the broader interface-IC hierarchy, where low-voltage, low-power differential signaling is used for clock distribution, video, graphics, communications, and industrial control systems. Compared with single-ended parallel signaling, LVDS provides common-mode noise rejection and enables reliable transmission through controlled-impedance interconnects.

The DS90CR285 provides a 28-bit parallel input and serializes that data across four LVDS data outputs at up to 66 MHz. The 3 V to 3.6 V operating range supports conventional 3.3 V digital systems. The 64-NFBGA package provides a compact surface-mount footprint, while its many connections support separate data channels, differential pairs, power, ground, and control functions.

The transmitter is designed for parallel-to-LVDS conversion where a source device must communicate with an LVDS receiver over a balanced cable, backplane, or controlled-impedance PCB channel. Its rising-edge data-strobe architecture carries a forwarded clock alongside data, allowing the receiving system to establish a deterministic sampling relationship. Systems using this device must account for signal-pair geometry, termination, trace impedance, connector loss, and skew between the clock and data channels.

Typical uses include industrial control systems, data-acquisition equipment, display and graphics interfaces, telecommunications equipment, and embedded systems that connect a CMOS parallel bus to an LVDS link. The 66 MHz operating rate and four differential outputs make the device especially relevant to multi-lane transfers requiring more aggregate bandwidth than a single LVDS pair can provide.

For layout, route each differential pair as a tightly coupled, length-matched pair over a continuous reference plane. Place receiver-side termination close to the endpoint and verify AC coupling, biasing, and clock/data alignment in the complete channel. Because the package has 64 balls, inspect the manufacturer pin-description table before assigning power, ground, data, clock, and no-connect positions to the PCB.

This page combines the device’s documented interface characteristics, practical PCB implementation guidance, sourcing questions, and an explicit assessment of drop-in replacement evidence. It also highlights the distinction between a mechanically similar serializer and a genuinely pin-compatible substitute, helping engineers avoid replacement assumptions that could compromise signal integrity or system functionality.

Drop-in alternatives for DS90CR285SLC — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

No drop-in alternatives available for this product.

Request Alternatives

DS90CR285SLC Specifications

Product Type 28-bit LVDS transmitter
Supply Voltage Range 3 V to 3.6 V
Nominal Supply Voltage 3.3 V
Clock Frequency 66 MHz
Input Data Width 28 bits
Input Logic LVCMOS/LVTTL
Output Logic LVDS
Number of LVDS Data Outputs 4 differential outputs
Data Transfer Architecture Rising-edge data strobe
Package 64-NFBGA (8 x 8 mm)
Pin Count 64 balls
Mounting Type Surface mount
Packaging Tube
Lead-Free Status Contains lead
RoHS Status RoHS non-compliant

DS90CR285SLC 64-nfbga (8 x 8 mm) Pin Configuration Guide

Pin configuration for DS90CR285SLC (64-nfbga (8 x 8 mm) package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

64-nfbga (8 x 8 mm) package pinout diagram for DS90CR285SLC

No detailed pinout data available for DS90CR285SLC.

Refer to the datasheet for full pin configuration.

Typical Applications

DS90CR285SLC is suitable for 6 applications: Industrial Control Data Links, Data-Acquisition Equipment, Display and Graphics Interfaces, Telecommunications Equipment, Embedded Processor Data Transport, Test and Measurement Systems.

🏭

Industrial Control Data Links

The DS90CR285SLC is appropriate for transferring a 28-bit parallel control or data word from a controller to a remote receiver over four differential LVDS lanes. Its 3 V to 3.6 V operating range matches conventional 3.3 V industrial logic, while the 66 MHz clock rate provides a deterministic sampling reference for command, status, or supervisory data. The four LVDS pairs reduce the number of high-speed interconnects compared with sending 28 bits as single-ended signals. Layout should use tightly coupled differential routing, a continuous reference plane, and receiver-side termination selected for the complete cable and receiver configuration.

📊

Data-Acquisition Equipment

The DS90CR285SLC can serialize a 28-bit acquisition or processing bus into four LVDS data channels clocked at up to 66 MHz. This arrangement is useful when the source logic is parallel but the remote instrument, test system, or processing board requires a balanced cable connection. The rising-edge data-strobe architecture provides a forwarded clock so the receiver can capture data at a defined point in the transmission cycle. Channel skew, connector loss, AC-coupling requirements, and termination must be evaluated together because a compliant transmitter does not guarantee adequate margin in every physical link.

📺

Display and Graphics Interfaces

The DS90CR285SLC can serve as the parallel-to-LVDS stage between a display or graphics source and a downstream receiver. Its 28-bit input width and four differential outputs support a compact high-speed channel, while the 66 MHz clock limit defines the maximum supported transfer rate. For video-like traffic, maintain uniform impedance through connectors and cable transitions, minimize pair-length mismatch, and observe the receiver’s clock-to-data tolerance. The compact 64-NFBGA footprint also helps preserve board area, although careful escape routing and uninterrupted return paths remain necessary around all 64 balls.

🌐

Telecommunications Equipment

The DS90CR285SLC is suitable for parallel-to-LVDS conversion inside telecommunications equipment requiring a balanced backplane or cable interface. Four differential lanes operating with a 66 MHz clock can carry a 28-bit payload while reducing connector pin count relative to a wide parallel bus. Designers should use manufacturer-recommended differential impedance, provide a continuous ground reference, and confirm receiver termination and clock/data alignment across the full operating channel. Because this device is a legacy interface IC, production designs should also confirm lifecycle, longevity, and assembly availability through a formal sourcing review.

🖥️

Embedded Processor Data Transport

The DS90CR285SLC can connect a 28-bit parallel subsystem to an LVDS-enabled peripheral, remote processor, or backplane endpoint. The device accepts conventional 3.3 V LVCMOS or LVTTL logic and converts it into four low-voltage differential outputs at up to 66 MHz. This arrangement is useful when an older parallel architecture must communicate over a shorter, balanced high-speed link without redesigning the source bus. The engineering task includes validating signal timing at the source, ensuring adequate clock-data margin, and selecting a receiver whose termination and input thresholds match the transmitted signal.

🔧

Test and Measurement Systems

The DS90CR285SLC can convert a 28-bit parallel source word into four differential LVDS lanes for remote instrumentation or automated test equipment. A forwarded clock supports repeatable sampling at the receiving endpoint, while the 3 V to 3.6 V supply range integrates naturally with 3.3 V test hardware. In bench and production systems, cable length, connector transitions, and receiver termination can materially affect the usable channel margin. Validate the complete transmitter-board, cable-or-backplane, and receiver combination at the intended 66 MHz maximum clock rather than relying only on source-device timing.

What is the DS90CR285SLC?
The DS90CR285SLC is a 28-bit rising-edge data-strobe LVDS transmitter that operates from 3 V to 3.6 V and supports clock frequencies up to 66 MHz. According to the Texas Instruments product page, the device converts 28 parallel LVCMOS or LVTTL data bits into four differential LVDS data outputs, with an accompanying clock channel. It is intended for high-speed point-to-point links using controlled-impedance PCB traces, cables, or backplanes.
What is the operating voltage of DS90CR285SLC?
The DS90CR285SLC operates from 3 V to 3.6 V and is identified as a +3.3 V device. This supply range places it in the conventional 3.3 V digital-interface class, allowing its LVCMOS or LVTTL inputs and LVDS outputs to operate from a 3.3 V system rail. Confirm individual power and ground pin assignments in the manufacturer pin-description table before finalizing the PCB schematic.
How many data bits and LVDS outputs does DS90CR285SLC support?
The DS90CR285SLC accepts 28 parallel data bits and serializes them onto four differential LVDS data outputs. It also supports a forwarded clock and uses a rising-edge data-strobe architecture. According to the Texas Instruments product description, this arrangement supports transfers at up to 66 MHz while reducing the number of high-speed signal pairs required compared with an unserialized parallel link.
What clock frequency does DS90CR285SLC support?
The DS90CR285SLC supports a maximum clock frequency of 66 MHz. According to the Texas Instruments product page, it is a 66 MHz rising-edge data-strobe LVDS transmitter. The parallel input data is converted into four differential LVDS outputs, creating a multi-lane interface suitable for communications, industrial control, display, data-acquisition, and other embedded systems requiring reliable transfer across a balanced channel.
Where can I download the DS90CR285SLC datasheet PDF?
The official DS90CR285 datasheet and product documentation are available through the Texas Instruments product page at https://www.ti.com/product/DS90CR285. Open the product page and select its datasheet or documentation resources. Use the manufacturer pin-description table to confirm all 64 ball assignments, differential output names, supply connections, and no-connect positions before laying out the board.
Where can I find the DS90CR285SLC pinout?
The DS90CR285SLC pinout must be taken from the pin-description table in the Texas Instruments DS90CR285 manufacturer datasheet. The device is a 64-NFBGA package with an 8 x 8 mm body, so a complete 64-ball map is required for PCB design. The searchable product page at https://www.ti.com/product/DS90CR285 provides access to the official documentation and supporting design information.
Is DS90CR285SLC a transmitter or receiver?
The DS90CR285SLC is a transmitter that converts 28 parallel LVCMOS or LVTTL data bits into four differential LVDS data outputs. It also forwards a clock through the rising-edge data-strobe interface. The DS90CR285 family description identifies the device as a 66 MHz transmitter, so it belongs on the sending side of an LVDS link rather than serving as the receiving endpoint.
Can DS90CR285SLC replace DS90CR286?
The DS90CR285SLC cannot automatically be treated as a drop-in replacement for a DS90CR286 receiver because one device is an LVDS transmitter and the other is a complementary receiver function. A transmitter-to-receiver substitution also changes the direction and signal architecture of the link. Use the manufacturer documentation to establish whether a receiver can tolerate the transmitter output and whether every required pin, voltage, and signal function is compatible.
What is the best drop-in replacement for DS90CR285SLC?
No confirmed drop-in replacement for the DS90CR285SLC was established from the available cross-reference results. A valid substitute must match the 64-NFBGA footprint, 3 V to 3.6 V supply range, 28-bit parallel input, four-pair LVDS output, 66 MHz clock rate, pin functions, and electrical timing. Generic cross-reference tools and listings that only describe similar devices are insufficient proof of pin-to-pin compatibility.
What can replace DS90CR285SLC?
The only defensible replacement is a device that is explicitly documented as pin-to-pin compatible with the DS90CR285SLC and matches its 28-bit parallel-to-four-pair LVDS conversion at up to 66 MHz. No qualifying substitute appears in the available cross-reference results. Before changing the design, compare the complete pin list, supply pins, LVDS output timing, input thresholds, package-ball map, and recommended termination.
When should I choose DS90CR285SLC over another LVDS transmitter?
Choose the DS90CR285SLC when the design requires a 28-bit parallel input, four differential LVDS data outputs, a forwarded clock, a 3 V to 3.6 V supply, and operation up to 66 MHz. Its 64-NFBGA package suits compact multichannel interfaces. A different transmitter should be selected only if its logic levels, serialization ratio, output count, clock range, pinout, and termination requirements better match the complete channel.
Is DS90CR285SLC suitable for industrial and display data links?
The DS90CR285SLC is suitable for systems requiring a compact four-pair LVDS link at up to 66 MHz, including industrial control, data-acquisition, display, graphics, and telecommunications equipment. Its suitability depends on implementing every differential pair over a continuous reference plane, observing length and skew limits, and using the termination method specified for the complete receiver and cable configuration.
What are the key specifications of DS90CR285SLC that engineers should know?
The principal DS90CR285SLC specifications are a 3 V to 3.6 V supply, a 28-bit LVCMOS or LVTTL input, four differential LVDS data outputs, a 66 MHz maximum clock, and a 64-NFBGA 8 x 8 mm package. It uses a rising-edge data-strobe interface and converts parallel data to a balanced mult-lane link. The 64-ball footprint requires careful high-speed layout and complete pin assignment verification.
Where can I buy DS90CR285SLC online?
Use the Request a Quote form on this page to request DS90CR285SLC availability, current pricing, and lot-level sourcing information. Because this is a specialized and potentially legacy interface component, the form allows buyers to request the exact MPN, quantity, date code, and packaging requirements. Current lead time and stock should be confirmed through the quotation response rather than assumed from a general search result.
What is the lead time and stock status for DS90CR285SLC?
Current stock and lead time for DS90CR285SLC should be requested through the Request a Quote form on this page. The specialized distributor listing indicates that this legacy interface device may not be stocked in every quantity, but a search-page availability statement does not establish a guaranteed current lead time. Provide the required quantity, shipment date, target package, and traceability requirements when requesting the quotation.

Engineering reference data for DS90CR285SLC — comparison, design guidance, and compliance information.

Selection Guide

Choose the DS90CR285SLC when a design specifically requires a 28-bit parallel-to-four-pair LVDS transmitter operating from 3 V to 3.6 V at up to 66 MHz. Its integrated rising-edge data-strobe function suits point-to-point links, compact backplanes, data-acquisition equipment, and legacy industrial or telecommunications systems. It is less attractive for new RoHS-constrained programs because the device is documented as RoHS non-compliant and contains lead. Do not substitute a receiver, serializer with a different lane count, or merely similar LVDS transmitter without checking every ball assignment and timing parameter. Because no confirmed drop-in replacement was identified, the safest substitution strategy is to reuse the existing 64-NFBGA layout only after a manufacturer-documented electrical and pin-compatibility review. For a new design with different data width, supply voltage, channel count, or lifecycle requirements, evaluate a currently supported interface IC instead of forcing this legacy transmitter into the system.

Comparison with Alternatives

Parameter This Product
Brand Texas Instruments
Package 64-NFBGA (8 x 8 mm)
Product Type 28-bit rising-edge data-strobe LVDS transmitter
Supply Voltage Range 3 V to 3.6 V
Maximum Clock Frequency 66 MHz
Parallel Input Width 28 bits
Input Logic LVCMOS/LVTTL
Output Logic 4 differential LVDS outputs
RoHS Status RoHS non-compliant

Key Differentiators

  • Four differential LVDS data outputs from a 28-bit parallel bus (vs No qualified pin-compatible alternative was established)
  • Rising-edge data-strobe architecture (vs No qualified pin-compatible alternative was established)
  • Compact 64-NFBGA implementation (vs No qualified pin-compatible alternative was established)

Design Notes

Route every LVDS pair as a tightly coupled, impedance-controlled differential pair over a continuous reference plane. Keep the pair geometry consistent through vias, connectors, and layer transitions, and minimize stubs. Treat the four data lanes and forwarded clock as a coordinated channel: excessive pair-length mismatch or clock-to-data skew can reduce receiver margin even when the transmitter itself operates correctly.

Confirm the receiver termination, AC-coupling arrangement, input thresholds, and maximum clock-to-data tolerance as one complete channel design. Place the receiver-side termination at the appropriate termination point in the physical topology and avoid adding unneeded parallel termination. Validate the assembled transmitter, PCB or cable, connector, and receiver at the intended 66 MHz operating condition rather than testing only the source IC.

Use the official 64-ball pin-description table to assign power, ground, differential outputs, parallel inputs, clock, and no-connect balls before schematic capture. Check the 8 x 8 mm BGA escape strategy and ensure that assembly inspection can verify the dense ball array. Maintain uninterrupted return paths beneath the BGA and test points, and avoid placing noisy switching circuitry directly beneath the high-speed interface region.

Do not select a similarly described serializer as a substitute merely because its package or data rate appears similar. A valid replacement must preserve the 28-bit input, four-pair LVDS output, forwarded-clock behavior, electrical timing, supply requirements, and every 64-ball assignment. Also review the documented RoHS non-compliant and contains-lead statuses before using the device in new commercial or regulated production programs.

Compliance Information

RoHS
Non Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
No
Halogen Free
Unknown
Conflict Minerals
Unknown

The component documentation identifies the DS90CR285SLC as RoHS non-compliant and containing lead. REACH, halogen-free, conflict-minerals, and automotive qualification status are unknown.

Data verified on: 2026-11-10 — data verified and curated by XAIPART's component engineering team

Related Searches

DS90CR285SLC datasheet DS90CR285SLC datasheet pdf DS90CR285SLC pinout DS90CR285SLC 64-NFBGA DS90CR285SLC equivalent DS90CR285SLC replacement DS90CR285SLC drop-in substitute DS90CR285SLC 66 MHz LVDS transmitter DS90CR285SLC 28-bit LVDS interface Texas Instruments DS90CR285SLC DS90CR285SLC price DS90CR285SLC stock DS90CR285SLC industrial data link DS90CR285SLC display interface

Related Components & Terms

Texas Instruments DS90CR285SLC DS90CR285 LVDS LVCMOS LVTTL rising-edge data-strobe 28-bit parallel input four differential LVDS outputs 66 MHz clock 3 V to 3.6 V supply 64-NFBGA 8 x 8 mm BGA surface mount interface IC serializer parallel-to-LVDS converter low-voltage differential signaling differential signal pair controlled-impedance routing receiver termination clock-to-data skew data acquisition industrial control display interface
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details