ICS548G-05 - Low-Jitter PLL Clock Synthesizer | Renesas
MPN: ICS548G-05 ✗ End of LifeICS548G-05 Overview
A PLL clock synthesizer is a clock-and-timing integrated circuit that multiplies or divides a reference signal and then distributes the resulting clock through dedicated output drivers. Within the product hierarchy, the ICS548G-05 is a clock synthesizer and frequency multiplier, a member of the broader PLL and clock-management IC category, and ultimately part of the semiconductor timing-control ecosystem. Its low-jitter design makes it useful where the synthesized clock must support timing-sensitive digital or communications functions.
Key features include a 16-pin TSSOP package, a 3.15 V to 5.5 V supply range, and synthesis of x16 and x24 clocks from T1 and E1 frequencies. The manufacturer describes the ICS548-05 as a low-cost, high-performance clock synthesizer using patented analog/digital PLL techniques. It accepts a crystal or clock input and generates popular communications frequencies, allowing multiple related clock outputs to replace separate oscillator arrangements. The listed 49.152 MHz output is directly associated with audio-clock and sampling-rate use cases.
The PLL architecture separates frequency generation from the external reference source. A crystal or clock input establishes the reference, while the internal synthesizer produces the required derived clock frequencies. Output drivers then provide CLK and related divided or multiplied clock signals. Publicly indexed descriptions also identify CLK and CLK/2 outputs, tri-state capability, and low-skew clock distribution, making the device relevant to designs that need multiple synchronized signals rather than a simple single-ended oscillator.
Typical uses include MP3 and digital-audio systems, communications equipment operating around T1 and E1 timing, and clock trees for digital signal processors, converters, and interface logic. The 16-TSSOP format supports compact surface-mount assemblies while exposing reference, power, control, and clock-output functions. In a typical circuit, the reference source and required decoupling capacitors are placed close to the device, while each clock trace is routed to minimize loading and preserve edge quality.
Design attention should center on reference stability, correct mode selection, output loading, and power sequencing. Because PLL jitter and phase error depend on the reference source and loop operating conditions, the crystal or external clock must meet the timing requirements stated in the manufacturer datasheet. Keep clock traces short, avoid unnecessary stubs, and use controlled-impedance routing when the output drives longer PCB paths. Confirm all supply, ground, and output connections against the package pin-description table before layout release.
This product page combines the manufacturer's device description with practical clock-tree guidance, drop-in option analysis, and application-oriented design context. It helps engineers distinguish the ICS548G-05 from ordinary fixed-frequency oscillators and generic dividers by focusing on its PLL-based synthesis, x16 and x24 multiplication functions, low-jitter communications-clock role, and compact 16-TSSOP implementation.
Drop-in alternatives for ICS548G-05 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
ICS548G-05I
✅ Drop-In📋 Reference alternative (not in catalog)
ICS548G-05C
✅ Drop-In📋 Reference alternative (not in catalog)
ICS548G-05LF
✅ Drop-In📋 Reference alternative (not in catalog)
548G-05LF
✅ Drop-In📋 Reference alternative (not in catalog)
ICS548G-05 Specifications
| Device Type | PLL clock synthesizer and frequency multiplier |
| Listed Output Frequency | 49.152 MHz |
| Supply Voltage Range | 3.15 V to 5.5 V |
| Input Frequency | 2.05 MHz |
| Multiplication Functions | x16 and x24 |
| Reference Input | Crystal or clock input |
| PLL Architecture | Analog/digital phase-locked loop |
| Output Signals | CLK and CLK/2 |
| Clock Skew | 500 ps |
| Non-PLL Maximum Clock Input | 160 MHz |
| Output Enable | Tri-state capable outputs |
| Power-Down Control | Whole-chip power-down control |
| Bus Interface | CMOS |
| Package | 16-pin TSSOP, 4.40 mm width |
| Mounting Type | Surface mount |
| Packaging Form | Tube |
ICS548G-05 16-pin tssop, 4.40 mm width Pin Configuration Guide
Pin configuration for ICS548G-05 (16-pin tssop, 4.40 mm width package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for ICS548G-05.
Refer to the datasheet for full pin configuration.
Typical Applications
ICS548G-05 is suitable for 6 applications: Digital Audio Sampling Clock, MP3 Player Timing, T1 and E1 Communications Timing, Precision Clock-Distribution Tree, Industrial Control and Instrumentation, Interface and Processor Clocking.
Digital Audio Sampling Clock
The ICS548G-05 fits digital-audio clock generation because it synthesizes x16 and x24 clocks from T1 and E1-related reference frequencies and is associated with a 49.152 MHz output. Place it upstream of an audio converter or digital audio interface, and derive the required sampling clock from a common crystal reference. The low-jitter PLL architecture helps preserve signal-chain timing quality, while the 3.15 V to 5.5 V supply range supports both 3.3 V and 5 V systems. Validate the output frequency, reference tolerance, and jitter against the receiving converter before release.
Recommended
MP3 Player Timing
ICS548G-05 was designed to produce audio sampling rates used in MP3 systems, making it appropriate for compact digital players and portable media electronics. A single crystal reference can feed the PLL, which generates the required multiplied clock instead of requiring several unrelated oscillators. This reduces clock-source count and supports a coordinated distribution network for the codec, memory interface, and signal-conversion stages. Keep the reference path short, provide local supply decoupling, and route the synthesized clock directly toward the codec clock input.
Recommended
T1 and E1 Communications Timing
The ICS548G-05 is designed to derive x16 and x24 clock outputs from T1 and E1 frequencies, making it suitable for communications equipment requiring related clocks from a common reference. Its analog/digital PLL architecture accepts either a crystal or an external clock and generates the desired timing frequencies. In a line-card or transport design, distribute the synthesized outputs with controlled impedance and equalize loading where multiple branches are required. Verify PLL lock behavior and reference stability under operating temperature.
Recommended
Precision Clock-Distribution Tree
ICS548G-05 can form the synthesis stage of a small clock tree because it provides CLK and CLK/2 outputs in a compact 16-TSSOP package. Its documented 500 ps output skew supports closely related edges when feeding compatible logic. The device can replace separate oscillator and divider arrangements where x16 and x24 multiples are needed from one reference. Keep fanout within the electrical limits, avoid long unterminated branches, and provide separate clock routing for each destination to minimize edge degradation.
Recommended
Industrial Control and Instrumentation
The ICS548G-05 can supply common synthesized clocks to industrial control, test, and measurement boards that need multiple related frequencies rather than one fixed oscillator output. The 3.15 V to 5.5 V operating range supports common embedded control rails, while the TSSOP package simplifies board-level assembly. Use a low-noise reference, isolate the PLL from switching regulators and high-current traces, and provide adequate ground-plane continuity. Confirm startup, lock, and output behavior across the complete industrial temperature range before deployment.
Recommended
Interface and Processor Clocking
ICS548G-05 is useful in processor-based designs where one reference must feed multiple related clock domains. The PLL-derived x16 and x24 outputs can support digital interfaces, converters, and peripheral timing while reducing the number of separate oscillators. Place the device near the reference source, route the high-speed outputs as controlled-impedance nets, and avoid introducing test pads or long stubs on sensitive clock paths. Validate setup and hold timing at each receiver because PCB skew is added to the device's specified output skew.
Recommended
Recommended Products Summary
Engineering reference data for ICS548G-05 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ICS548G-05I | ICS548G-05C | ICS548G-05LF | 548G-05LF |
|---|---|---|---|---|---|
| Package | TSSOP-16 | TSSOP-16 | TSSOP-16 | TSSOP-16 | TSSOP-16 |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Device Function | PLL clock synthesizer and T1/E1 frequency multiplier | PLL clock synthesizer and T1/E1 frequency multiplier | PLL clock synthesizer and T1/E1 frequency multiplier | PLL clock synthesizer and T1/E1 frequency multiplier | PLL clock synthesizer and T1/E1 frequency multiplier |
| Listed Output Frequency | 49.152 MHz | 49.152 MHz | 49.152 MHz | 49.152 MHz | 49.152 MHz |
| Supply Voltage Range | 3.15 V to 5.5 V | 3.15 V to 5.5 V | 3.15 V to 5.5 V | 3.15 V to 5.5 V | 3.15 V to 5.5 V |
| Input Frequency | 2.05 MHz | 2.05 MHz | 2.05 MHz | 2.05 MHz | 2.05 MHz |
| Synthesis Functions | x16 and x24 | x16 and x24 | x16 and x24 | x16 and x24 | x16 and x24 |
| Clock Skew | 500 ps | 500 ps | 500 ps | 500 ps | 500 ps |
| Output States | CLK and CLK/2 with tri-state capability | CLK and CLK/2 with tri-state capability | CLK and CLK/2 with tri-state capability | CLK and CLK/2 with tri-state capability | CLK and CLK/2 with tri-state capability |
| Qualification or Ordering Suffix | G-05 | I ordering suffix | C ordering suffix | LF ordering suffix | Shortened LF ordering code |
Key Differentiators
- PLL synthesis replaces separate oscillator and divider arrangements (vs ICS548G-05I)
- Compact multi-output timing in a standard TSSOP footprint (vs ICS548G-05C)
- Lead-free ordering configuration is available without changing the land pattern (vs 548G-05LF)
Design Notes
Place the crystal or clock-reference components close to the ICS548G-05 and keep the reference path short and compact. Use a continuous ground plane beneath the device and avoid routing the reference net near switching nodes, high-current inductors, and isolation barriers. A stable reference reduces phase errors in the PLL. When the input comes from an external oscillator, verify amplitude, duty cycle, and edge rate against the manufacturer electrical-characteristics table before layout approval.
Treat CLK and CLK/2 as high-speed signals even though the device produces relatively low-frequency audio and communications clocks. Use short traces, minimize stubs, avoid test pads where practical, and maintain consistent return paths beneath the clock nets. If a clock is branched, account for the capacitance and loading of each receiver. The documented 500 ps output skew applies to the device outputs, while additional PCB and receiver skew must be included in end-to-end timing analysis.
Decouple the 3.15 V to 5.5 V supply locally at the device and keep the power loop compact. Place the decoupling capacitor between the relevant power and ground pins, provide a low-impedance ground connection, and route clock outputs away from the supply return path of switching circuitry. Startup and power-down sequencing should follow the manufacturer application guidance. If outputs are tri-stated during reset or power transitions, verify that downstream receivers tolerate an undefined or high-impedance clock state.
Do not substitute the ICS548G-05 for a generic frequency divider solely because both produce clocks; the device uses PLL synthesis and has a defined reference and mode configuration. Check the ordering suffix, package, supply range, reference frequency, output frequency, and grade-specific limits before replacing a component. Also avoid assuming that the 49.152 MHz headline value is the only available output configuration. Use the device's mode and frequency tables when configuring x16 and x24 synthesis.
Compliance Information
The LF ordering suffix identifies a lead-free configuration, but formal RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 declarations are not stated on the manufacturer page. Confirm current declarations with Renesas Electronics.